Winbond Electronics W78LE51P-24, W78LE51F-24, W78LE51-24 Datasheet

Preliminary W78LE51

8-BIT MTP MICROCONTROLLER

Publication Release Date: December 1998

- 1 - Revision A1

GENERAL DESCRIPTION

The W78LE51 is an 8-bit microcontroller which can accommodate a wide supply voltage range with
low power consumption. The instruction set for the W78LE51 is fully compatible with the standard

8051. The W78LE51 contains an 4K bytes MTP ROM (Multiple-Time Programmable ROM); a 128
bytes RAM; four 8-bit bi-directional and bit-addressable I/O ports; an additional 4-bit I/O port P4; two
16-bit timer/counters; a hardware watchdog timer and a serial port. These peripherals are supported
by seven sources two-level interrupt capability. To facilitate programming and verification, the MTP­ROM inside the W78LE51 allows the program memory to be programmed and read electronically.
Once the code is confirmed, the user can protect the code for security.

The W78LE51 microcontroller has two power reduction modes, idle mode and power-down mode,
both of which are software selectable. The idle mode turns off the processor clock but allows for
continued peripheral operation. The power-down mode stops the crystal oscillator for minimum power
consumption. The external clock can be stopped at any time and in any state without affecting the
processor.

FEATURES

• Fully static design 8-bit CMOS microcontroller

• Wide supply voltage of 2.4V to 5.5V

• 128 bytes of on-chip scratchpad RAM

• 4 KB electrically erasable/programmable MTP-ROM

• 64 KB program memory address space

• 64 KB data memory address space

• Four 8-bit bi-directional ports

• One extra 4-bit bit-addressable I/O port, additional

INT2

/ INT3

(available on 44-pin PLCC/QFP package)

• Two 16-bit timer/counters

• One full duplex serial port(UART)

• Watchdog Timer

• seven sources, two-level interrupt capability

• EMI reduction mode

• Built-in power management

• Code protection mechanism

• Packages:

− DIP 40: W78LE51-24

− PLCC 44: W78LE51P-24

− PQFP 44: W78LE51F-24

Preliminary W78LE51

- 2 -

PIN CONFIGURATIONS

VDD1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20

39

40

34

35

36

37

38

30

31

32

33

26

27

28

29

21

22

23

24

25

P0.0, AD0

P0.1, AD1

P0.2, AD2

P0.3, AD3

P0.4, AD4

P0.5, AD5

P0.6, AD6

P0.7, AD7

EA

ALE

PSEN

P2.5, A13

P2.6, A14

P2.7, A15

P2.0, A8

P2.1, A9

P2.2, A10

P2.3, A11

P2.4, A12

P1.0

40-Pin DIP (W78LE51)

P1.2
P1.3
P1.4
P1.5
P1.6

RXD, P3.0
TXD, P3.1

P1.7
RST

INT0, P3.2
INT1, P3.3

T0, P3.4
T1, P3.5

WR, P3.6

RD, P3.7

XTAL1

XTAL2

VSS

P1.1

44-Pin PLCC (W78LE51P)

44-Pin QFP (W78LE51F)

34

4039 38 37 36

3544

43 42 41

33
32
31
30
29
28
27
26
25
24
23

P0.4, AD4
P0.5, AD5
P0.6, AD6
P0.7, AD7
EA

ALE
PSEN

P2.7, A15
P2.6, A14
P2.5, A13

22212019181716151413

12

11

4

3

2

1

8

7

6

5

10

9

P1.5
P1.6
P1.7
RST

RXD, P3.0

TXD, P3.1

INT0, P3.2

INT1, P3.3

T0, P3.4
T1, P3.5

X
T
A
L
1

V
S
S

P
2
.
4
,
A
1
2

P
2
.
3
,
A
1
1

P
2
.
2
,
A
1
0

P
2
.
1
,
A
9

P
2
.
0
,
A
8

X
T
A
L
2

P
3
.
7
,
/
R
D

P
3
.
6
,
/
W
R

A
D
3
,
P
0
.
3

P
1
.
0

P
1
.
2

V
D
D

A
D
2
,
P
0
.
2

A
D
1
,
P
0
.
1

A
D
0
,
P
0
.
0

P
1
.
1

P
1
.
3

P
1
.
4

40

2 1 44 43 42

41

6 5 4 3

39
38
37
36
35
34
33
32
31
30
29

P0.4, AD4
P0.5, AD5
P0.6, AD6
P0.7, AD7
EA

ALE
PSEN

P2.7, A15
P2.6, A14
P2.5, A13

2827262524232221201918

17

10

9

8

7

14

13

12

11

16

15

P1.5
P1.6
P1.7

RST

RXD, P3.0

TXD, P3.1
INT0, P3.2
INT1, P3.3

T0, P3.4
T1, P3.5

A
D
3
,
P
0
.
3

P
1
.
0

P
1
.
2

V
D
D

A
D
2
,
P
0
.
2

A
D
1
,
P
0
.
1

A
D
0
,
P
0
.
0

P
1
.
1

P
1
.
3

P
1
.
4

X
T
A
L
1

V
S
S

P
2
.
4
,
A
1
2

P
2
.
3
,
A
1
1

P
2
.
2
,
A
1
0

P
2
.
1
,
A
9

P
2
.
0
,
A
8

X
T
A
L
2

P
3
.
7
,
/
R
D

P
3
.
6
,
/
W
R

P
4
.
0

/
I
N
T
3
,
P
4
.
2

P4.1

P4.1

P
4
.
0

INT2, P4.3

INT2, P4.3

/
I
N
T
3
,
P
4
.
2

Preliminary W78LE51

Publication Release Date: December 1998

- 3 - Revision A1

PIN DESCRIPTION

SYMBOL DESCRIPTIONS

EA

EXTERNAL ACCESS ENABLE: This pin forces the processor to execute out of
external ROM. It should be kept high to access internal ROM. The ROM address and

data will not be presented on the bus if EA pin is high and the program counter is
within on-chip ROM area.

PSEN

PROGRAM STORE ENABLE:

PSEN

enables the external ROM data onto the Port 0

address/ data bus during fetch and MOVC operations. When internal ROM access is
performed, no

PSEN

strobe signal outputs from this pin.

ALE

ADDRESS LATCH ENABLE: ALE is used to enable the address latch that separates
the address from the data on Port 0.

RST

RESET: A high on this pin for two machine cycles while the oscillator is running resets
the device.

XTAL1

CRYSTAL1: This is the crystal oscillator input. This pin may be driven by an external
clock.

XTAL2

CRYSTAL2: This is the crystal oscillator output. It is the inversion of XTAL1.

VSS

GROUND: Ground potential

VDD

POWER SUPPLY: Supply voltage for operation.

P0.0−P0.7

PORT 0: Port 0 is a bi-directional I/O port which also provides a multiplexed low order
address/data bus during accesses to external memory. The pins of Port 0 can be
individually configured to open-drain or standard port with internal pull-ups.

P1.0−P1.7

PORT 1: Port 1 is a bi-directional I/O port with internal pull-ups. The bits have
alternate functions which are described below:

T2(P1.0): Timer/Counter 2 external count input
T2EX(P1.1): Timer/Counter 2 Reload/Capture control

P2.0−P2.7

PORT 2: Port 2 is a bi-directional I/O port with internal pull-ups. This port also provides
the upper address bits for accesses to external memory.

P3.0−P3.7

PORT 3: Port 3 is a bi-directional I/O port with internal pull-ups. All bits have alternate
functions, which are described below:

RXD(P3.0) : Serial Port receiver input
TXD(P3.1) : Serial Port transmitter output

INT0 (P3.2) : External Interrupt 0

INT1

(P3.3) : External Interrupt 1
T0(P3.4) : Timer 0 External Input
T1(P3.5) : Timer 1 External Input

WR

(P3.6) :External Data Memory Write Strobe

RD

(P3.7) : External Data Memory Read Strobe

P4.0−P4.3

PORT 4: Another bit-addressable bidirectional I/O port P4. P4.3 and P4.2 are
alternative function pins. It can be used as general I/O port or external interrupt input

sources (

INT2

/INT3 ).

Preliminary W78LE51

- 4 -

BLOCK DIAGRAM

P3.0
~
P3.7

P1.0

~

P1.7

ALU

Port 0
Latch

Port 1
Latch

Timer

1

Timer

0

Port

1

UART

XTAL1

PSENALE

Vss

V

RST

XTAL2

Oscillator

Interrupt

PSW

Instruction

Decoder

&

Sequencer

Reset Block

Bus & Clock

Controller

SFR RAM

Address

Power control

128 bytes

RAM & SFR

Stack

Pointer

B

Addr. Reg.

Incrementor

PC

DPTR

Temp Reg.

T2

T1

ACC

Port 3

Latch

Port 4

Latch

Port

3

Port 2

Latch

P4.0
~
P4.3

Port

4

Port

0

Port

2

P2.0
~
P2.7

P0.0
~
P0.7

INT2

INT3

Watchdog

Timer

ROM

DD

FUNCTIONAL DESCRIPTION

The W78LE51 architecture consists of a core controller surrounded by various registers, five general
purpose I/O ports, 128 bytes of RAM, two timer/counters, and a serial port. The processor supports
111 different opcodes and references both a 64K program address space and a 64K data storage
space.

New Defined Peripheral

In order to be more suitable for I/O, an extra 4-bit bit-addressable port P4 and two external interrupt

INT2

, INT3 has been added to either the PLCC or QFP 44 pin package. And description follows:

1.

INT2

/ INT3

Two additional external interrupts,

INT2

and INT3 , whose functions are similar to those of external
interrupt 0 and 1 in the standard 80C52. The functions/status of these interrupts are determined/
shown by the bits in the XICON (External Interrupt Control) register. The XICON register is bit-

Preliminary W78LE51

Publication Release Date: December 1998

- 5 - Revision A1

addressable but is not a standard register in the standard 80C52. Its address is at 0C0H. To set/clear
bits in the XICON register, one can use the "SETB (/CLR) bit" instruction. For example, "SETB 0C2H"
sets the EX2 bit of XICON.

XICON - external interrupt control (C0H)

PX3 EX3 IE3 IT3 PX2 EX2 IE2 IT2

PX3: External interrupt 3 priority high if set
EX3: External interrupt 3 enable if set
IE3: If IT3 = 1, IE3 is set/cleared automatically by hardware when interrupt is detected/serviced
IT3: External interrupt 3 is falling-edge/low-level triggered when this bit is set/cleared by software
PX2: External interrupt 2 priority high if set
EX2: External interrupt 2 enable if set
IE2: If IT2 = 1, IE2 is set/cleared automatically by hardware when interrupt is detected/serviced
IT2: External interrupt 2 is falling-edge/low-level triggered when this bit is set/cleared by software

Eight-source interrupt informations:

INTERRUPT

SOURCE

VECTOR

ADDRESS

POLLING

SEQUENCE WITHIN

PRIORITY LEVEL

ENABLE

REQUIRED

SETTINGS

INTERRUPT

TYPE

EDGE/LEVEL

External Interrupt 0 03H 0 (highest) IE.0 TCON.0
Timer/Counter 0 0BH 1 IE.1 ­External Interrupt 1 13H 2 IE.2 TCON.2
Timer/Counter 1 1BH 3 IE.3 ­Serial Port 23H 4 IE.4 ­External Interrupt 2 33H 5 XICON.2 XICON.0
External Interrupt 3 3BH 6 (lowest) XICON.6 XICON.3

2. PORT4

Another bit-addressable port P4 is also available and only 4 bits (P4<3:0>) can be used. This port
address is located at 0D8H with the same function as that of port P1, except the P4.3 and P4.2 are

alternative function pins. It can be used as general I/O pins or external interrupt input sources (

INT2

,

INT3 ).

Example:

P4 REG 0D8H

MOV P4, #0AH ; Output data "A" through P4.0−P4.3.

MOV A, P4 ; Read P4 status to Accumulator.
SETB P4.0 ; Set bit P4.0
CLR P4.1 ; Clear bit P4.1

3. Reduce EMI Emission

Because of on-chip MTP-ROM, when a program is running in internal ROM space, the ALE will be
unused. The transition of ALE will cause noise, so it can be turned off to reduce the EMI emission if it

Preliminary W78LE51

- 6 -

is useless. Turning off the ALE signal transition only requires setting the bit 0 of the AUXR SFR,
which is located at 08Eh. When ALE is turned off, it will be reactivated when the program accesses
external ROM/RAM data or jumps to execute an external ROM code. The ALE signal will turn off
again after it has been completely accessed or the program returns to internal ROM code space. The
AO bit in the AUXR register, when set, disables the ALE output. In order to reduce EMI emission from
oscillation circuitry, W78LE51 allows user to diminish the gain of on-chip oscillator amplifiers by using
programmer to clear the B7 bit of security register. Once B7 is set to 0, a half of gain will be
decreased. Care must be taken if user attempts to diminish the gain of oscillator amplifier, reducing a
half of gain may effect to external crystal operating improperly at high frequency above 24 MHz. The
value of R and C1,C2 may need some adjustment while running at lower gain.

***AUXR - Auxiliary register (8EH)

- - - - - - - AO

AO: Turn off ALE output.

4. Power-off Flag

***PCON - Power control (87H)

- -

-

POF

GF1 GF0 PD IDL

POF: Power off flag. Bit is set by hardware when power on reset. It can be cleared by software

to determine chip reset is a warm boot or cold boot.
GF1, GF0: These two bits are general-purpose flag bits for the user.
PD: Power down mode bit. Set it to enter power down mode.
IDL: Idle mode bit. Set it to enter idle mode.

The power-off flag is located at PCON.4. This bit is set when VDD has been applied to the part. It can
be used to determine if a reset is a warm boot or a cold boot if it is subsequently reset by software.

Watchdog Timer

The Watchdog timer is a free-running timer which can be programmed by the user to serve as a
system monitor, a time-base generator or an event timer. It is basically a set of dividers that divide
the system clock. The divider output is selectable and determines the time-out interval. When the
time-out occurs a system reset can also be caused if it is enabled. The main use of the Watchdog
timer is as a system monitor. This is important in real-time control applications. In case of power
glitches or electro-magnetic interference, the processor may begin to execute errant code. If this is
left unchecked the entire system may crash. The watchdog time-out selection will result in different
time-out values depending on the clock speed. The Watchdog timer will de disabled on reset. In
general, software should restart the Watchdog timer to put it into a known state. The control bits that
support the Watchdog timer are discussed below.

Watchdog Timer Control Register

Bit: 7 6 5 4 3 2 1 0

ENW CLRW WIDL - - PS2 PS1 PS0

Mnemonic: WDTC Address: 8FH

ENW : Enable watch-dog if set.

Preliminary W78LE51

Publication Release Date: December 1998

- 7 - Revision A1

CLRW: Clear watch-dog timer and prescaler if set. This flag will be cleared automatically
WIDL : If this bit is set, watch-dog is enabled under IDLE mode. If cleared, watch-dog is disabled

under IDLE mode. Default is cleared.

PS2, PS1, PS0: Watch-dog prescaler timer select. Prescaler is selected when set PS2−0 as follows:

PS2 PS1 PS0 PRESCALER SELECT

0 0 0 2
0 1 0 4
0 0 1 8
0 1 1 16
1 0 0 32
1 0 1 64
1 1 0 128
1 1 1 256

The time-out period is obtained using the following equation:

1

OSC

2 PRESCALER 1000 12 mS

14

× × × ×

Before Watchdog time-out occurs, the program must clear the 14-bit timer by writing 1 to WDTC.6
(CLRW). After 1 is written to this bit, the 14-bit timer , prescaler and this bit will be reset on the next
instruction cycle. The Watchdog timer is cleared on reset.

OSC 1/12

PRESCALER

14-BIT TIMER

CLEAR

CLRW

EXTERNAL

RESET

INTERNAL

RESET

WIDL

IDLE

ENW

Watchdog Timer Block Diagram

Typical Watch-Dog time-out period when OSC = 20 MHz

PS2 PS1 PS0 WATCHDOG TIME-OUT PERIOD

0 0 0 19.66 mS
0 1 0 39.32 mS
0 0 1 78.64 mS
0 1 1 157.28 mS