Wilson Electronics 801306 Installation Manual

Wilson Electronics, Inc.

3301 E. Deseret Drive, St. George, Utah 84790

For additional technical support visit

www.wilsonelectronics.com

Phone: [phone] Fax: [phone]

IN-BUILDING

Wir eless

The term “IC:” before the radio certification number signifies

that Industry of Canada technical specifications were met.

PCS Smart Technology™ Amplifier
Installation Guide

In-Building

Wireless PCS

Smart TechnologyTM Amplier

PART # 801306

1850-1990 MHz

FCC ID: PWO8013SB

IC: 4726A-8013SB

2

3

1. PURPOSE OF THE AMPLIFIER

The PCS Smart TechnologyTM Amplier improves RF coverage for areas in which low signal

strength is a concern.

2. PACKAGE CONTENTS

2.1 Amplier

2.2 AC/DC 110 volt Power Supply

3. HOW THE AMPLIFIER FUNCTIONS

The signal is received by the outside antenna from the cell site. The signal is then
AMPLIFIED and transmitted to your phone through the inside antenna. When the phone
transmits, the signal is received by the inside antenna and then AMPLIFIED and transmitted
to the cell site through the outside antenna.

4. AMPLIFIER INSTALLATION (see illustration on pg. 4 & 5)

4.1 Installing the Wilson Cellular Outside Antenna

WARNING: The outside antenna used with this amplier must be xed-mounted on

an outdoor permanent structure with a separation of at least 20 feet from all persons
during normal operation.

4.1.1 Select a location on the roof using your phone in test mode to nd the best signal
strength. (See leaet titled PHONE TEST MODES)

4.1.2 The outside antenna should be located in an area with at least a 3 foot radius clear of
obstructions and other radiating elements.

4.2 Installing The Amplier

WARNING: Connecting amplier directly to cell phone may damage phone.

WARNING: Connect both antennas before connecting power to the amplier.

4.2.1 Mount the AMPLIFIER on a wall or ceiling using #6 screws.

NOTE: Mount the AMPLIFIER away from direct sunlight, excessive heat and/or

moisture. The amplifier needs proper ventilation. DO NOT place the amplifier
in an air-tight enclosure.

4.2.2 Connect outside antenna to the amplier side labeled “OUTSIDE ANTENNA”.

4.2.3 Connect inside antenna to the amplier side labeled “INSIDE ANTENNA”.

4.2.4 Verify that both the outside and inside antennas are connected before connecting
the AC-DC power supply to the power outlet.

3

4.4 Installing The Wilson Cellular Inside Antenna

4.4.1 See antenna packaging for model specic instructions.

4.4.2 The inside antenna should be centered in the weak signal area. The inside antenna
should be at least 7 feet from the oor.

FCC Separation Warning

WARNING: The inside antenna used with this amplier must have a separation

distance from all persons that is at least:
9 inches for the 2.5 dBi Dome antenna.
14 inches for the 7 dBi Panel antenna.
The amplier must not be co-located or operating in conjunction with any other
antenna or amplier.

4.5 When covering multiple areas a 1900 MHz splitter can be used to allow for more than one
inside antenna. Extension cables can also be used if the weak signal area is located far from the
location of the outside antenna. For coax runs more than 20 feet use 9913 or equivalent coax.

NOTE: For Maximum gain (60 dB), keep a separation distance of at least 50 feet

between the outside and inside antennas. Closer spacings may be used,
but may cause the amplier to automatically reduce its gain.

NOTE: When using a Yagi antenna make sure the Yagi is pointed away from the

inside antenna.

ALL LIGHTS GREEN = 60 dB GAIN

LIGHT D OFF = 2 dB REDUCTION

LIGHT D & C OFF = 10 dB REDUCTION

LIGHT D, C & B OFF = 20 dB REDUCTION

LIGHT A RED = 40 dB REDUCTION

4.3 Indicator Lights