Wilson Electronics 801101, 804002 Installation Manual

Signal Booster
Installation
Guide
Mobile Wireless Single Band Signal Booster
Contents:
How it Works ...................................1
Before Getting Started ............................2
Installing a Wilson Electronics Outside Antenna ........3
Installing a Wilson Electronics Signal Booster. . . . . . . . . . 4
Installing the Low-Profile Antenna ...................5
Powering Up a Wilson Electronics Signal Booster . . . . . . 6
Warnings and Recommendations ...................7
Understanding the Signal Booster Lights . . . . . . . . . . . . . 8
About Wilson Electronics ..........................9
Guarantee and Warranty .........................10
Signal Booster Specifications . . . . . . . . . . . . . .Back Cover
Wilson
®
Electronics, Inc.
Note: This manual contains important safety and operating information.
Please read and follow the instructions in this manual. Failure to do so could be hazardous and result in damage to your signal booster.
1
Contact Wilson Electronics Tech Support with any questions at 866-294-1660
Or email: tech@wilsonelectronics.com Hours: 7am to 6pm MST.
2
Installation Instructions for the Following Wilson Electronics Signal Boosters:
Mobile Wireless Single Band Cellular Signal Booster
Model #801101 FCC ID: PWO824WV IC: 4726A-824WV
Mobile Wireless Single Band iDEN Signal Booster
Model #804002 FCC ID: PWO806WV IC: 4726A-806WV
The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met.
Inside this Package
How it Works
Your new Wilson Electronics signal booster has been carefully engineered to significantly improve the performance of your cell phone or cellular data card in mobile applications. Together with an outside antenna (sold separately), the signal booster’s state-of-the-art technology is designed to increase your signal up to 10 times, reduce disconnects and dropouts, and increase data communication rates needed for 3G technologies.
The outside antenna will collect the cell tower signal and send it through the cable to the signal booster. The signal is then boosted and sent to the inside antenna. Your cell phone or data card then communicates with the improved signal. When the cell phone or data card transmits, the signal goes through the inside antenna, is boosted by the signal booster and broadcast back to the cell tower through the outside antenna.
Wilson Electronics manufactures a wide variety of antennas to help you customize your signal booster for your specific application. Several are shown below. See your dealer or visit www.wilsonelectronics.com.
Wireless
Signal Booster
DC plug-in
power cable
NMO
Mount
301104
Magnet
Mount
301103
Trucker
Mount
301101
Mini Magnet 301113
Marine
Antenna
301130
Low-profile
antenna
NOTE: Use of this signal booster with an antenna gain higher than
5.12 dBi is in violation of FCC regulations for which the offender is fully liable. All Wilson mobile antennas are
5.12 dBi or less in the 800 MHz band.
2
Contact Wilson Electronics Tech Support with any questions at 866-294-1660
Or email: tech@wilsonelectronics.com Hours: 7am to 6pm MST.
Before Getting Started
This guide will help you properly install Wilson Electronics single-band, mobile wireless signal booster. It is important to read through all of the installation steps for your particular application prior to installing any equipment. Read through the instructions, visualize where all the equipment will need to be installed and do a soft installation before mounting any equipment. If you do not understand the instructions in full, seek professional help, or contact Wilson Electronics Technical Support at 866-294-1660.
Warning: In a wireless installa­tion, do not plug the signal booster directly into the cell phone or data card using an antenna adapter. It will damage the signal booster.
!
Outside
Antenna
Inside
Antenna
Signal booster
DC Power
Supply
Cell Phone
PDA
Notebook
Installation Diagram
3
Contact Wilson Electronics Tech Support with any questions at 866-294-1660
Or email: tech@wilsonelectronics.com Hours: 7am to 6pm MST.
4
Installing a Wilson Electronics Outside Antenna
To receive the best cell signal, select a location in the center of the vehicle’s roof at least 20 inches away from any other antennas and free of obstructions.
Follow the specific antenna installation instructions included with the outside antenna (sold separately).
The outside antenna must be installed vertically. Signal performance will be degraded if the antenna is not vertical.
The antenna cable may run through the door to the signal booster.
The antenna cable is small enough to easily tuck under the door seal or plastic molding.
For a more professional-looking installation, run the antenna cable under the door seal. Carefully pull down the door seal. Run the cable through the seal and push the seal back into place. This prevents constant wear and tear on the cable as the door
opens and closes.
Optional Magnet-
Mount Antenna
Shown
Part #301103
Carefully Pull Down Door Seal
Run Cable
Under
Seal
Tuck Cable Under Seal
Warning:
Warning:
The outside antenna must be installed with a separation of at least 20 inches from any of the vehicle’s occupants or nearby persons and must not be located or operating in conjunction with any other antenna or signal booster.
Do not use any type of glass-mount antenna with this signal booster. The outside and inside antennas must be shielded from each other to prevent oscillation.
Loading...
+ 8 hidden pages