GSM High Power
Direct Connect
800/1900 MHz
Smart Technology
Signal Booster
Contents
Before Getting Started ............................1
Accessories and Antenna Options . . . . . . . . . . . . . . . . . .1
Quick Installation Overview ........................2
Installation Diagram ..............................2
Installing the External Adapter ......................3
Installing the Outside Antenna ......................3
Installing a Wilson Electronics Signal Booster. . . . . . . . . . 3
Powering Up a Wilson Electronics Signal Booster . . . . . . 3
In-Building Installation ............................4
Warnings and Recommendations ...................5
Guarantee and Warranty ..........................6
Signal Booster Specifications . . . . . . . . . . . . . .Back Cover
Appearance of device and accessories may vary.
™
Note: This manual contains important safety and operating information.
Please read and follow the instructions in this manual. Failure to do so could
be hazardous and result in damage to your Signal Booster.
2
Installation Instructions for the Following Wilson
Electronics Signal Booster:
Model # 2B1216 FCC: PWO2B1216 IC:4726A-2B1216
The term “IC” before the radio certification number only signifies that Industry Canada
technical specifications were met.
Before Getting Started
This guide will help you properly install your Wilson Electronics Signal Booster. It is important to read through all of the installation steps for your particular application prior to
installing any equipment. Read through the instructions, visualize where all the equipment
will need to be installed and do a soft installation before mounting any equipment. For further
assistance please call our Wilson Electronics Technical Support Team: 866-294-1660.
Inside this Package
GSM
High Power
Signal Booster
Accessories & Antenna Options
Wide Band Directional Antenna
(adapters may be required)
700/2700 MHz Wide-Band Directional
Antenna (304475)
Accessory
(adapters may be required)
Lightning
Surge Protector
(859902)
Omni Directional Antennas (adapters may be required)
Magnet
Mount
(301125)
7V AC/DC
Power Supply
(859986)
(sold separately)
Mini
Magnet
(301126)
Trucker
Mount
(301101)
(301130)
800/1900
MHz Omni-
Directional
Antenna
(301202)
Marine
Antenna
6’ RG174
Cable
(951141)
NMO
Mount
(301104)
1
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
Appearance of device and accessories may vary.
or email: tech@wilsonelectronics.com Mon.- Fri. Hours: 7 am to 6 pm MST.
Quick Installation Overview
The following steps provide a summary of the Signal Booster/antenna installation process.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660.
Select a location to install the Signal Booster that is away from excessive heat, direct 1.
sunlight, moisture and that has proper ventilation. Do not place the Signal Booster in
an air-tight enclosure.
Select a location on the top of the structure to install the Outside Antenna. Use a cell 2.
phone
in test mode to find the strongest signal from the cell tower. Visit
www.WilsonElectronics.com to find test mode function for your particular cell phone.
Run the Outside Antenna cable to the Signal Booster and attach it to the connector 3.
labeled “Outside Antenna.”
An external adapter is required to connect the cell phone or cellular data card to the 4.
Signal Booster. The external adapter plugs into the included antenna extension cable
and directly into a socket on the cellular device. Run the extension cable from the
external adapter and attach it to the connector labeled “Inside Antenna” on the Signal
Booster.
Note: Be careful when plugging the connector in so as not to bend the center pins on
the connectors. Ensure all cables have a tight connection.
Before powering up the Signal Booster verify that both the Outside Antenna and the 5.
Inside Antenna are connected and check that all connections are tight. An AC surge
protector is recommended for all installations (not included).
Mini-Magnet
Installation Diagram
(Figure 1)
Antenna
Cellular Modem
GSM Hi-Power
Signal Booster
Power Supply
Powerstrip Surge Protector
NOTE: It is very important to power your Signal Booster using a surge protected AC Power Strip with at least a 1000 Joule rating.
Failure to do this will void your warranty in the event of a power surge or lightning strike.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: tech@wilsonelectronics.com Mon.- Fri. Hours: 7 am to 6 pm MST.
2
Loading...