
Contents:
How it Works ...................................1
Before Getting Started ............................1
Quick Installation Overview ........................2
Installing a Wilson Electronics Outside Antenna ........2
Installing the Low-Profile Antenna ...................3
Installing a Wilson Electronics Signal Booster. . . . . . . . . . 3
Powering Up a Wilson Electronics Signal Booster . . . . . . 4
Warnings and Recommendations ...................4
Understanding the Signal Booster Lights . . . . . . . . . . . . . 5
About Wilson Electronics ..........................6
Guarantee and Warranty ..........................6
Signal Booster Specifications . . . . . . . . . . . . . .Back Cover
Note: This manual contains important safety and operating information.
Please read and follow the instructions in this manual. Failure to
do so could be hazardous and result in damage to your Signal
Booster.
Mobile Wireless
Dual-Band
Cellular / PCS
Smart Technology ™
Signal Booster

1
Contact Wilson Electronics’s Technical Support Team with any questions at 866-294-1660
Or email: tech@wilsonelectronics.com Hours: 7am to 6 pm MST.
Installation Instructions for the Following Wilson Electronics Signal Boosters:
Mobile Wireless Dual-Band Signal Booster
Model # 271201, Part # 801201, 801212, 801215
FCC ID: PWO271201SA IC: 4726A-271201SA
Mobile Wireless Dual-Band Signal Booster
Model # 271701, Part # 801701, 801501, 801601, 801712
NOT FOR SALE IN USA / CANADA
Inside this Package
Wireless
Signal Booster
DC plug-in
power supply
(301127)
Low-Profile
Antenna
(301104)
NMO
Mount
Dual-Band
(301103)
Magnet Mount
Dual-Band
(301101)
Trucker
Mount
Tri-Band
(301113)
Mini
Magnet
Dual-Band
(301130)
Marine
Antenna
Dual-Band
How it Works
Your new Wilson Signal Booster has been carefully engineered to significantly improve the
performance of your cell phone and cellular data card in mobile applications. Together with
an outside antenna, the Signal Booster’s state-of-the-art technology is designed to increase
your signal up to 20 times, reduces dropped calls and increase data communication rates
needed for 3G technologies.
The outside antenna will collect the cell tower signal and send it through the cable to
the Signal Booster. The signal is then boosted and sent to the inside antenna. Your cell
phone or data card then communicates with the improved signal. When the cellular device
transmits, the signal goes through the inside antenna, is boosted by the Signal Booster and
broadcasted to the cell tower through the outside antenna.
Accessory Antennas
Before Getting Started
This guide will help you properly install your Wilson Electronics Dual-Band Mobile Wireless
Signal Booster. It is important to read through all of the installation steps for your
particular application prior to installing any equipment. Read through the instructions,
visualize where all the equipment will need to be installed and do a soft installation before
mounting any equipment. Contact Wilson Electronics Technical Support Team with any
questions at 866-294-1660.
(Included with
some kits)
(Included with
some kits)
Wilson Electronics manufactures a wide variety of antennas to help you customize your
Signal Booster for your specific application. Several authorized antennas are shown above.
See your dealer or visit www.WilsonElectronics.com.
(Included with
some kits)

2
Contact Wilson Electronics’s Technical Support Team with any questions at 866-294-1660
Or email: tech@wilsonelectronics.com Hours: 7am to 6 pm MST.
Warning: In a wireless installation, do
not plug the Signal
Booster directly into
the cell phone and/
or data card using an
antenna adapter. It
will damage the Signal
Booster, cell phone
and/or data card.
!
!
!
!
Outside
Antenna
Inside
Antenna
Signal
Booster
DC Power
Supply
Cell Phone
PDA
Notebook
Installation Diagram
Quick Installation Overview
Installing a Wilson Electronics Outside Antenna
To receive the best cell signal, select a location in the center of the vehicle’s roof 12 inches
away from any other antennas or windows.
Follow the specific antenna installation instructions included with the outside antenna.
Magnet - Mount
Antenna Shown
Part #301103
Carefully
Pull Down
Door Seal
Run Cable
Under Seal
Tuck Cable
Under Seal
The outside antenna must be installed
vertically. Signal performance will be
degraded if the antenna is not vertical.
The antenna cable may run through the
door to the Signal Booster.
For a more professional looking installation,
run the antenna cable under the door seal.
The antenna cable is small enough to easily
tuck under the door seal or plastic molding.
Carefully pull down the door seal. Run the
cable through the seal and push the seal
back into place. This prevents constant
wear and tear on the cable as the door
opens and closes.
Warning: Do not plug
in the DC power supply
until the outside and
inside antenna cables
are attached to the
Signal Booster.
Warning: The outside antenna must have
a separation of at least 20 inches from all
persons during normal operation.
Warning: Do not use any type of glassmount antenna with this Signal Booster.
The outside and inside antennas must
be shielded from each other to prevent
oscillation (feedback).