Wilson Electronics 271247 Installation Manual

SIGNALBOOST

™

DT

DESKTOP

SIGNALBOOST™ DT
Dual-Band
Cellular/PCS
Amplifi er System
Installation Guide

Contents:

Guarantee and Warranty · · · · · · · · · · · · · · 1
Package Contents · · · · · · · · · · · · · · · · · · · 2
Tools Required for Installation · · · · · · · · · · 2
How It Works · · · · · · · · · · · · · · · · · · · · · · · 3
Before Getting Started · · · · · · · · · · · · · · · · 4
Reasons for Weak Cellular Signals · · · · · · 4
How to Check Your Outside Signal Strength 4
Installing the Cradle Antenna · · · · · · · · · · · 5
Installing the Amplifi er Unit · · · · · · · · · · · · · 9
Powering Up the Amplifi er · · · · · · · · · · · · · 10
Understanding the Indicator Light · · · · · · · 10
Warnings and Recommendations · · · · · · · 11
Frequently Asked Questions · · · · · · · · · · · 11
About Wilson Electronics · · · · · · · · · · · · · · 12
Amplifi er Specifi cations · · · · · · · Back Cover

30-Day Money-Back Guarantee

All Wilson Electronics products are protected by Wilson’s 30- day money-back guarantee. If
for any reason the performance of any product is not acceptable, simply return the product
directly to the reseller with a dated proof of purchase.

1-Year Warranty

Wilson Electronics amplifi ers are warranted for one (1) year against defects in workmanship
and/or materials. Warranty cases may be resolved by returning the product directly to the
reseller with a dated proof of purchase.

Amplifi ers may also be returned directly to the manufacturer at the consumer’s expense, with
a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by
Wilson Electronics. Wilson shall, at its option, either repair or replace the product. Wilson
Electronics will pay for delivery of the repaired or replaced product back to the original
consumer.

This warranty does not apply to any amplifi ers determined by Wilson Electronics to have
been subjected to misuse, abuse, neglect, or mishandling that alters or damages physical or
electronic properties.

RMA numbers may be obtained by phoning Technical Support at 866-294-1660.

Installation Instructions for the Following Wilson Amplifi er:
SIGNALBOOST™ DT Dual-Band Cellular/PCS Amplifer

Model # 271247, Part # 801247

FCC ID: PWO271247SB IC: 4726A-271247SB
The term “IC” before the radio certifi cation number only signifi es that Industry Canada technical

specifi cations were met.
Operation is subject to the following two conditions: (1) This device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of
this device.

Disclaimer: The information provided by Wilson Electronics, Inc. is believed to be complete
and accurate. However, no responsibility is assumed by Wilson Electronics, Inc. for any
business or personal losses arising from its use, or for any infringements of patents or other
rights of third parties that may result from its use.

Copyright © 2007 Wilson Electronics, Inc. All rights reserved.

1

SIGNALBOOST™ DT Installation Instructions

Welcome to the Wilson Electronics Family of Products!

Thank you for purchasing the Wilson SIGNALBOOST™ DT amplifi er system. You are just minutes away
from enjoying improved performance from your cellular phone and/or laptop data card. When installed
properly, the SIGNALBOOST™ DT will signifi cantly reduce dropped calls and improve both voice and
data signal quality. By taking a few minutes to read and follow the simple instructions in this guide, you
will get the most out of your new amplifi er system. If you have questions during or after installation, please
don’t hesitate to contact a member of our Technical Support team by phone [phone] or 435-673-

5021) or email ([e-mail]). We’re here to help!

Inside this Package:

SIGNALBOOST™

DT Amplifi er

Amplifi er

Wall Bracket

On-board

Antenna

Window-Mount

(Packet A)

Antenna

and Cradle

AC Power

Supply

Wall-Mount

(Packet B)

Tools Required for Installation:

Depending on your particular installation, you will need the following tools:

• Window-mount - No additional tools needed

• Wall-mount - Drill and 3/16-inch bit, Phillips-head screwdriver

Coaxial Cable

(50 ft.)

Pole-Mount

(Packet C)

• Pole-mount - 1/4-inch open-end wrench or adjustable wrench

SIGNALBOOST™ DT Installation Instructions

2

How it Works

Your new Wilson SIGNALBOOST™ DT amplifi er system has been carefully engineered to enhance the
performance of your cell phone or cellular data card. Its advanced technology is designed to signifi cantly
improve voice and data signal quality and reduce disconnects and drop-outs.

The SIGNALBOOST™ DT works with two antennas (included). The on-board antenna communicates
with your cell phone or laptop data card, and the cradle antenna communicates with the cell tower. the
cradle antenna is designed for installation inside on a window or outside on a wall or a pole, depending on
your preferred confi guration.

Antenna

and

Cradle

Cell

Tower

Antenna

and

Cradle

Cell

Tower

Antenna

and

Cradle

Window Installation (A) Wall Installation (B) Pole Installation (C)

The cradle antenna collects the the outside signal and sends it through a cable to the SIGNALBOOST™
DT. The signal is then boosted and sent to the on-board antenna, which communicates with your cell
phone or data card. When the cell phone or data card transmits, the on-board antenna picks up the
signal and sends it to the amplifi er where it is boosted and sent through the cradle antenna to the cell
tower .

Cell

Tower

Area Needing

Increased

Signal

Wireless
Amplifier

Note: While the SIGNALBOOST™ DT is designed to give you reliable signal improvement
with the included antennas, Wilson offers a variety of optional antennas and accessories that
enable you to customize your SIGNALBOOST™ DT to your specifi c needs.
Visit www.wilsonelectronics.com for details.

3

Antenna

Option A (indoor)

Cradle Window Mount

SIGNALBOOST™ DT Installation Instructions

Antenna

Option B (outdoor)

Cradle Wall Mount

Antenna

Option C (outdoor)

Cradle Pole Mount

Before Getting Started

This guide will help you properly install Wilson’s SIGNALBOOST™ DT. It is recommended that you
read through all of the installation steps and familiarize yourself with the product. Read the

instructions and visualize where you want to place the components before mounting any equipment. If
you do not understand the instructions in full, please contact Wilson Technical Support at 866-294-1660.

Reasons for Weak Cellular Signals

Anyone who uses a cell phone or cellular data card knows the frustration of not being able to connect to
or maintain a strong cellular signal. When this occurs, it’s generally due to one of two reasons:

1. Location of the Nearest Cell Tower – Cell towers are situated to provide broad coverage; however,
there are many areas in which signal strength may be reduced by topographic features or by local
government restrictions on the height or placement of the towers themselves. Rural areas generally
have fewer cell towers than urban regions.

2. Natural and Man-made Obstructions – Signal strength can also be negatively affected by trees, hills,
buildings and other obstructions. You may be relatively close to a cell tower but still unable to make a
call. This often occurs in homes, offi ces and other buildings in which stucco, concrete or metal walls
block the signal.

Whether you’re too far from the nearest cell tower to obtain a usable signal or you’re located in an area or
building where the signal is obstructed, the Wilson SIGNALBOOST™ DT can help you get connected and
stay connected!

How to Check Your Outside Signal Strength

Before you install your SIGNALBOOST™ DT, it is very important that you determine the location of the
best available cellular signal outside your building. This will affect where you place the cradle antenna and
will help you get the best performance from your system.

Your cell phone can help you fi nd the strongest outside signal, using any or all of the following methods:

1. Place calls from several locations outside your building and note where you get the best reception.

2. Check the bar indicator on your cell phone display and note where the signal appears to be the
strongest. (Note: cell phone bars are only an approximation of signal strength and vary from phone to
phone.)

3. Using the test mode on your cell phone, move around the outside of your building and determine the
location of the strongest signal. (For assistance with the test mode on your particular phone, visit the
Technical Support section of our website: www.wilsonelectronics.com or call our Technical Support
Department at 866-294-1660 or 435-673-5021.)

Once you have determined where the outside signal is strongest, you should plan to install the cradle
antenna in that general area, either inside or outside. (See the following section for alternative
installation options.)

SIGNALBOOST™ DT Installation Instructions

4