Willoughby WODF-1-PET Operation Manual

WODF-1-PET

Installation &

Operation Manual

WODF-1-PET Series

Outdoor Pet Drinking Fountain

Table of Contents

Pre-Installation Information .....................................3

Physical Dimensions ..............................................4

Rough-In Dimensions .............................................5

Required Installation Supplies ................................6

Hardware Identifi cation Chart .................................7

Installation Instructions .............................................

Step 1: Fixture Installation .................................8

Step 2: Adjusting Drinking Spout Flow ...............9

Care and Maintenance .........................................10

Troubleshooting ....................................................11

Detail Drawings ........................................................

General Dimensions .........................................12

Exploded View w/BOM .....................................13

Rough-in Dimensions .......................................14

Freeze Resistant Valve Installation Detail ........15

Warranty ...............................................................16

Willoughby Industries, Inc.

5105 West 78th Street
Indianapolis, IN 46268
Toll Free: [phone]
Local: [phone]
Fax: [phone]
www.willoughby-ind.com

Rev. 10/2016

MADE IN THE U.S.A.

Outdoor Pet Drinking Fountain
WODF-1-PET Series

(Page intentionally left blank)

Installation & Operation Manual

Willoughby Industries, Inc. TOLL FREE [phone] ● LOCAL [phone] ● FAX [phone]

Page 2Rev. 10/2016 www.willoughby-ind.com

Outdoor Pet Drinking Fountain
WODF-1-PET Series

Installation & Operation Manual

Pre-Installation Information

Installation notice!

Check Rough-In location PRIOR to installation

Flush lines thoroughly PRIOR to hook-up

When installing the Willoughby Industries' WODF-1-PET Series fountain system:
Before Step 1 of the installation instructions, ensure that rough-ins are in the correct location.
The valve assembly, including the spray head, MUST NOT BE connected until after all lines have

been fl ushed to remove the small particles of debris that are inherent with new construction projects
and all chemicals that are used in fl ushing are purged from the system.

Chemicals used in fl ushing plumbing systems can attack the internal components of the valve and
spray head and severely damage them, so any fl ushing of the system must be followed by a full
fl ushing with pure water to clear any harsh chemicals remaining in the system. Debris in the system if
allowed to enter the valve assembly and spray head can cause poor performance or outright failure.

Again DO NOT attempt to connect the valve assembly and spray head until after all fl ushing is
complete and pure water is the only media that will be passing through the system. Damage to the
valve assembly or spray head caused by harsh chemicals or debris will not be covered by the
manufacturer's warranty.

Any fi ttings provided by the installer should be made of plastic to electrically isolate the unit from the
building or connected plumbing system.

The grounding of electric equipment such as telephones, computers, etc, to water lines is a common
procedure. This grounding can cause electrical feedback into a water fountain or similar fi xture,
causing electrolysis, which results in a metallic taste or an increase in the metal content of the water.
This can easily be avoided by using the proper materials as indicated.

Installation notice!

Check Rough-In location PRIOR to installation

Flush lines thoroughly

Willoughby Industries, Inc. TOLL FREE [phone] ● LOCAL [phone] ● FAX [phone]

PRIOR to hook-up

Page 3Rev. 10/2016 www.willoughby-ind.com

Outdoor Pet Drinking Fountain
WODF-1-PET Series

Installation & Operation Manual

Physical Dimensions- WODF-1-PET

12-1/2"

BOLT CIRCLE

9/16" THRU ALL4X

14-1/2" 4-1/4"

15-7/8"

3-13/16"

9-1/2"

7"

4-3/8"

10-3/4"

Willoughby Industries, Inc. TOLL FREE [phone] ● LOCAL [phone] ● FAX [phone]

Page 4Rev. 10/2016 www.willoughby-ind.com

Outdoor Pet Drinking Fountain
WODF-1-PET Series

Installation & Operation Manual

Rough-In Dimensions WODF-1-PET

14-1/2"

4X 9/16" THRU ALL

12-1/2"

BOLT CIRCLE

NOTE:
UNIT MUST BE DISCONNECTED AND DRAINED DURING
WINTERIZATION, PER THE FOLLOWING RECOMMENDED
PRACTICES:

SHUT OFF WATER SUPPLY TO FIXTURE (SUPPLY •
STOP AND WATER LINES BY OTHERS)
DISCONNECT AND REMOVE IN-LINE FILTER•
PRESS AND HOLD PUSHBUTTON FOR 10 SECONDS •
TO ALLOW WATER LINES TO DRAIN

VALVE ASSEMBLY DETAIL

#600285
VALVE CARTRIDGE

1/4" TUBE

CONCRETE ANCHORS

4X 1/2"-13 UNC X 4"

(BY OTHERS)

CONCRETE PAD

(BY OTHERS)

1-1/2" PVC COUPLING

(BY OTHERS)

OPEN HUB DRAIN TO BE 1-1/2" IPS

MINIMUM TO A POROUS GRAVEL FILL OR

MAIN SEWER LINE LOCATED BELOW

FROST LINE (BY OTHERS)

NOTE:
3/8" O.D. SUPPLY CONNECTION

SERVICE SHUT-OFF VALVE (BY
OTHERS)

WATER SUPPLY LINE
(BY OTHERS)

#980632
INLINE STRAINER
1/4" TO 3/8" PRESS LOCK

Willoughby Industries, Inc. TOLL FREE [phone] ● LOCAL [phone] ● FAX [phone]

Page 5Rev. 10/2016 www.willoughby-ind.com