Willoughby WICS-2222 Installation & Operation Manual

WICS-2222

Installation &

Operation Manual

WICS-2222 Series

Infection Control Sink

Table of Contents

Pre-Installation Information .....................................2

Physical Dimensions ..............................................3

Rough-In Dimensions .............................................4

Mounting Dimensions .............................................5

Checking Contents .................................................6

Required Installation Supplies ................................7

Parts List ................................................................8

Exploded-view Drawing ..........................................9

Hardware Identifi cation ........................................10

Installation Instructions .............................................

Step 1: Pedestal Mounting ...............................11

Step 2: Drain Assembly #320013 ....................12

Step 3: Basin and Pedestal Assembly .............13

Step 4: Final Assembly ....................................14

Adjustable Mixing Valve Installation..................15

Care and Maintenance .........................................16

Warranty ...............................................................17

Willoughby Industries, Inc.

5105 West 78th Street
Indianapolis, IN 46268
Toll Free: [phone]
Local: [phone]
Fax: [phone]
www.willoughby-ind.com

Rev. 9/2016

MADE IN THE U.S.A.

Infection Control Sink
WICS-2222 Series

Installation & Operation Manual

Pre-Installation Information

Installation notice!

Check Rough-In location PRIOR to installation

Flush lines thoroughly PRIOR to hook-up
When installing the Willoughby Industries' WICS-2222 Series lavatory system:
Before step 1 of the installation instructions, ensure that rough-ins are in the correct location.
The valve assembly, including the spray head, MUST NOT BE connected until after

all lines have been fl ushed to remove the small particles of debris that are inherent
with new construction projects and all chemicals that are used in fl ushing are purged
from the system.

Chemicals used in fl ushing plumbing systems can attack the internal components of
the valve and spray head and severely damage them, so any fl ushing of the system
must be followed by a full fl ushing with pure water to clear any harsh chemicals
remaining in the system. Debris in the system if allowed to enter the valve assembly
and spray head can cause poor performance or outright failure.

Again DO NOT attempt to connect the valve assembly and spray head until after all
fl ushing is complete and pure water is the only media that will be passing through the
system. Damage to the valve assembly or spray head caused by harsh chemicals or
debris will not be covered by the manufacturer's warranty.

Installation notice!

Check Rough-In location PRIOR to installation

Flush lines thoroughly PRIOR to hook-up

Willoughby Industries, Inc. TOLL FREE [phone] ● LOCAL [phone] ● FAX [phone]

Page 2Rev. 9/2016 www.willoughby-ind.com

Infection Control Sink
WICS-2222 Series

Installation & Operation Manual

Physical Dimensions- WICS-2222

Willoughby Industries, Inc. TOLL FREE [phone] ● LOCAL [phone] ● FAX [phone]

Page 3Rev. 9/2016 www.willoughby-ind.com

Infection Control Sink
WICS-2222 Series

Installation & Operation Manual

Rough-In Dimensions- WICS-2222

NOTE:

FOR INFRARED UNITS ONLY
110V GFCI REQ'D (BY OTHERS)
CONSULT LOCAL ELEC. CODES
PROVIDE 1" SPACE BETWEEN
PERIMETEROF GFCI AND FIXTURE
BACKPLATE

33 3/4" AFF

(34 MAX ADA)

1/2" HOT & COLD

WATER SUPPLIES

(BY OTHERS)

1 1/2" WASTE

(TRAP BY OTHERS)

FINISHED FLOOR

3"

C

L

1 1/2"

28 5/8"

29 1/2"

C

L

1"

"Z" CLIP

20.375

Willoughby Industries, Inc. TOLL FREE [phone] ● LOCAL [phone] ● FAX [phone]

Page 4Rev. 9/2016 www.willoughby-ind.com

Infection Control Sink
WICS-2222 Series

Installation & Operation Manual

Mounting Dimensions- WICS-2222

18-1/4"

13-1/4"

9-1/4"

4"

3-1/2"
6-15/16"

4-9/16"

2-1/2"

15-1/16"

12-9/16"

9-13/16"

Willoughby Industries, Inc. TOLL FREE [phone] ● LOCAL [phone] ● FAX [phone]

C

L

Page 5Rev. 9/2016 www.willoughby-ind.com

Infection Control Sink
WICS-2222 Series

Installation & Operation Manual

Check Contents

• Separate all parts from packaging and make sure all parts are accounted for before discarding

any packaging material. If any parts are missing, do not attempt to install the WICS-2222 Infection
Control Sink until you obtain the missing parts.

NOTE: Before beginning installation, all supply, drain and waste piping for the
WICS-2222 must be completed according to specifi ed rough-ins. If you have not received
rough-in details, please contact Willoughby Industries, Inc. [phone]

 IMPORTANT: These installation instructions
cover all of the Willoughby Industries Inc.
WICS-2222 Series. Simply omit the steps which do
not apply to the model you are installing.

 IMPORTANT: Flush all the water supply lines
before making connections.

Willoughby Industries, Inc. TOLL FREE [phone] ● LOCAL [phone] ● FAX [phone]

Page 6Rev. 9/2016 www.willoughby-ind.com