The IR T2 is shipped with Williams Sound's TFP 057 (48VDC power supply). The IR T2 is also compatible with the Williams
Sound POE 001 Power over Ethernet transformer, and with most POE switches.
Note: The IR T2 is NOT compatible with POE+ power supplies unless they are backwards compatible with POE standards.
Note: We cannot guarantee the audio quality of IR T2 units powered from a third-party POE switch, as they may introduce
noise into the system.
POE KT1
This kit should be used for applications using the power supply included with the IR T2 (TFP 057). The kit includes:
• WCA 131
• WCA 133
POE KT2
This kit should be used for applications using POE 001 or a POE Switch. The kit includes:
• WCA 131
• WCA 132
Using POE
POE is provided through a CAT5 or higher cable. Installers should carefully select the grade of CAT5 (or better) cable for the
best quality. CAT5 cable provides many advantages:
• Available pre-terminated in various lengths, or terminated on site to the required length
• Available plenum rating, if required
• Available shielded for audio applications
Williams Sound has tested control and balanced audio configurations with up to 300 ft. [91 m.] of CAT5 cable. Environmental
interference can limit the length of cable depending on how it is being used. Unbalanced audio setups in excess of 20 ft. [6
m.] of cable are not recommended.
CAT5 cable contains four twisted pairs of wires, two of which are used for POE. Using Williams Sound's passive POE injector
kits (POE KT1 or POE KT2) allows the installer to use the remaining two pairs of wire for one of the following three options:
• 1 channel of balanced line level audio
• 1 or 2 channels of unbalanced line level audio
• RS-232 control and monitoring signal
If using 2 channels of balanced line level audio, control/monitoring, and power, POE KT1 or POE KT2 will need to be used
along with an additional CAT5 cable. One CAT5 cable will be connected to the POE injector kit and provide power and
control, while the other CAT5 cable will provide audio.
Page 2
Input Diagrams
TFP 057
48VDC
International
Power
Supply
WCA 133
CAT5 Cable
To Control or Audio Inputs,
See Figures 3-5 for wiring.
CAT5 Cable
WCA 132
POE Switch
POE 001 48VDC
POE Power Supply
LAN + DCLAN
To Control or Audio Inputs,See Figures 3-5 for wiring.
OR
Figure 1: POE Input Setup using WCA 133 Adapter Cable and the TFP 057 power supply.
LAN + DCLAN
OR
POE Switch
POE 001 48VDC
POE Power Supply
To Control or Audio Inputs,
See Figures 3-5 for wiring.
WCA 132
Figure 2: POE Input Setup using WCA 132 Adapter Cable and the POE 001 or a third party POE Switch.
Cabling for Inputs
If using the POE 001 power over Ethernet injector, connect either the RJ-45 plug on the WCA 132 or a CAT5 cable directly to the port
labeled LAN + DC (See Figure 2).
Note that the WCA 132 can be plugged directly into the LAN port, which may not leave enough of a cable run to connect to the audio
In all the figures below, check the color coding for the type of CAT5 cable used to determine wire colors if terminating a CAT5 cable.
CAT5 Cable
Input Wiring
Note: The figures below are shown using a WCA 133, but a WCA 132 can be used with the same wiring. In some cables, the yellow wire may
be colored green.
5
9
4
8
3
7
2
6
1
Black - GND
Yellow - GND
White - RX
Red - TX
Figure 3: RS-232 Control Input
WCA 133
2
Page 3
WCA 133
1
2
3
Red (In Phase, +)
White (Signal, -)
Yellow (GND)
Black (GND)
1
2
3
WCA 133
1
1
2
2
3
3
Black (Ch B, GND)
Yellow (In Phase, Ch B+)
White (Ch A GND)
Red (In Phase, Ch A +)
3
2
1
3
2
1
Output Diagrams
CH B
CH A
TFP 05748VDCInternationalPowerSupply
WCA 133
CAT5 Cable
To Control or Audio Inputs,See Figures 3-5 for wiring.
CAT5 Cable
WCA 132
POE Switch
POE 001 48VDC
POE Power Supply
LAN + DCLAN
To Control or Audio Inputs,See Figures 3-5 for wiring.
OR
Figure 4: Balanced Line Level Audio for Input
Figure 5: Unbalanced Line Level Audio for Input
Power In
Line Level
Audio In
Line Level
Audio In
Control RS-232
TX/RX/GND
WCA 131CAT5 Cable
To Phoenix connectors for audio
or control, see Figures 7-9 for
wiring.
Figure 6: POE Output Setup using a WCA 131 Adapter Cable and the IR T2 back panel.
3
Page 4
Output Wiring
WCA 131
GND
TX
RX
Figure 7: RS-232 Control Output
Pin 1 - Red - TX
Pin 2 - White - RX
Pin 3 - Yellow - GND
Pin 6 - Black - GND
To Control
PLG 027
(included)
GND
TX
RX
WCA 131
WCA 131
+
GND
-
Figure 8: Balanced Line Level Audio Output
+
GND
-
+
GND
-
Figure 9: Unbalanced Line Level Audio Output
Red (In Phase, +)
White (Signal, -)
Yellow (GND)
Black (GND)
To Ch A or Ch B
Line Level Audio In
Line Level Audio In
Red (In Phase, Ch A +)
White (Ch A GND)
Yellow (In Phase, Ch B+)
Black (Ch B, GND)
Line Level Audio In
+
GND
-
To Ch A
+
GND
-
+
GND
-
To Ch B
4
Page 5
Connecting Audio, Power and Control
Power and Control Setup
Providing power, audio and control options simultaneously requires two CAT5 cable runs. To run the power and control, you
will need either the POE KT1 or POE KT2, depending on how you wish to power the device.
If you are using the provided power supply (TFP 057), connect the power to a WCA 133 from POE KT1.
If you are using POE switch or power supply, connect the power to a WCA 132 from POE KT2.
When powering the IR T2, connect the WCA 131 to the CAT5 cable with the powered WCA 132 or WCA 133. Connect the WCA
131 to the Power In and Control inputs on the IR T2.
Run a separate CAT5 (or higher) cable connected to a balanced audio source on one end. Connect the other end to the IR
T2 following the wiring diagram below.
Refer to the wiring diagrams throughout this document for your specific configuration needs.
LAN + DCLAN
POE 001 48VDC
POE Power Supply
TFP 057
48VDC
International
Power
Supply
a TFP 057 power supply or POE power supply or switch.
Choose one power source:
Connections to the IR T2
RS232 Control and Power
(see Power and Control Setup)
CAT5 Cable (Powered)
Balanced Audio for CH A and CH B
Red (In Phase, Ch A +)
2
1
1
3
2
3
White (Ch A GND)
Yellow (In Phase, Ch B+)
Black (Ch B, GND)
POE Switch
RS232 Control
OR
RS232 Control
Two CAT5 cables need to be run to the IR T2
WCA 131
2
3
2
3
Connect the chosen power source to the matching cable power connection.
Wire this input for Control.
Connect to Power
CAT5 Cable (Unpowered)
WCA 132
WCA 133
CAT5 Cable
CAT5 Cable
Connect Control to the powered cable.
CH B
CH A
Power In
Line Level
Line Level
Audio In
Audio In
Red (In Phase, Ch A +)
White (Ch A GND)
Yellow (In Phase, Ch B+)
Black (Ch B, GND)
Control RS-232
TX/RX/GND
To Ch A
Line Level Audio In
To Ch B
Line Level Audio In
To IR T2
+
GND
+
GND
-
Note: Use of this product with power supplies not provided by the manufacturer voids the warranty of the product (see IR T2
user guide [MAN 217] for further details about warranty coverage).
For additional technical support, please contact TechBlue by calling +1-800-328-6190 or visit www.williamsav.com.