Williams Sound IC-1 User Manual

Page 1
Interpreter ’s Control Center, Model IC-1
Williams Sound
®
Helping People Hear
Description:
Interpreter Control Center, Model IC-1:
Dimensions,Weight: 7" (17.7 cm) W x 5.625" (14.3 cm) D x 3.125" (9.3 cm) H, 1.82 lbs (.83 kg) Color: Beige epoxy paint with black legends, blue bottom and side panels Power: External power supply, 12 VAC, 50 or 60 Hz, 10 VA, (TFP 008 Power Supply)
(A 240 VAC Power Supply is also available, TFP 008 HV)
INPUTS
Floor In, Relay In:
1/4" Microphone Inputs: Left and right, 1/4" TRS phone jack, balanced or unbalanced mic-level,
3.5 mm Microphone Inputs: Left and right, 3.5 mm TRS phone jack, unbalanced (T,S) for condenser mics,
OUTPUTS
Key Out, Norm Out:
Phones: 3.5 mm TRS phone jack, mono or stereo headphone, 8-32
CONTROLS
Volume: Left and right, rotary, controls headphones volume
Mic Switch: 3–way toggle. Selects left mic, right mic, or both. Mute Switch: Push button. Mutes left and right mics when depressed. Function Switch: 4-way push button. Selects OFF, NORM, RELAY, or KEY modes.
OFF Mode: Floor input (FLOOR IN) is fed to the interpreter’s headphones to allow monitoring of the meeting.
NORM Mode: Floor input (FLOOR IN) is fed to the interpreter’s headphones. The selected interpreter’s microphone
RELAY Mode: Interpreter monitors the relay input (RELAY IN) while the selected microphone feeds the normal output (NORM OUT) KEY Mode: Used to feed a second language audience. The interpreters monitor the floor input (FLOOR IN)
eedthru Jumpers:
F
J1 Feeds the floor signal to the normal output (NORM OUT) J2 Feeds the floor signal to the key output (RELA
Recommended Micr
MIC 079
ON Indicator Light: Green LED, glows when power is applied to the transmitter. There is no on/off switch.
anty:
r
ar
W
ophone
3-Pin XLR female jack, balanced or unbalanced line-level, max. 3.8 Vrms, Gain 6 dB, 43 kΩ input impedance
max. 70 mVrms, gain 46 dB, supplies simplex DC power for electret mics,
1.75 kΩ input impedance
max. 70 mVrms, gain 46 dB, supplies DC power on tip, 1.75 kinput impedance
3-Pin XLR male jack, balanced or unbalanced line-level, 7.7 max. Vrms, 56 Ω source impedance
,
63.7 mW at 8 load max
Interpreter’s microphones are muted.
is fed to the normal output (NORM OUT).
while mics feed the key output (KEY OUT). Located on bottom of cabinet. Used to select floor signal feedthru options.
Y OUT)
Dual headphone, condenser mic, 3.5 mm plug (MIC 079), Audio Indicator Light: Yellow LED, flashes when audio signal is present
The T17 is designed to be left on continuously. 3 years, parts and labor*
*90 day warranty on accessories NOTE: SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE!
©2005, Williams Sound Corp. CAT 063C
1
Page 2
Interpreter ’s Control Center, Model IC-1
Williams Sound
®
Helping People Hear
Right Volume
0
1
2
4
5
6
3
Off Norm Relay Key
IC-1 Interpreter's Control Center
Left Volume
0
1
2
4
5
6
3
Left Right
L+R
Microphone
Mute
Williams Sound
®
IC–1 Top Panel
Microphone
Mic Phones L
MicPhonesR
Microphone
IC–1 Front Panel
Interpreter's Control Center
Model IC-1
Floor In Norm Out Key Out Relay In
Power
12 VAC
Williams Sound Corp.
Made in U.S.A.
IC–1 Rear Panel
Two
Channel Infrared System Modulator Williams Sound
Power
Phones
+9 +6 +3 0
-3
-6
-9
-
12
-
15
-
18
+9 +6 +3 0
-3
-6
-9
-
12
-
15
-
18
3.8
3.3
2.8
2.3
Level
5
0
1
2
3
46
7 8 9
10
Level
5
0
1
2
3
46
7 8 9
10
Compress
3.8
3.3
2.8
2.3
Compress
Inputs Mixed
Stereo
IR
CH A
CH B
Frequency
(MHz)
Frequency
(MHz)
Channel A
Channel B
Microprocessor Controlled Frequency Synthesized
IC-1 Interpreter's Contr
ol Center
Microphone
Mute
Left Volume Right Volume
Williams Sound
IC-1 Interpreter's Contr
ol Center
Microphone
Mute
Left Volume
Right Volume
Williams Sound
IC-1 Interpreter's Control Center
Microphone
Mute
Left Volume Right Volume
Williams Sound
IC-1 Interpreter's Control Center
Microphone
Mute
Left Volume
Right Volume
Williams Sound
Two
Channel Infrared System Modulator Williams Sound
Power
Phones
+9 +6 +3 0
-3
-6
-9
-
12
-
15
-
18
+9 +6 +3 0
-3
-6
-9
-
12
-
15
-
18
3.8
3.3
2.8
2.3
Level
5
0
1
2
3
46
7 8 9
10
Level
5
0
1
2
3
46
7
8
9
10
Compress
3.8
3.3
2.8
2.3
Compress
Inputs Mixed
Stereo
IR
CH A
CH B
Frequency
(MHz)
Frequency
(MHz)
Channel A
Channel B
Microprocessor Controlled Frequency Synthesized
MOD 232 Modulator
Pod
ium
(Floor)
Mixer
Distribution
Amp
IC-1
Interpreter #1Interpreter
#2
Interpreter #3Interpreter
#4
IC-1
IC-1
IC-1
MOD 232 Modulator
RX12-4 Receiver
TX9 Emitter
Input CHA
Baseband
Input
Baseband
Output
Input CHB
Norm Out
Floor In
Mic
Mic
Mic
Mic
Floor In
Floor In
Floor In
Norm Out
Norm Out
Norm Out
Input CHA Input CHB
Coaxial
Cable
4 chann
el
IR
Williams Sound
4 channel
IR
Williams Sound
NOTE: SPECIFICA
©2005, Williams Sound Corp. CAT 063C
TIONS SUBJECT
TO CHANGE WITHOUT NOTICE!
2
Page 3
Interpreter ’s Control Center, Model IC-1
Williams Sound
®
Helping People Hear
Bid Specs
The unit shall be 7 inches wide, 5 5⁄8 inches deep and 3 1⁄ 8 inches tall. The unit shall weigh 1.82 lbs. The module shall be painted beige with black legends indicating controls, inputs and outputs. The bottom and side panels shall be painted blue. The power supply shall be external, 12 VAC, 50 or 60 Hz, 10 VA. An optional 240 VA C Power Supply shall also be available. Inputs shall be configured as follows: The “Floor In” and “Key In” inputs shall be 3-Pin, XLR female jacks, allowing balanced or unbalanced line-level inputs. Maximum input levels shall be 3.8 Vrms. Gain shall be 6 dB with 43 kΩ input impedance. There shall be two microphone inputs, both 1⁄4" TRS phone jacks, bal- anced or unbalanced. These inputs shall be mic-level, allowing a maximum 70 mVrms and 46 dB gain. The two microphone inputs shall supply simplex DC power for electret mics with 1.75 kinput impedance. There shall be two independent 3.5 mm TRS microphone inputs (unbalanced [T,S] for condenser mics), allowing a maximum 70 mVrms. Gain shall be 46 dB. The two 3.5 mm inputs shall supply DC power on tip, 1.75 kinput impedance.
Outputs
The “Key Out” and “Norm Out” outputs shall be 3-Pin XLR male jacks, balanced or unbalanced line-level. Maximum output shall be 7.7 Vrms. Source impedance shall be 56 . There shall be two independent 3.5 mm TRS headphone output jacks (left right). The headphone outputs shall allow the use of either mono or stereo head­phones, 8-32 . Maximum power shall be 63 mW at 8 Ω.
Controls
The unit shall have two, independent rotary-type volume controls, controlling headphone volume. The “Microphone” switch shall be a 3–way toggle type, selecting left mic, right mic or both. The mute switch shall be a push button-type, muting left and right mics when depressed. The function switch shall be a 4-way push button­type, selecting OFF, NORM, RELAY or KEY modes.
Controls
Feedthru jumpers used to select floor signal feedthru options shall be located on bottom of cabinet.The unit shall be Williams Sound Corp. Interpreter Control Center, model IC-1.
NOTE: SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE!
©2005, Williams Sound Corp. CAT 063C
3
Page 4
Interpreter ’s Control Center, Model IC-1
Williams Sound
®
Helping People Hear
Contact:
United States and Mexico
Williams Sound Corp. 10321 W. 70th Street Eden Prairie, MN 55344-3446 Ph: 800-328-6190 / 952-943-2252 / FAX: 952-943-2174 Web: www.williamssound.com Email: info@williamssound.com
Canada
Thorvin Electronics 2861 Sherwood Heights Dr. Units 36-37 Oakville, ON L6J-7K1 Canada Ph: 800-323-6634 / 905-829-3040 / FAX: 905-829-4196 Web: www.thorvinelectronics.com
South America
DPTech SIA Trecho 3/4 Lote 335 2°. Andar 71200-030 Brasília, DF BRAZIL Ph: (5561) 361-1384 Fax: (5561) 361-0948 Web: www.dptech.com.br Email: ws@dptech.com.br
Europe and Asia
International Sales Department Williams Sound Corp. 10321 W. 70th Street Eden Prairie, MN 55344 USA Phone: +1 952 943 2252 Fax: +1 952 943 2174 Email: doreeni@williamssound.com Web: www.williamssound.com
©2005, Williams Sound Corp. CAT 063C
4
Loading...