Williams Sound DWD 102 Users Manual
DWD 102
Digi-Wave™ Dual-Bay Docking Station
User manual
Compatible with Digi-Wave™ Models:
DLT 100 2.0, DLR 60 2.0 and DLR 60
MAN 180C
System Overview
Thank you for purchasing the DWD 102 Digi-Wave™ Dual-Bay Docking
Station.
The Digi-Wave™ Dock, when used with second-generation Digi-Wave 2.0
products, can be used to receive audio through a Digi-Wave™ receiver (or
transceiver) and send the audio into a sound system, or send audio from a
sound system to a transceiver for broadcast. There are many applications for
the dock; for more information please visit our website and download the Digi-
Wave Dock Applications Guide.
The Digi-Wave™ Dock supports audio input/output functions with the DLT 100
2.0, DLR 60 2.0 and DLR 60 models. It will only act as a charger for the DLT
100.
System Includes
(1) DWD 102 Digi-Wave™ Dual-Bay Docking Station.
(1) TFP 048 Power Supply
(1) WLC 004 Line Cord (U.S.)
(2) WCA 078 Stereo RCA Cables
(4) RBP 005 Support Pads 1/8” (thick)
(4) RBP 006 Support Pads 1/16” (thin)
Recycling Instructions
Help Williams Sound protect the environment! Please take the time to dispose
of your equipment properly.
Product Recycling for Customers in the European Union:
Please do NOT dispose of your Williams Sound equipment in the
household trash. Please take the equipment to an electronics
recycling center; OR, return the product to the factory for proper
disposal.
Battery Recycling for Customers in the European Union:
Please do NOT dispose of used batteries in the household trash.
Please take the batteries to a retail or community collection point
for recycling.
2
Connectors and Controls
Figure 1: Rear View
Bay 2Bay 1
XLR
RCA
XLR
Line
Input
Bay 2
RCA
Line
Inputs
Bay 2
Figure 2: Top View
Line
Output
Bay 2
Line
Outputs
Bay 2
Auto/
Manual
Switch
Bay 2
Connector
Power
Supply
Auto/
Manual
Switch
Bay 1
XLR
Line
Input
Bay 1
RCA
Line
Inputs
Bay 1
XLR
Line
Output
Bay 1
RCA
Line
Outputs
Bay 1
Bay 1 Bay 2
Power Indicator LED
3
Setup Instructions:
1. Connect the external devices to the XLR or RCA jacks on the back of
the Digi-Wave™ Dock (Figure 1). Both RCA and the single XLR input
jacks are all mixed internally - but for proper mixing to occur at the output
without any adjustments, the following combinations can be used: One
single RCA jack by itself, both RCA jacks, the XLR jack by itself, or both
RCA jacks and the XLR jack. If one RCA jack is to be mixed with the XLR
jack, the gain of the RCA source will need to be adjusted at the source.
2. Select DLT mode. We recommend using “Chairman Master” mode for
two reasons: (1) The Chairman Master has #1 Talk Priority so the Talk
button on this unit can never be bumped o by another user, and (2)
The Chairman Master will be powered by the dock, and all other units
synchronize to the Chairman Master, making it a more reliable Master
than one powered from the internal battery.
3. Insert any combination of DLT 100 2.0 transceiver(s) or DLR 60 2.0
receiver(s) into the bays (Figure 2). The unit(s) must be facing forward for
proper mating to the 30-pin connector.
4. Using the appropriate line cord (US, EURO, UK or AUS) into the TFP 048,
plug the TFP 048 power supply into the AC wall outlet. Plug the power
connector into the rear of the DWD 102 unit (gure 1). The green LED
power indicator should light up (Figure 2).
5. Select either Auto or Manual for each docked device, using the switch(es)
on the back. See Figure 3 for an explanation of the dierence between
the two modes.
You may charge any combination of DLT 100 2.0, DLT 100, DLR 60 2.0, or
DLR 60s. (In DLR 60 2.0 and DLR 60 units, NiMH batteries must be used and
the battery switch must be in the NiMH position.) Digi-Wave™ Dock audio
inputs/outputs are only available on the DLT 100 2.0, DLR 60 2.0, and DLR
60. DLT 100s can be docked but will charge only (no audio). See Digi-Wave™
Dock Functions chart (Figure 3).
Note: It is safe to leave the DLT and DLR units in the charger, even after
the batteries are fully charged. The charger will switch to ‘maintain’
mode to maintain full battery potential.
4
Loading...