Page 1
Digi-Wave
SYSTEM EXAMPLES
™
Dock Application Guide
© 2019, Williams AV, LLC TCH 009D
Page 2
Digi-Wave Dock Application Guide
Table of Contents
Purpose of this Guide 3
Base Station Transmitter 4
Base Station Receiver 6
Teleconferencing 8
Range Extender 10
Interpretation with Wireless Presenter 12
Two-Way, Two-Language Question and Answer 14
5 Simultaneous Talkers with a 2.0 System 17
Extending a 2.0 Series system with 300 Series Product 20
2
Page 3
Digi-Wave Dock Application Guide
Purpose of this Guide
The Digi-Wave Dock provides a way to:
(a) connect Digi-Wave wireless product to a hard-wired system,
(b) hard-wire wireless product together, and
(c) charge Digi-Wave DLTs and/or DLRs
This guide is designed to present various ways the Digi-Wave Dock can be utilized. The dock is a versatile piece of equipment, and the
following examples are by no means exhaustive. These examples are provided as a starting point for more creative or complex uses.
“DLT” in this guide refers to DLT 300 or DLT 100 2.0.
“DLR” in this guide refers to DLR 60, DLR 60 2.0 or DLR 360.
Note: The DLT 100 and DLR 50 units do not have active audio pins to send or receive audio through the 30-pin connector on the Dock. So
these units cannot be used in any of the scenarios described in this guide. The DLT 100 can be charged in the dock (only).
Cannot be used in any scenarios this guide:
DLT 100
DLR 50
Can be used in applicable scenarios in this guide:
DLT 300
DLT 100 2.0
DLR 360
DLR 60 2.0
DLR 60
3
Page 4
Digi-Wave Dock Application Guide
Base Station Transmitter
The Digi-Wave Dock can be used as a method of transmitting audio from a sound system to the audience listening with transceivers or
receivers.
How it works:
An audio program, presenter’s voice, etc. is sent from a sound system or other equipment to the dock line input. The dock delivers the
audio to the docked transceiver which broadcasts the audio out to receivers (or transceivers) in the audience.
Required Equipment:
One Digi-Wave Dock, one DLT 300 Transceiver
4
Page 5
Digi-Wave Dock Application Guide
An audio program, speakers voice, etc. is sent from a sound system or other equipment to the dock input. The dock delivers the audio to the docked
transceiver which broadcasts the audio out to receivers (or transceivers) in the audience.
Unit Programming for Base Station Transmitter
Unit
Location
Docked *
Audience DLR 360 - - 01 0
Model Mode Priority Group Channel
DLT 300
1-way - Main Speaker:
Master
01 0
* Docked DLT must have it’s bay switch set to “Auto”. This keeps the battery charged and locks the TALK button on. When
the Dock gets powered up the DLT will begin transmitting automatically. When listeners enter the room, their receivers (or
transceivers) will sync to the docked unit and begin receiving audio.
Audience
Presenter
Sound System,
Analog Mixer, etc.
DLT Programming:
Mode:
Priority:
Group: 01
Channel: 0
Talk Mode: PnL
Talk Button: ON
Analog Line Input
(XLR or RCA)
Analog
Line Output
(XLR or RCA)
Docked
DLT
DLR Programming:
Group: 01
Channel: 0
Digi-Wave Dock
(rear)
Dock Bay Switch
set to “Auto”
5
Page 6
Digi-Wave Dock Application Guide
Base Station Receiver
The Digi-Wave Dock can be used to receive audio from a DLT, and send this audio into a sound system. Utilized in this way, a presenter
can be recorded, heard by the audience using receivers, or heard by the audience through loudspeakers.
How it works:
A presenter’s voice is transmitted from a DLT 300 transceiver to a docked DLR 360 receiver. The dock sends the audio through it’s line
outputs into a sound system or other equipment.
Required Equipment:
One Digi-Wave Dock, one DLR 360 Receiver
6
Page 7
Digi-Wave Dock Application Guide
A speaker’s voice is transmitted from a DLT 100 2.0 to a docked DLR 60 2.0 receiver (or DLT 100 2.0
transceiver). The dock sends the audio through it’s outputs into a sound system or other equipment.
Base Station Receiver
Unit Programming
Unit
Location
Presenter
Docked *
*The docked DLR should have it’s bay switch set to “Auto”; this keeps it powered up and it will begin receiving when the dock
powers up and the Master is found.
The presenter’s DLT should be set to 1-way mode-Main Speaker/Master; this way when the presenter enters the room, the docked receiver
(or transceiver) will sync with the presenter’s DLT and begin receiving the audio, automatically.
Using a docked receiver is recommended for simplicity, but if using a docked DLT, it should be set to 2-way Slave mode. This will not work
if the docked DLT is in one-way mode.
Model Mode Priority Group Channel
DLT 300
1-way - Main Speaker:
DLR 360 - -
Master
01 0
01 0
Presenter
DLT Programming:
Mode:
Priority:
Group: 1
Channel: 0
Talk Mode: PnL
Talk Button: ON
Docked
DLR
Digi-Wave Dock (rear)
DLR Programming:
Group: 01
Channel: 00
Analog Line Output
(XLR or RCA)
Analog Line Input
(XLR or RCA)
Dock Bay Switch
set to “Auto”
The Audience hears the
Presenter through the
Sound System
Sound System
7
Page 8
Digi-Wave Dock Application Guide
Teleconferencing
The dock provides full duplex audio capability when a DLT Transceiver is docked. Utilized in this way, two-way communication can be
established between two conference rooms, with audio sent/received over the internet. People on both sides can speak/listen with
DLT transceivers, or just listen with DLR receivers. A program such as Skype or other teleconference software can be used to make the
conference call over the internet. The two-way audio from each dock is connected to the computer in that conference room, and the audio
from the dock is routed into a sound system in that room. Additional DLTs can be added for hearing assistance, asking and answering
questions, or for presentations where a person will be standing or walking.
How it works:
In Conference Room 1, people’s voices are picked up using the internal microphone* on a portable DLT on the conference room table.
This audio is transmitted to a docked DLT. The dock sends the audio through it’s outputs to a computer. The computer sends the audio
through the internet where it is received by a computer in Conference Room 2. The computer in Conference Room 2 sends its audio to a
sound system for people in Conference Room 2 to hear. Additional DLTs can be used for hearing assistance or Q&A.
In the same manner, audio is sent from Conference Room 2 to Conference Room 1. Typically this type of system is coupled with a video
screen in each conference room, so the people in both locations can see each other.
*a conference microphone could also be used for improved pickup of multiple voices (not shown)
Required Equipment:
Two Digi-Wave Docks, four DLTs, four 3.5mm to RCA cables, conference microphone if desired
Conference Room 1
Conference Room 2
COMPUTER
POWER
VOLUME
POWER AMPLIFIER
POWER HEADPHONE
COMPUTER
POWER
VOLUME
POWER AMPLIFIER
POWER HEADPHONE
8
Page 9
Digi-Wave Dock Application Guide
In Conference Room 1, a speaker’s voice is transmitted from a DLT 100 2.0 to a docked DLT 100
2.0. The dock sends the audio through it’s outputs into a computer. The computer sends the
audio through the internet where it is received by a computer in Conference Room 2. The
computer in Conference Room 2 sends its audio to a dock that has a docked DLT 100 2.0
transceiver. A listener with a DLT or DLR in Conference Room 2 hears the audio from Conference
Room 1.
In the same manner, audio is sent from Conference Room 2 to Conference Room 1, completing
the 2-way communication circuit. Typically this type of system is coupled with a video screen in
each conference room, so the people in both locations can see and hear each other (not shown).
Teleconferencing
Unit Programming
Unit
Location
Docked *
Conf Rm 1
Presenters
Conf Rm 1
Docked *
Conf Rm 2
Presenters
Conf Rm 2
Model Mode Priority Group Address
DLT 300
DLT 300
DLT 300
DLT 300
2-way:
2-way:
2-way:
2-way:
Master 1
Guest
Master 1
Guest 1
1 01
1
02 ... 99**
1 01
02 ... 99**
* Docked DLT must have it’s bay switch set to “Auto”. This keeps the battery charged and locks the TALK button on. When
the Dock gets powered up the DLT will begin transmitting automatically. When listeners enter the room, their receivers (or
transceivers) will sync to the docked unit and begin receiving audio.
** Each DLT transceiver within a Group must have a unique address.
Conference Room 1 and 2 are separated by a large enough physical distance that both rooms are out of range of each other’s Digi-Wave
System. This eliminates the need to have each system on separate groups, so they can both use Group 1.
Main Presenter
Conf. Rm. 1
CONFERENCE ROOM 1 CONFERENCE ROOM 2
Main Presenter
Conf. Rm 2
DLT Programming:
Mode:
Priority:
Group: 1
Address: 2
Talk Mode: PnL
Talk Button: ON
Additional people
in the room
can join the
conference
with transceivers
in this same
configuration
(must have
addresses
03...99)
unique
Docked
DLT
Line Input
(RCA)
Line Output (3.5mm stereo)
DLT Programming:
Mode:
Priority:
Group: 1
Address: 1
Talk Mode: PnL
Talk Button: ON
Dock-
Bay-
Switch
set to
“Auto”
Line Input
(3.5mm stereo)
Desktop
Computer
Digi-Wave Dock
(rear)
Line
Output
(RCA)
Digi-Wave Dock
Conf Rm 1 Audio
INTERNET
Conf Rm 2 Audio
DLT Programming:
Mode:
Priority:
Group: 1
Address: 1
Talk Mode: PnL
Talk Button: ON
Dock-
Switch
set to
“Auto”
(rear)
Line Output
(3.5mm
stereo)
Bay-
Line Input
(RCA)
Docked
DLT
Line Input
(3.5mm stereo)
Desktop
Computer
Line
Output
(RCA)
DLT Programming:
Mode:
Priority:
Group: 1
Address: 2
Talk Mode: PnL
Talk Button: ON
Additional people
in the room
can join the
conference
with transceivers
in this same
configuration
(must have
addresses
03...99)
unique
9
Page 10
Digi-Wave Dock Application Guide
Range Extender
The Digi-Wave Dock can be used to extend the range of an existing Digi-wave System - for reaching a larger audience, reaching
audiences in additional rooms or areas, or for establising two-way communication that is outside the normal range of wireless operation
(shown).
How it works:
In Building A, a talker’s voice is transmitted from a handheld DLT to a docked DLT. The dock sends the received audio through it’s output,
through the first XLR cable, to the input of a second dock in Building B. The second dock has a DLT transceiver that broadcasts the audio
to a person listening with a handheld DLT. When the person in Building B speaks, audio travels from the handheld DLT, to the docked DLT,
and back along a second XLR cable to Building A where it enters the first dock’s input, completing a two-way communication path. The
length of the range extension is limited by the type of XLR cables used, but can be as much as 500 feet or even much more.
Required Equipment:
Two Digi-Wave docks, two long XLR cables, and 4 DLT Transceivers
Handheld
DLT
Docked
DLT
Docked
DLT
Building B
(2) XLR cables
Building A
Distance = 500 ft or more
Handheld
DLT
10
Page 11
Digi-Wave Dock Application Guide
Range Extender
Unit Programming
Unit
Location
Docked *
Area/Rm 1
Presenter
Area/Rm 1
Docked *
Area/Rm 2
Presenter
Area/Rm 2
Model Mode Priority Group Address
DLT 300
DLT 300
DLT 300
DLT 300
2-way:
2-way:
2-way:
2-way:
Master 1
Guest
Master 1
Guest 1
1 01
1
02 ... 99*
1 01
02 ... 99*
* Docked DLT must have it’s bay switch set to “Auto”. This keeps the battery charged and locks the TALK button on. When
the Dock gets powered up the DLT will begin transmitting automatically. When listeners enter the room, their receivers (or
transceivers) will sync to the docked unit and begin receiving audio.
** Each unit within a Group must have a unique address.
Area/Room 1 Area/Room 2
AREA / ROOM 1
Presenter
DLT Programming:
Mode:
Priority:
Group: 1
Address: 1
Talk Mode: Ptt or PnL
Talk Button: ON
ANALOG
LINE
INPUT
(XLR)
Docked
DLT
in 2-way
Master
Chaiman
mode
DLT Programming:
Mode:
Priority:
Group: 1
Address: 1
Talk Mode: PnL
Talk Button: ON
Bay switch
set to “Auto”
Digi-Wave Dock
(rear)
ANALOG
LINE
OUTPUT
(XLR)
DLT Programming:
Distance = 500 feet or more
Mode:
Priority:
Group: 1
Address: 1
Talk Mode: PnL
Talk Button: ON
Digi-Wave Dock
Bay switch
set to “Auto”
(rear)
ANALOG
LINE
INPUT
(XLR)
Docked
DLT
in 2-way
Master
Chaiman
mode
AREA / ROOM 2
Presenter
ANALOG
LINE
OUTPUT
(XLR)
DLT Programming:
Mode:
Priority:
Group: 1
Address: 1
Talk Mode: Ptt or PnL
Talk Button: ON
11
Page 12
Digi-Wave Dock Application Guide
Interpretation with Wireless Presenter
The Digi-Wave Dock can be used to easily connect an IC-2 Interpreter’s console and provide a wireless transceiver for the main presenter
(floor). The audience hears the interpreted language (from the IC-2 console) on Channel 1, or the original presenter on Channel 0.
How it works:
The main presenter’s voice (i.e. English) is transmitted from a portable DLT in 1-way mode on Ch. 0, to a docked DLT in Interpreter Mode
on Ch. 1. The dock sends the presenter’s voice through an XLR cable to the Floor input on the IC-2. The interpreter hears the presenter’s
voice and interprets into Spanish. Spanish comes back from the IC-2 to the Dock on an XLR cable. The docked DLT broadcasts the
interpreter’s voice to the audience listening with DLR receivers on Channel 1.
Additional languages (Channels 2-14) require daisy-chaining additional IC-2’s and additional Dock Bays, one for each interpreted language.
In this example just the first interpreted language/IC-2/dock is shown.
Note that this “Floor-In” method need only be connected on the first IC-2 when daisy-chaining a system, as the floor will be carried on the
bus to each IC-2 in the chain.
Required Equipment:
One Digi-Wave dock, one IC-2 Interpreters Console, 2 DLT Transceivers, 2 XLR cables, audience DLRs as required.
12
Page 13
Unit
Location
Digi-Wave Dock Application Guide
Interpretation with Wireless Presenter
Unit Programming
Model Mode Priority Group Channel
Docked *
DLT 300
1-way - Interpreter:
Guest 1 0
Wireless
Presenter
DLT 300
1-way - Main Speaker:
Master 1 1
Ch. 0
Audience
Members
DLR 360 - - 1 0-14
* Docked DLT must have it’s bay switch set to “Auto”. This keeps the battery charged and locks the TALK button on. When
the Dock gets powered up the DLT will begin transmitting automatically. When listeners enter the room, their receivers (or
transceivers) will sync to the docked unit and begin receiving audio.
The Audience listens to the Floor or interpreted channels. Docked unit is Ch. 1-14, one channel per language.
Wireless Presenter
Audience hears English on Ch. 0 from portable DLT
or Spanish on Ch. 1 from docked DLT
Audience
DLR Programming:
Group: 01
Channel: 00 English,
or 01 Spanish
Docked DLT
DLT Programming:
Mode:
Priority:
Group: 1
Channel: 0
Talk Mode: PnL
Talk Button: ON
DLT Programming:
Mode:
Priority:
Group: 1
Channel: 1
Talk Mode: PnL
Talk Button: ON
Analog
Line Input
(XLR)
Analog
Line Output
(XLR)
Dock Bay Switch
set to “Auto”
Digi-Wave Dock (rear)
Interpreter’s Voice (Spanish)
Main Presenter (English)
13
IC-2 (rear)
Analog
Line Output
(XLR)
Analog
Line Input
(XLR)
Page 14
Digi-Wave Dock Application Guide
1. Question
asked in
English
Moderator
listening
not speaking
Interpreter
Audience hears all
Questions and Answers
in their Language
2. Question
interpreted
and heard in
Spanish
3. Answer
spoken in
Spanish
4. Answer
interpreted
and heard in
English
Q1
A1
Two-Way, Two-Language Question and Answer
This solution can be used for two groups who speak dierent languages and need a back-and-forth dialogue. A single interpreter
alternates between languages, first interpreting English to Spanish, then interpreting Spanish to English, and so on. The Digi-Wave Dock
can be used to easily connect an IC-2 Interpreter’s console for this setup. In this example the audience can ask questions and hear the
answers in their language ( English on Group 1, or Spanish on Group 2).
How it works:
By using the Ch. 2 Out and Relay-In on the IC-2, the Interpreter hears Group 1 (English) while interpreting to Group 2 (Spanish). If a question
is asked in Spanish, the interpreter switches to “Relay-In/Ch 2 Out OFF” mode to hear the question in Spanish and interprets Spanish back
to English. English travels back from the IC-2 in the opposite direction.
Audience members choose the Group for whichever language they want (Group 1 for English, or Group 2 for Spanish). The Audience
stays in their Group (they don’t need to change Groups), and they can ask questions, make statements, and hear questions and answers/
statements in their language. When anyone in either group asks a question, the audience members hear it in their language, and they also
hear the answer in their language.
Required Equipment:
One Digi-Wave dock, One IC-2 Interpreter’s Console, two DLTs, 3 XLR cables, one XLR-RJ45 IC-2 cable, audience DLTs/DLRs as required.
14
Page 15
Order of speaking:
Digi-Wave Dock Application Guide
English
Spanish
delay
Unit
Location
Dock 1
Bay 1 *
Audience Member
speaks 1st Question
in English
Interpreter
interprets1st Question
English -> Spanish
Interpreter switches interpretation mode on IC-2 and begins interpreting the other language.
End of dialog. The person speaking has finished.
There is a slight delay when the Interpreter starts listening to a new line of dialog and begins interpreting to the other language.
delay
Interpreter
interprets 1st Answer
Spanish -> English
Audience Member
speaks 1st Answer
in Spanish
Audience Member
speaks 2nd Question
in English
interprets 2nd Question
delay
Interpreter
English -> Spanish
delay
Interpreter
interprets 2nd Answer
Spanish -> English
Audience Member
speaks 2nd Answer
in Spanish
Two-Way, Two-Language Question and Answer
Unit Programming
Model Mode Priority Group Address
Master 1
1 01
DLT 300
2-way
A585
(English)
Dock 1
Bay 2 *
DLT 300
2-way
Master 1
2 01
(Spanish)
Spanish
Audience
Ch. 1
English
Audience
Ch. 2
DLT 300
presenter
DLR 360
listeners
DLT 300
presenter
DLR 360
listeners
2-way
2-way
Guest
2
02 ... 99 **
- -
Guest
1
02 ... 99 **
- -
* Docked DLT must have it’s bay switch set to “Auto”. This keeps the battery charged and locks the TALK button on. When
the Dock gets powered up the DLT will begin transmitting automatically. When listeners enter the room, their receivers (or
transceivers) will sync to the docked unit and begin receiving audio.
** Each unit within a Group must have a unique address.
15
Page 16
Digi-Wave Dock Application Guide
Audience members
with DLTs
can ask questions
and hear answers
in Group 1 English
DLT Programming:
Mode:
Priority:
Group: 1
Address: 02...99*
Talk Mode: PnL
Talk Button: ON
English
(Group 1)
Digi-Wave
Dock (rear)
Analog
Line Input
(XLR)
DLT Programming:
Mode:
Priority:
Group: 1
Address: 01
Talk Mode: PnL
Talk Button: ON
Docked
DLT
Group 1
English
Bay switches
set to “Auto”
Line Input
DLT Programming:
Mode:
Priority:
Group: 2
Address: 01
Talk Mode: PnL
Talk Button: ON
Analog
(XLR)
Docked
DLT
Group 2
Spanish
Audience members
with DLTs
can ask questions
and hear answers
in Group 2 Spanish
Spanish
(Group 2)
3. Audience member answers
in Spanish
Audience members
with DLRs
listen to
Group 1 English
DLR Programming:
Group: 01
Address: 02...99*
DLT Programming:
Mode:
Priority:
Group: 2
Address: 02...99*
Talk Mode: PnL
Talk Button: ON
Interpreter translating
English to Spanish
or Spanish to English
Audience members
with DLRs
listen to
Group 2 Spanish
DLR Programming:
Group: 02
Address: 02...99*
on Group 2
on Group 1
Analog
Line Input
(XLR)
2. Interpreter speaks question in Spanish
1. Audience member asks English question
4. Interpreter speaks answer in English
16
Page 17
Digi-Wave Dock Application Guide
Five Simultaneous Talkers with a 2.0 System
The 2.0 series Digi-Wave System is limited to two simultaneous talkers within the wireless system. Now the Digi-Wave Dock can be used to
add three additional speakers for a total of five. This scenario is set up as one-way communication from the presenters to the audience.
In this example, a city council meeting has five council members that need to speak at any given time. The audience needs to hear all five
council members. Since all council members are sitting at the same table, they can hear each other speak, and do not require two-way
communication with each other. The system example here allows the audience to hear all five council members.
Note that many other configurations are possible to allow a free-floating transceiver for audience questions/comments - and in that case
this would have to be set up as a two-way communication system, with transceivers in the dock. A wireless microphone system could be
mixed into the dock if a wireless microphone system is available.
How it works:
This example takes advantage of the dock’s ability to mix input signals. By combining inputs at the first dock, the voices of Council
Members 2 & 3 (Group 2) are combined with the voices of Council Members 4 & 5 (Group 3), then combined with the voice of Council
Member 5 (Group 1). The combined audio from all groups is transmitted out to the audience on Group 1.
Required Equipment:
Two Digi-Wave docks, six DLTs (1 docked, 5 for talkers), two DLRs (both docked), one stereo RCA cable, one XLR cable, audience DLTs/
DLRs as required.
Group 1
Group 1
(All ve voices)
1
C
o
u
Group 2
l M
i
c
n
2
embe
rs
3
Group 3
Group 1
4
5
Group 1
Group 1
17
Page 18
Digi-Wave Dock Application Guide
Unit
Location
Dock 1
Bay 1 *
Dock 1
Bay 2 *
Dock 2
Bay 1 *
Council
Member5DLT 100 2.0
Council
Member1DLT 100 2.0
Model Mode Priority Group Address
DLT 100 2.0
DLR 60 2.0 - - 2 -
DLR 60 2.0 - - 3
Five Simultaneous Talkers with a 2.0 System
Unit Programming
2-way
2-way
2-way
Chairman Master
Chairman Slave
Chairman Master
1
01**
-
1
2
02 **
01 **
Council
Member2DLT 100 2.0
Council
Member3DLT 100 2.0
Council
Member4DLT 100 2.0
Audience DLR 60 2.0 - - 1
2-way
2-way
2-way
Chairman Slave
Chairman Master
Chairman Slave
2
3
3
02 **
01 **
02 **
-
* Docked DLT must have it’s bay switch set to “Auto”. This keeps the battery charged and locks the TALK button on. When
the Dock gets powered up the DLT will begin transmitting automatically. When listeners enter the room, their receivers (or
transceivers) will sync to the docked unit and begin receiving audio.
Docked DLRs should also have the bay switch set to “Auto”; this keeps them powered up and they begin receiving when the
dock powers up and the Master is found.
** Each unit in a Group must have a unique address.
18
Page 19
Digi-Wave Dock Application Guide
Taking advantage of the dock’s ability to mix input signals, this configuration alllows 5 people to talk at the same time. By daisy-chaining inputs from one dock to the next, a
speaker’s voice is mixed in, one at a time, to the end of the chain. The return connection from the last bay’s output back to the first bay’s input completes the chain, allowing
everyone to hear, and speak to, each other.
Audience
DLRs
(Group 1)
DLR Programming:
Group: 01
Group 1
Council
Member #5
DLT
Group 1
MAS
CHAIRMAN
GROUP
TALK
DLT Programming:
Mode:
Priority:
Group: 1
Address: 2
Talk Mode: PnL
Talk Button: ON
Group 2
Council
Member #1
DLT
Group 2
MAS
CHAIRMAN
GROUP
TALK
DLT Programming:
Mode:
Priority:
Group: 2
Address: 1
Talk Mode: PnL
Talk Button: ON
Council
Member #2
DLT
Group 2
SLV
CHAIRMAN
GROUP
TALK
DLT Programming:
Mode:
Priority:
Group: 2
Address: 2
Talk Mode: PnL
Talk Button: ON
Council
Member #3
DLT
Group 3
TALK
DLT Programming:
Mode:
Priority:
Group: 3
Address: 1
Talk Mode: PnL
Talk Button: ON
CHAIRMAN
GROUP
Group 3
Council
Member #4
DLT
Group 3
MAS
TALK
DLT Programming:
Mode:
Priority:
Group: 3
Address: 2
Talk Mode: PnL
Talk Button: ON
DLT Programming:
Mode:
Priority:
Group: 1
Address: 1
Talk Mode: PnL
DLT
Transceiver
Group 1
Bay switches
set to “Auto”
Receiver
Group 2
Talk Button: ON
Digi-Wave
Dock (rear)
DLR
DLR Programming:
Group: 02
Dock bay
not used
Bay switch
set to “Auto”
Receiver
Group 3
DLR
DLR Programming:
Group: 03
Digi-Wave
Dock (rear)
CHAIRMAN
GROUP
SLV
Council Members
1 & 2
Standard
RCA cable
Standard
XLR cable
Council Members
3 & 4
19
Page 20
Digi-Wave Dock Application Guide
Extending a 2.0 Series system with 300 Series Product
The 2.0 series systems are not directly compatible with the newer 300 Series systems. However, by using the Digi-Wave Dock, these
systems can now be used together. The dock can also be used to extend the range of a 2.0 system by adding 300 Series product.
How it works:
A DLT 100 2.0 is inserted into one bay, and a DLT 300 is inserted in the second bay. The bays are tied together with standard XLR cables,
routing the outputs of each bay to the inputs of the other bay. By doing this, two-way communication is established. The DLTs are set to
2-way mode. Audio level adjustments will need to be made to balance voices.
Required Equipment:
One Digi-Wave dock, one DLT 100 2.0, one DLT 300, two XLR cables, and talker DLTs per system as required (in this example, three DLT
300’s and two DLT 100 2.0’s).
2.0 Series System
300 Series System
20
Page 21
Unit
DLT 100 2.0
DLT 300
DLT 100 2.0
DLT 300
Audio level
adjust
+6 dB
2.0
Series
System
300 Series
System
Bay switches
set to “Auto”
DLT Programming:
Mode:
Priority:
Group: 1
Address: 2
Talk Mode: PnL
Talk Button: ON
DLT Programming:
Mode:
Priority:
Group: 1
Address: 2
Talk Mode: PnL
Talk Button: ON
DLT Programming:
Mode:
Priority:
Group: 1
Address: 1
Talk Mode: PnL
Talk Button: ON
DLT Programming:
Mode:
Priority:
Group: 1
Address: 1
Talk Mode: PnL
Talk Button: ON
Docked DLT
Docked DLT
Presenter
Presenter
Standard
XLR cables
SLV
GROUP
TALK
CHAIRMAN
MAS
GROUP
TALK
Location
Digi-Wave Dock Application Guide
Extending a 2.0 System with 300 Series Product
Unit Programming
Model Mode Priority Group Address
Dock
Bay 1 *
Presenters
(2.0 Series)
Dock
Bay 2 *
Presenters
(300 Series)
DLT 100 2.0
DLT 100 2.0
DLT 300
DLT 300
2-way
2-way
2-way:
2-way:
Chairman Master
Chairman Slave
Master 1
1 ** 01 **
1 **
1 ** 01 **
Master 2 1 **
02...99 **
02...99 **
* Docked DLT must have it’s bay switch set to “Auto”. This keeps the battery charged and locks the TALK button on. When
the Dock gets powered up the DLT will begin transmitting automatically. When listeners enter the room, their receivers (or
transceivers) will sync to the docked unit and begin receiving audio.
** Since the 2.0 and 300 Series platforms are incompatible, the same Group and Address can be used for the docked units
without interference.
21
Page 22
info@williamsav.com / www.williamsav.com
800-843-3544 / INTL: +1-952-943-2252
© 2019, Williams AV, LLC TCH 009D
Loading...