Page 1
Date: 02-Apr-15 www.williams-sonoma.com Page 1 of 7
Rev:
KEATING BED
Page 2
Date: 02-Apr-15 www.williams-sonoma.com Page 2 of 7
Rev:
Important Safety Instructions:
Please read all instructions carefully before assembling.
For your safety, assembly by two or more adults is strongly recommended.
Keep instructions for future use.
Use only vendor supplied hardware to assemble. Using unauthorized hardware could jeopardize the structural
integrity of the item.
Pre-assembly:
Remove all parts and hardware from the box and lay out on a clear carpeted or scratch-free work surface, as
this will avoid damaging parts during assembly. The shipping box provides an ideal work surface.
Do not dispose of any packaging or contents of the shipping carton until assembly is completed to avoid
accidentally discarding small parts or hardware.
Use the parts and hardware lists below to identify and separate each of the pieces included.
The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions.
The use of power tools to aid in assembly is not recommended. Power tools can damage hardware and split
wood.
Parts Included:
(A)
(B)
(C)
(D)
(E)
(F)
(G)
(H)
(I)
(J)
(K)
Headboard panel
Footboard panel
Side rail
Headboard left post
Headboard right post
Footboard left post
Footboard right post
Short canopy rail
Long canopy rail
Slat
Support leg
1x
1x
2x
1x
1x
1x
1x
2x
2x
5x
5x
Hardware Included:
(L) Fitting
(M) Flat washer
(N) Spring washer
(O) Allen bolt
M8x50
(P) Allen key
12x
16x
16x
16x
1x
A
B
C
C DE
F
G
HHI
IJK
Page 3
Date: 02-Apr-15 www.williams-sonoma.com Page 3 of 7
Rev:
(Q) Wood Screw
4x30 mm
10x
Tools Required (Not Included):
Phillip Head Screwdriver
Assembly Instruction Steps:
1. Carefully lay the headboard panel (A) upside down on a smooth scratch free surface such as carpet or the
foam from inside the shipping box.
2. Attach the headboard left and right post (D&E) to the headboard panel by aligning the pre-drilled holes on
the posts with exposed wooden dowels on the panel.
3. Insert fitting (L), flat washer (M), spring washer (N) and Allen bolt (O) into the cut holes on the headboard
panel and then tighten by Allen key (P) as shown.
4. Repeat above steps to assembly the footboard left and right post (F&G) to the footboard panel (B).
A E D L N O M
P
8x
Page 4
Date: 02-Apr-15 www.williams-sonoma.com Page 4 of 7
Rev:
5. Attach the side rails (C) to the headboard and footboard with posts by inserting the hook into the correspondent
groove on the posts.
6. Attach the short canopy rails (H) on the top of posts (D, E, F&G) by aligning the predrilled holes at two end of
B
GFL
M N O PC
C
4x
4x
Page 5
Date: 02-Apr-15 www.williams-sonoma.com Page 5 of 7
Rev:
canopy rail with exposed wooden dowels on the posts.
7. Attach the long canopy rails (I) on the short canopy rails (H).
8. Insert flat washer (M), spring washer (N) and Allen bolt (O) into the holes on the canopy rails then tighten by
Allen key (P) as shown.
9. Attach the support legs (K) to the slats (J) by insert the hanger bolt on the leg into insert nut on the slat.
H H D E F
G
4x
M
N O P I H
4x
Page 6
Date: 02-Apr-15 www.williams-sonoma.com Page 6 of 7
Rev:
10. Turn clock-wise to tighten as shown.
11. Place the slat with support leg (J&K) on the cut-out of side rail (C) as shown.
12. Slide each wood screw (Q) go through the screw hole on the end of slat into support slat rail on side rail.
Tighten wood screws by Phillip Head Screwdriver as shown.
Adjusting the levelers:
J
K
5x
10x
J C Q
Page 7
Date: 02-Apr-15 www.williams-sonoma.com Page 7 of 7
Rev:
Due to an uneven floor, the furniture may not sit level due causing it to wobble. If the furniture wobbles, determine
which corner does not touch the ground correctly. With two people follow these steps:
1) Carefully elevate the item slightly to provide access to the levelers attached to the bottom.
2) Turn the levelers until adequate contact will be made with the floor. Gently set down the piece and check
stability.
3) Repeat steps until furniture sits firmly on the ground.
13. Assembly is complete.
Care Instructions:
Dust often using a clean, soft, dry and lint-free cloth.
Blot spills immediately and wipe with a clean, damp, cloth.
We do not recommend the use of chemical cleansers, abrasives or furniture polish on our lacquered finish.
For glass tops and shelves, glass cleaner may be used, but avoid spraying it onto the metal or ceramic
frame.
Hardware may loosen over time. Periodically check to make sure all connections are tight.
Re-tighten if necessary.
Thank you for your purchase
Stores | catalog
Loading...