Wilks USA RX510 Quick Start Manual
Electric Pressure Washer
Nettoyeur Haute Pression Électrique
Read this manual carefully before use and keep it for future reference. Failure to do so may result in injury, property damage and may void the
warranty. Products covered by this manual may vary in appearance, assembly, inclusions, specications, description or packaging.
Lisez attentivement ce manuel avant la première utilisation et conservez-le à titre de référence pour la suite. Faute de suivre ces instructions peut
entraîner des blessures, des dommages matériels et peut annuler la garantie. Les produits décrits dans ce manuel peuvent varier en apparence, en
assemblage, en inclusions, en spécications, en description ou en emballage.
RX510
RX510
© Wilks-USA © Wilks-USA
2
Contents
02 - Contents
03 - Quick Start Guide
05 - Safety Symbols and Information
07 - Using your Washer
Angle to the Cleaning Surface
Distance from Cleaning Surface
Avoid Damaging Surfaces
Turbo Nozzle
Detergent
08 - Using your Washer
Detergent
Operation
Looking After your Product
09 - Troubleshooting & Technical Data
10 - Disposal Regulations
11 - CE Certication
Sommaire
12 - Guide de démarrage rapide
14 - Symboles et consignes de sécurité
16 - Utilisation de votre Nettoyeur
Angle de nettoyage
Distance de la surface à nettoyer
Évitez les surfaces dommageables
Turbo Buse
Detergent
17 - Utilisation de votre laveuse
Détergent
Fonctionnement
Prendre soin de votre machine
18 - Dépannage et données techniques
19 - Réglementation en matière d’élimination
20 - Certicat de conformité CE
En / Fr
RX510
3
Quick Start Guide
The following steps describe the quickest method to get your pressure washer up and
running. However, it is essential you fully read this manual to ensure you are familiar with
the general safety features, precautions and functions necessary to operate the product.
Failure to do so may result in injury and damage to your washer or personal items.
Insert the cable tidy hook into the machine
1. Attach the high pressure hose to the
pressure water outlet of the machine.
2. Attach the spray gun to the high pressure
hose. Prior to operating the machine
please ensure that the high pressure hose
has been completely uncoiled and do not
allow it to recoil during operation.
3. Mount the lance onto the spray gun and
add your desired nozzle.
4. Connect the machine to the water supply
hose and power supply.
5. Turn on water supply.
6. Turn on washer after water has entered
the unit.
1. Fit the handle by aligning the screw holes
at the base of the handle to the top of the
washer unit. Tighten the two screws.
2. Fit the wheels by sliding the fitting into
the sockets on the side of the washer until
they lock securely.
3. Slide the hose tidy onto the back of the unit.
ASSEMBLY CONNECTION
1. Pressure cleaner
2. Water supply hose
3. Water connection
4. Water inlet
5. High pressure hose
6. Water outlet
7. Spray gun
8. Power outlet
9. ON/OFF Dial
* No. 2, 3, 8 are not included
En
RX510
© Wilks-USA © Wilks-USA
4
The angle of spray coming out of the variable nozzle
may be adjusted by rotating the variable nozzle. This
will vary the spray pattern from a 0° narrow high
impact to 60° wide spray.
A clogged or partially clogged nozzle can signicantly
reduce water ow and cause the unit to pulsate while
spraying. To clean the nozzle:
1. Turn off and unplug the unit from the electric mains.
2. Turn off the water supply and relieve any pressure
trapped in the hose by squeezing gun trigger 2-3
times.
3. Separate lance from gun.
4. Rotate the nozzle to the narrow high impact stream
setting. This opens up the fan blades.
5. Using the included tip cleaner, or an unfolded paper
clip, insert the wire into the nozzle hole and move
back and forth until any debris is dislodged.
6. Remove additional debris by back-ushing water
through the nozzle. To do this, place end of a
garden hose (with water running) to end of nozzle
for 30-60 seconds.
With a narrow stream you get a high impact force
and this results in maximum deep cleaning in a
concentrated area. However, this narrow high impact
spray must not be used cautiously, as it may damage
some surfaces.
Pre Operation Nozzle Maintenance
Narrow high impact stream
A wide spray pattern will distribute the impact of the
water over a larger area, resulting in excellent cleaning
action with a reduced risk of surface damage. Large
surface areas can be cleaned more quickly using a
wide spray pattern.
Insert tip cleaner into the nozzle hole and
move back and forth until debris is dislodged
Wide angle spray pattern
Adjusting the spray pattern
Do not store the pressure washer outdoors or in a
location where it may freeze. Any water left in the
machine, gun or any other components will expand if
allowed to freeze, causing damage.
Always turn the motor off before turning the water
supply off.
Never disconnect the hose from machine while the
system is pressurized. To de-pressurize, turn the
motor off, then turn the water supply off and squeeze
gun trigger 2-3 times.
After Operation
En
RX510
5
WARNING: When the machine is used, the following precautions should always be considered:
• To reduce the risk of injury, close supervision is necessary when the machine is used near children.
• Follow all safety codes as well as the Occupational Safety and Health Act (OSHA).
• Ensure safety devices are operating properly before using the machine. Do not remove or modify any part of the
gun or main unit of the machine.
• Stay alert at all times when using the machine and always hold the gun rmly when operating the machine.
• Do not operate the machine when fatigued, suffering from reduced physical, sensory or mental capabilities or
whilst under the inuence of alcohol or drugs.
• Keep the operation area clear of all electrical equipment, persons, animals and pets. Do not leave the machine
unattended when setup for use. Always engage the trigger safety latch after use.
• Do not point the pressure gun at anyone whilst the unit is connected to a water supply.
• Do not overreach or stand on an unstable support. Keep good footing and balance at all times.
• Use a cleaning agent supplied or recommend by the manufacturer. Always protect your eyes, skin, and respiratory
system from detergent use.
• If your eyes (or any other sensitive part of your body) comes into contact with detergent, rinse with plenty of clean
water.
• In the event of an accident, switch off the machine, pull the plug from the socket outlet and disconnect the water
supply.
• Always wear safety goggles, ear protection and protective clothing even when performing maintenance.
• Never put hands or ngers over the spray tip while operating the unit.
• Never try to stop or deect leaks with any body part.
WARNING: The electrical supply connection must be made by a qualied person and comply with IEC
60364-1. The electric supply to this machine should include either a residual-current device / circuit
breaker that will interrupt the supply if the current to earth exceeds 30 mA for 30 ms.
Safety and Warning Information
Safety Symbols
CAUTION: Indicates a
potentially hazardous
situation which, if not
avoided, may result
in minor or moderate
injury.
WARNING: Indicates a
potentially hazardous
situation which, if not
avoided, could result in
death or serious injury.
Risk of electrocution
En
RX510
© Wilks-USA © Wilks-USA
6
WARNING: This is a double-insulated machine so two systems of insulation are provided instead of
grounding. No grounding means are provided for a double-insulated machine, nor should grounding
means be added to the machine. Servicing a double-insulated machine requires extreme care and
knowledge of the system. It should be done only by qualied service personnel. Replacement parts
for a double-insulated machine must be identical to the original parts.
WARNING: Do not use an inlet pressure that exceeds the operating pressure of any of the parts (hoses, ttings, etc).
Ensure all equipment and accessories are rated to withstand the maximum working pressure of the unit.
WARNING: Never spray ammable liquids or use the pressure washer in areas containing combustible dust, liquids
or vapours.
WARNING: Do not spray electrical apparatus and wiring.
WARNING: To ensure machine safety, please only use original spare parts (including nozzles) from the manufacturer
or approved by the manufacturer.
WARNING: Make sure the inlet water is maintained between 0.01MPa and 0.4MPa.
WARNING: If the mains cable is damaged it must be replaced by the manufacturer, or its service agent or similarly
qualied person to avoid a hazard or injury.
WARNING: Use only extension cords intended for outdoor use and that have an electrical rating equal to or more
than the rating of the machine. Examine the cord before using and replace it if damaged. Keep the cord away from
heat and sharp edges. It is recommended that you use a cord reel that keeps the socket at least 60mm above the
ground.
CAUTION: Keep the hose away from sharp objects. Bursting hoses may cause injury. Examine the hose regularly
and replace it if damaged. Do not attempt to repair a damaged hose.
• Never disconnect the high pressure outlet hose from the machine while the system is pressurised. To depressurise machine, turn power and water supply off, then press gun trigger 2-3 times.
• Never operate the machine without all of the components properly connected to the machine (handle, gun / lance
assembly, nozzle, etc).
• Never operate the pressure washer with broken or missing parts. Check equipment regularly and repair or replace
worn or damaged parts immediately.
WARNING: To reduce the risk of electrocution, keep all connections dry and off the ground. Do
not touch the plug with wet hands.
WARNING: Do not use the machine if the supply cord or any important parts of the machine are
damaged (e.g. safety devices, high pressure hoses, etc).
En
Loading...