Wilkerson V29 User Manual
Richland, MI 49083 Tel: (269) 629-5000
WARNING
!
To avoid unpredictable system behavior that can cause personal injury
and property damage:
• Disconnect electrical supply (when necessary) before installation,
servicing, or conversion.
• Disconnect air supply and depressurize all air lines connected to
this product before installation, servicing, or conversion.
• Operate within the manufacturer’s specified pressure, temperature,
and other conditions listed in these instructions.
• Medium must be moisture-free if ambient temperature is below
freezing.
• Service according to procedures listed in these instructions.
• Installation, service, and conversion of these products must be
performed by knowledgeable personnel who understand how
pneumatic products are to be applied.
• After installation, servicing, or conversion, air and electrical supplies
(when necessary) should be connected and the product tested for
proper function and leakage. If audible leakage is present, or the
product does not operate properly, do not put into use.
• Warnings and specifications on the product should not be covered
by paint, etc. If masking is not possible, contact your local
representative for replacement labels.
Installation & Service Instructions
83-543-000
Safety Lockout Valve
Models V19 and V29
ISSUED: February, 2005
Supersedes: August, 2002
Doc. #83-543-000, Rev. 2
OUTLET
DETAIL
OF PIVOT
PIN
INSTALLATION
1. Refer to Warnings prior to installation.
2. Install as close to the point of use as possible.
3. Unit must be installed with the flow in the direction of the flow arrow
on top of the body.
4. Avoid using reducing bushings, couplings, etc., whenever possible
to install this product. These devices restrict air flow and can affect
performance.
5. Maximum pressure rating is 150 psig (10.3 bar). Temperature
range is 32°F to 150°F (0°C to 65.5°C)
6. Unit can be locked in the closed position using a standard padlock.
MAINTENANCE
THE UNIT MUST BE REMOVED FROM THE COMPRESSED AIR LINE.
1. Remove retaining screws, and separate body halves.
2. Remove shut off blade.
3. Remove o-rings from body halves.
4. Lightly lubricate o-rings with Magnalube-G or equivalent and place
in grooves on body halves.
5.
Align shut off blade on pivot pin located on outlet body half as shown.
6. Place body halves together and tighten screws to approximately
20 in/lbs.
SELF-TAPPING
SCREWS
INLET
BODY
O-RING
OPEN
PUSH
TO
PIVOT
PIN
OUTLET
BODY
CLOSE
PUSH
TO
SHUT
OFF
BLADE
O-RING
Safety Lockout Valve Models V19 and V29 83-543-000
PUSH
G
TO
CLOSE
H
PUSH
TO
OPEN
F
B
C
E
D
A
J
PUSH
OPEN
TO
K
INCHES
millimetersDimensions
Models A B C D E F G H J K
V19 3.16 3.19 1.93 1.19 2.02 0.97 2.36 1.18 1.03 2.28
80 80 49 49 51 24.5 60 30 26 58
V29 2.23 3.41 2.28 1.98 2.13 1.14 2.58 1.29 1.03 2.28
82 86 58 50 54 28 65 33 26 58
ACCESSORIES
Plastic Slide and O-Rings:
V19 .............................................................................. VRP-97-100
V29 .............................................................................. VRP-97-101
WARNING
!
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE
PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS
CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.
This document and other information from The Company, its subsidiaries
and authorized distributors provide product and/or system options for further
investigation by users having technical expertise. It is impor tant that you
analyze all aspects of your application, including consequences of any failure
and review the information concerning the product or systems in the current
product catalog. Due to the variety of operating conditions and applications
for these products or systems, the user, through its own analysis and testing,
is solely responsible for making the final selection of the products and
systems and assuring that all performance, safety and warning requirements
of the application are met.
The products described herein, including without limitation, product features,
specifications, designs, availability and pricing, are subject to change by The
Company and its subsidiaries at any time without notice.
EXTRA COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FOR INCLUSION
IN EQUIPMENT / MAINTENANCE MANUALS THAT UTILIZE THESE
PRODUCTS. CONTACT YOUR LOCAL REPRESENTATIVE.
Loading...