WiLife WLPIC-6X6, WLPC-810I, WLPI-X6, WLPIC-4X6, WLPIC-1X6 User Manual
...
Setup Guide
Internet
Command Center
Pro Install Notes and Cautions
www.wilife.com
Pro
The world’s first and only fully-integrated, PC-based,
Professional Digital Video Security System designed
for small business and home application.
Use this guide to set up the following Pro products:
KITS
Four-Camera Master System
with Command Center Software
WLPIC-4X6
Six-Camera Master System
with Command Center Software
WLPIC-6X6
Components
Indoor Digital Camera Kit
WLPC-810i
Single-Camera Master System
with Command Center Software
WLPIC-1X6
Indoor Camera with Single-Port
Injector Kit
WLPIC-1X1
Six-Port Power Injector
with Command Center Software
WLPI-X6
Cameras
www
Free Remote Viewing for anywhere,
anytime video access
Pro Power Injector
(with Router shown for clarity)
The WiLife Single-Port
Power Injector links a
single camera to the LAN
Extend the system to
standard WiLife cameras with the
WiLife Pro HomePlug® Bridge
Take the time to carefully place and hide your cables. We have
included a thin silver cable and cable coupler to help you
create an attractive install.
If you move cameras from one system to another, you should
always reset the cameras using a paperclip.
Having problems discovering cameras. Follow these steps:
1. Verify the injector and camera have power.
2. Ensure all cables are connected and tested.
3. Confirm that the camera has received an IP address from
the network. When the camera is searching for an address,
all three status LEDs will flash in unison. Once it has
received an address, the bottom LED will show solid.
4. Use Setup...Advanced...Find My Cameras to search for
cameras.
Find more helpful information at www.wilife.com/support.
Check camera focus to ensure best image results. Use WiLife
120º and 54º lenses to better target specific areas.
Use a WiLife NightVision kit to add support for capturing video
in complete darkness.
Check the WiLife Command Center help file (F1) for more
assistance on configuring PC Firewalls.
Specifications
Operating Temperature
Operating Humidity
Operating Environment
Cabling
32º F to 92º F (0º C to 34º C)
Up to 90%, non-condensing
Indoor - protected from water and dust
CAT5e with RJ-45 connectors per IEEE 802.3
This setup guide will assist you in installing and setting up the
WiLife Pro digital video security system. Simply follow these
instructions and you will be up and running fast.
Before You Get Started
A. Ensure the PC meets these system requirements:
Requirement
CPU Speed*
Memory (MB)**
Video Card (MB)
Display Resolution
Hard Drive (MB)
Operating System
Media Player
* Intel® Pentium 4 CPU speed. Dual-core Intel and AMD processors deliver
similar performance at lower clock speeds.
**Microsoft Vista requires more memory to deliver equal performance.
1 2 3 4 5 6
2.2 GHz
512
32 32 64 128 128 256
150 MB for program and a minimum of 10 GB for video storage
512
Microsoft® Windows® XP or Microsoft Vista
Microsoft® Windows® Media Player version 9 or later
Number of Cameras
512 768 1024 1024
1024 X 768 or higher, 32 bit color
™
Lighting
Camera Resolution
WLPB-100
Step
1
Set up Power Injector & Cameras
The WiLife Pro Power Injector delivers power over the Ethernet
lines to each WiLife Pro Camera.
Connect the WiLife Pro Injector power supply. Consider using a
UPS to protect against brief power outages.
3.2 GHz2.4 GHz 2.6 GHz 2.8 GHz 3.0 GHz
Connect one patch cable (provided with camera) for each camera
from the LAN to the “To Network” injector ports 1 through 6.
Connect WiLife Pro Cameras to injector “To Camera” ports, using
the same ports connected to LAN.
By default, the cameras will search for an IP
address using DHCP. While the cameras are
searching for an IP address, all three status
LEDs will flash. When the camera has obtained
an address, the bottom status LED shows solid.
You can now proceed to step 2.
Using Fixed IP Addresses (Advanced)
Step
2
The WiLife Command Center Software turns a standard
PC into a powerful video security control station.
To install the software, ensure you are logged in as Administrator.
The installation process takes several minutes and includes
powerful tools like Microsoft .NET 2.0, UPnP, and Intel IPP.
You are required to reboot the machine after the install to ensure
the drivers are properly recognized by Windows.
Step
3
The wizard automatically runs as you start the Command
Center for the first time. It walks you through the initial setup
of system options and configuration of your cameras.
Create a new account or use an existing account for WiLife Online access.
Install WiLife Software from CD
Complete First Run Wizard
Network Bandwidth
Frame Rate
Step
4
There are two methods for connecting to the WiLife Online
servers - direct and relay. Direct mode is the best.
In relay mode, video is relayed through WiLife servers, avoiding
router and firewall setup - but, it includes limits on viewing time.
In direct mode, video is routed directly to remote viewing clients,
enabling unlimited viewing time and faster connections.
By default, WiLife will automatically attempt to configure the
local router and firewall to enable Direct connections using
UPnP. In most cases, it is successful.
To verify that WiLife was able to configure your router, open
the Setup...Online tab in the Command Center and look for
the connection mode. If it reads Direct Mode, you are done.
2 lux Standard, 0 lux with WiLife NightVision kit
640 X 480 and 320 X 240 - user selectable
300 kbps to 800 kbps - user selectable
15, 10, and 5 FPS - user selectable
Confirm Online Direct Connect
B. Test Internet connection speeds for remote viewing
and e-mail & cell phone alerts:
Feature
E-mail & Cell Phone Alerts
Remote Viewing
Test upload speeds using one of many online speed test sites. We
recommend www.speedtest.net or www.speakeasy.net.
Upload at 64 Kbps (ISDN, DSL, Cable) with always-on link.
Upload at 128 Kbps (DSL, Cable) with always-on link.
Internet Bandwidth Requirement
C. Use CAT5e or CAT6 cable only. Validate hand-built
cables using a professional cable tester. All cables
pairs (1/2, 3/6, 4/5, 7/8) must be sound.
WARNING: Mis-connected cables may cause damage
to either your cameras or network equipment.
D. Gather the following setup information:
E-mail address (to be used as WiLife Online account
user name) and password.
E-mail (SMTP) server, user name, and password for set up of
e-mail and cell phone alerts.
Use DHCP whenever possible. But, if you must assign static IP
addresses, follow these instructions:
Copy the WiLifeSetIPAddress EXE and PDF to the PC hard drive.
The files are located on the WiLife CD in the bin directory.
Run the WiLifeSetIPAddress program, first ensuring the WiLife Command
Center is not running.
Select the LAN Network Card and click Start to search for your cameras.
Enter the IP addresses and click Set to write the address to the cameras.
You can get additional information by reading the WiLifeSetIPAddress PDF.
Select the WiLife Pro Power Injector networking option.
Follow these steps to manually configure your system for
Direct Connections:
Enable UPnP on your firewall or router, if possible or ...
On your router, map ports 20570 to 20572 (TCP) to the computer's
IP address. You may find the site www.portforward.com helpful.
Restart the WiLife Command Center and recheck the Online Status.
You can find additional information in the WiLife Support
online knowledgebase at www.wilife.com/support.
Most Popular WiLife Features
WiLife
There are two main screens in the WiLife Command Center software,
Live and Playback. Click the GO TO PLAYBACK button to open the
Playback screen. Click the GO TO LIVE button to go back to the
Live View screen.
The SETUP button opens the Setup dialog screens that allow you
to modify settings for your cameras.
The WiLife button opens www.wilife.com.
WiLife
WiLife automatically records video when cameras detect motion.
Upgrade to WiLife Platinum
WiLife
camera kits for the Indoor, Outdoor, or Spy cameras.
WiLife
2. Position the camera on a window, desktop, or wall (using the
mounting options available) and connect to the WiLife Power
Supply.
3. If you set a custom password, click Setup > Advanced and click
Find My Cameras. It will take WiLife 1 to 2 minutes to locate the
camera.
Product Help
WiLife
WiLife
WiLife WiLife
Log into WiLife Online at online.wilife.com and you can access live video
from your cameras anywhere in the world, at any time. WiLife automatically
determines your system’s firewall settings and Internet capability in order
to stream video to you in the most direct way possible. If WiLife cannot find
a direct path, we send the video through our own WiLife servers to you.
Now that’s hassle free service!
Using a Windows Mobile® enabled wireless PDAs or cell phones, log into
WiLife Online at online.wilife.com and you can access live video
from your cameras anywhere in the world, at any time.
WiLife automatically determines your phone’s bandwidth in order to
stream video to you in the most direct way possible. If WiLife cannot find
a direct path, we send the video through our own WiLife servers to you.
Now that’s hassle free service!
Upgrade to WiLife Platinum™ and expand your already powerful WiLife
Video Security System™ with enhanced monitoring, remote play back,
digital pan-tilt-zoom, scheduled alerts, and online video storage.
Adding the advanced capabilities of WiLife Platinum gives you more power
and flexibility to protect your property, family, and employees — providing
you with the ultimate in video security. Learn more at online.wilife.com.
www.wilife.com/support/downloads.
Setup is designed to have your system and cameras running in a few minutes.
However, if you are experiencing difficulties or have questions, please
contact us. Our support team is available 24/7. We have online and phone
support to make your setup easy.
Go to http://www.wilife.com/support for immediate support. You can email
our support team or view help information in our Knowledgebase.
For live support, call our toll-free 24-hour support number: 1.888.GOWILIFE
.
WiLife
during the WiLife installation or
SQS-130-A
10211-A
Loading...