Wild tech WT-KLD, WT-LGP, WT-CUB, WT-FST, WT-GBF User Manual

User Guide

Professional Entertainment Technology

Page 2

1. Introduction

2. Safety Instruction

3. WT-KLD

3.1 Change lamp

3.2 Beam angle

4. WT-LGP

4.1 Change lamp

4.2 Inserting/ Exchanging rotating gobos

4.3 Beam angle

5. WT-CUB

5.1 Change lamp

5.2 Beam angle

6. WT-FST/ WT-GBF

6.1 Change lamp

6.2 Beam angle

7. WT-OIL/ WT-OIL 150/ WT-OIL 250

7.1 Change lamp

7.2 Change oil wheel

7.3 Beam angle

8. WT-HLC/ WT-FAN/ WT-OBT

8.1 Exchanging rotating gobos/ Change lamp

8.2 Beam angle

9. WT-WAV/ WT-IFO

9.1 Change lamp

9.2 Beam angle

10. Troubleshooting

11. CA-16/ CA-416

11.1 Install & Connection

12. Fixture Cleaning

1. Introduction

Thank you for purchasing Wild Tech products. To familiarize yourself with the unit and for your own

safety, please carefully read the instructions which include important information about installation,
operation, and maintenance.

Hereunder is a brief introduction of what is “ Wild Tech ”:

Every single species that survives in the wild is equipped with a particular technique…… As does

Acme’s Wild Tech. Why not show off!

Wild tech is a collection of unique, gorgeous disco lights that comes with flawless engineering to

create impressive, amazing effects. Offering a comprehensive range of effect possibilities, Wild Tech

starts from the introduction of Kaleido, Cubist, Hallucination, …… Inferno to Logo Projector, covering
DJs’ various needs in lighting effects.

By combining the latest technology and innovative ideas, Wild Tech features excellent optics, special

designed gobo and effect wheels, bright and powerful light output, perfect for discotheques, clubs,
pubs, mobile DJs, and home parties. A considerate design of Wild Tech DMX controller CA-16 and a
DMX Switch Pack CA-416 are added for the control of power on/off. Wild Tech is both affordable and
very easy to use.

Remaining cool all night, Wild Tech brings you endless effects with boundless energies. Come

experience Wild Tech and go wild.

Page 3

2. Safety Instruction

WARNING

♦ Please keep this

User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this
instruction booklet.

♦

Unpack and check carefully there is no transportation damage before using the unit.

♦

Before operating, ensure that the voltage and frequency of power supply match the power requirements of the
unit.

♦

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

♦

The unit is for indoor use only. Use only in a dry location.

♦

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces. Be
sure that no ventilation slots are blocked.

♦

Disconnect mains power before fuse/lamp replacement or servicing.

♦

Replace fuse/lamp only with the same type.

♦

Make sure there is no flammable materials close to the unit while operating as it is fire hazard.

♦

Use safety cable when fixes this unit.

♦

Maximum ambient temperature is TA: 40 . Don’t operate it where the temperature is higher than this.

♦

Unit surface temperature may reach up to 85 . Don’t touch the housing bare-hand during its operation. Turn off
the power and allow about 15 minutes for the unit to cool down before replacing bulb or serving.

♦

In the event of serious operating problem, stop using the unit immediately. Never try to repair the unit by
yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the
nearest authorized technical assistance center. Always use the same type spare parts.

♦

Don’t connect the device to any dimmer pack or power pack.

♦

Do not touch any wire during operation as high voltage might be causing electric shock.

Warning

♦

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.

♦

Never touch bulb with bare fingers as it is very hot after using.

♦

Hot lamp explosion hazard. Do not open the unit within five minutes after switching off.

♦

Do not start on the unit without bulb enclosure or housing are damaged.

♦

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

♦

Do not look directly at the light while the bulb is on.

Caution

There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs yourself.
In the unlikely event your unit may require service, please contact your nearest dealer.

Rigging the fixtures

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to
avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the
unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable
that can hold 12 times of the weight of the unit when installing the fixture.
The installation must be carried out by qualified service people only. The device should be installed out of
reach of people and outside areas where persons may walk by or be seated.

3. WT- KLD

Please read carefully the instruction, which includes important information about

the installation, usage and maintenance.

Page 4

Kaleido is a unique 250W kaleidoscopic effect that projects a swarm of swirling patterns. Comes with great built-in
programs with auto movement or sound activation. It's linkable, performing synchronized light show, perfect for
discos, clubs, bars, and parties.

• Precise optics with special gobo / color wheel.

• Linkable by using stereo cable with 3.5mm stereo jack ( optional )

• Focus adjustable and fan cooled.

• Optional easy controller CA-8 for many lighting shows .

Stand by

Blackout the unit

Function

Speed of gobo wheel and
mirrored-tunnel: Fast and
slow

Speed of gobo wheel and
mirrored-tunnel: Fast and
slow

a.) Adjust gobo wheel rotating direction

and speed.

b.) Adjust mirrored-tunnel rotating

direction and speed.

Mode

Sound
(LED off )

Auto
(LED on)

Latch
(LED blinking)

Specification:

• Voltage: AC 120V~60Hz 230V/240V/250V~50Hz/60Hz

• Fuse: 20mm glass 250V T6.3A / 20mm glass 250V T5A

• Bulb: ELC 24V 250W

• Dimension: 306 x 263 x 140 mm

• Weight: 8 kgs

3.1 Change lamp

• Always switch off the mains supply and never handle the lamp or luminaire when it

is hot.

• Do not touch the bulb with bare hands. If this does happen, clean the lamp with

denatured alcohol and wipe with a lint free cloth before installing.

Pull the socket off the lamp. Do not pull the wires.

3.2 Beam angle

The Projector is best to be placed 5 meters from wall, and from this distance the light effect will cover an area of

3.7 m x 3.7 m.

4. WT-LGP

Logo Projector is a powerful tool creating a long lasting visual effect. It comes with 7 D size gobos and an
interchangeable slot for custom made gobos. With speed and direction adjustable function, the Logo projector is
perfect for discos, restaurants, department stores, etc.

• Adjustable gobo rotation direction and speed.

• With an optional CA-5 easy controller for the on/off control.

• Focus adjustable and fan cooled.