TWIN / TWIN BUNKBED
ASSEMBLY INSTRUCTIONS
PAGE 1 OF 8
ASSEMBLY INSTRUCTIONS
ROLL SLAT
ASSEMBLY TIPS:
1. Remove hardware from box and sort by size
2. Please check to see that all hardware and parts are present prior to start of assembly.
3. Please follow attached instruction in the same sequence as numbered to assure fast & easy assembly.
Warning!
!
1. Don't attempt to repair or modify parts that are broken or defective. Please contact the store
immediately.
2. This product is for home use only and not intended for commercial establishments.
PARTS IDENTIFICATION
A1
A2
B
C
D
E
F
LEFT UPPER BED
END
RIGHT UPPER
BED END
LOWER BED END 2PCS
UPPER & LOWER BED
RAIL
UPPER FRONT
BED RAIL
LOWER FRONT
BED RAIL
LONG
GUARDRAIL
1PC
1PC
2PCS
1PC
1PC
1PC
HARDWARE IDENTIFICATION
1
2
3
4
5
6
7
8
LONG BOLT 24PCS
NUT 24PCS
METAL ROD 4PCS
ALLEN WRENCH 1PC
FLAT HEAD SCREW 12PCS
WOOD DOWEL 16PCS
SHORT BOLT 8PCS
ALLEN CAP SCREW 8PCS
G
H
I1
I2
J
K
SHORT
GUARDRAIL
TRESTLE BAR
LEFT LADDER STILE
RIGHT LADDER STILE
LADDER STEP 4PCS
(14 PCS)
1PC
1PC
1PC
1PC
2SETS
PAGE 2 OF 8
ASSEMBLY INSTRUCTIONS
STEP 1
1.1) Insert wood dowel to lower bed end.
1.2) Align and fasten lower bed rail and lower front bed rail to lower bed end using nut and long bolt. Tighten
with Allen wrench.
STEP 2
Align and fasten roll slat to bed rails using flat head screw and tighten with screw driver (not included).
PAGE 3 OF 8
ASSEMBLY INSTRUCTIONS
STEP 3
3.1) Insert wood dowel to left and right upper bed end.
3.2) Align and fasten upper bed rail and upper front bed rail to left and right upper bed end using nut and long bolt.
DO NOT TIGHTEN AT THIS STEP.
3.3) Align and fasten long guardrail to left and right upper bed end using nut and long bolt. THEN TIGHTEN ALL
THE BOLTS AT STEP 3.2 & 3.3 WITH ALLEN WRENCH.
STEP 4
4.1) Insert wood dowel to the end of short guardrail.
4.2) Align and fasten short guardrail to trestle bar and right upper bed end using nut and long bolt. DO NOT
TIGHTEN AT THIS STEP.
4.3) Align and fasten trestle bar to upper front bed rail using short bolt. THEN TIGHTEN ALL THE BOLTS AT
STEP 4.2 & 4.3 WITH ALLEN WRENCH.
4.4) Align and fasten roll slat to bed rails using flat head screw and tighten with screw driver (not included).
PAGE 4 OF 8
ASSEMBLY INSTRUCTIONS
STEP 5
Align and fasten ladder step to left and right ladder stile using Allen cap screw and tighten with Allen wrench.
PAGE 5 OF 8
ASSEMBLY INSTRUCTIONS
STEP 6
Insert metal rod to the top of lower bed end. Align and place the upper bed end onto the lower bed end.
STEP 7
Align and fasten ladder stile to the lower and upper front bed rail using short bolt and tighten with Allen wrench.
PAGE 6 OF 8
SAFETY WARNING
Follow the information on the warning attached to the upper bunk end structure and on the carton. Do
1
not remove this label.
Always use the recommended size mattress or mattress support or both to help prevent the likelihood of
2
entrapment or falls.
3 Surface of mattress must be at least five inches (127mm) below the upper edge of guardrails.
4 Do not allow children less than six years of age to use the upper bunk.
5 Prohibit more than one person on upper bunk.
Periodically check and ensure that the guardrail, ladder and other components are in their proper
6
position, free from damage, and that all connectors are tight.
7 Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8 Always use the ladder for entering and leaving the upper bunk.
9 Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
10 Use of a night light may provide added safety precaution for a child using upper bunk.
If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed should be
11
placed against the wall to prevent entrapment between the bed and the wall. (This applies only to bunk
beds without two full-length guardrails.)
12 Always use guardrails or both long sides of the upper bunk.
13
The use of water or sleep flotation mattress is prohibited.
14 Keep these instructions for future reference.
STRANGULATION HAZARD:
Never attach or hang items to any part of the bunk bed that are not designed for use with the bed for
15
example, but not limited to hooks, belts, and jump ropes.
SIZE OF MATTRESS AND FOUNDATION:
Use only mattress which is 37 ½” – 38 ½” in width and 74” – 75” in length. The total thickness of
mattress and foundation (slat kit, bunk board, etc.) combined must not exceed 6”
Note: There must be at least 5” from mattress sleeping surface to top edge of guardrail.
PAGE 7 OF 8
1. When using beds as bunk beds, the ladder MUST be securely
attached to the upper bunk rail at all times.
2. When using the beds as two (2) separate floor-standing beds,
the ladder MUST be stored in a separate location where children
cannot use the ladder in any manner.
3. DO NOT use, nor permit children to use, the ladder in any
manner whatsoever, other than to access the top unit when
used as bunk beds, and only if the ladder is securely attached
to the top bunk rail, as set forth in the instructions.
4. Any misuse or unauthorized use of the ladder could result in
serious or fatal injury.
PAGE 8 OF 8
Loading...