Wilding Wallbeds Sierra 35 Instruction Booklet
Side Mount
Revision 7/13 BK35
INSTRUCTION BOOKLET #35
WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE
TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS
COULD RESULT IN SEVERE PERSONAL INJURY TO USER OR DAMAGE TO PRODUCT.
PLEASE CONTACT CUSTOMER SERVICE AT 866-725-6401 FOR ANY QUESTIONS.
Model:
Sierra
With Storage Head Board
Tools Needed
Ratchet
Step Ladder
1/2” Socket
Phillips screwdriver
Large regular screwdriver
Small regular screwdriver
3/8” Socket
7/16” Socket
Crescent wrench
1/2” open end wrench
1/4” wood drill bit
1/4” Allen wrench
studsensor
Stud finder
Cordless screw driver
with Phillips bit
STAN LEY
Tape measure
Hardware Page
Bag 7
Item
5/16’’ Plain
Hexagon Nut
5/16’’ Nylock
Hexagon Nut
3/4’’ Cam
Washer
Qty
10
6
2
2
Item
3/16’’ Nylock
Hexagon Nut
3/16” Washer
3/16’’x 1 Black
Flathead Screw
1/4” Star Washer
1/4’’
Bag 8
Qty
16
2
2
2
Item
1/4’’x 3/4’’
Hex Head Bolt
3/4’’ Flat head
Screw
4 hole corner
bracket
Qty
Other Hardware
Item
2
Cam Fitting
6
Connecting Bolts
1/4’’
1 Square Drive Wood
Screw
4
1/4’’
1 Wood Screw
1/2’’
3 Wood Screw
Qty
4
37
160
4
3
7/8” Washer
5/16’’ x 1 1/4’’
Flat Head Bolt
5/16’’ Allen
Head Bolt
5/16’’ x 3/4’’
Hex Head Bolt
4 mm x 1/4’’
Flat Head Screw
10
2
4
4
5/8’’ Pan
head Screw
3/16’’ x 1/2’’
Black Truss
head screw
Leg Stop
2’’ Flathead
Wood Screw
135
14
2
“L” Bracket
Spacer Plate
6
1 left
(
1 right
3
Square Tip Bit
1
Bed Handles
2
)
Bed Models:
Sierra
2
4
1”
Step 1: Locate the left and right
Side Boards and then from the
square white box locate the two Lift
Mechanisms, hardware bags and
springs.
Cut out for room
base molding
Finished edge
X 2
Lift Mechanism
Left Side Board Right Side Board
Step 2:
The number of springs in the Lift Mechanism required varies with the different weights of
mattresses. If you purchased your mattress with your bed from Wilding Wallbeds refer to the
chart to the right. This will also be a good reference point for mattresses not purchased with
your Wall Bed.
NOTE: After you have completed installing and checking operation of your Wall bed, you
may find it necessary to add or remove springs to achieve the correct lift effort of between
5 and 10 pounds.
Install the first spring in hole #5 (center position) on both the Mounting Plate and the Tension Arm. Hook one end of the
spring under the upturned edge of the Mounting Plate. Lay the spring down and slide it under the matching hole in the
Tension Arm. See illustration 1.
HELPFUL HINT: You may find it easier to fit the hook
under the Tension Arm if you pry up the Arm Bracket with
a wooden wedge or similar device.
Install Springs in the Lift Mechanisms
Bed Size
Queen
Full/Double
Twin/Single
Number of Springs
Illustration 1
Continue by working out from the
center, alternating top and bottom,
until you have installed the required
number of springs.
Hole #1
Upturned edge of
(Right lift mechanism)
mounting plate
5
3
1
IMPORTANT! Be sure that holes
of the Mounting Plate correspond
to the holes in the Tension Arm
and use the same number of
springs and the same configura
tion on both Lift Mechanisms
Repeat Step 2 for Left Lift Mechanism.
-
Hole #5
(Center)
Hole #9
Hole #5
(Center)
Arm Bracket
Tension Arm
Page 1
Hardware needed for next 2 steps from Bag #7
x 8
5/16” Plain Hex Nut
5/16” x 1 1/4” Flathead
Slot Machine Screw
Step 3: Install the Lift Mechanism by inserting a 5/16”
x 1 1/4” Flathead Machine Screw through holes “C”
and “D” from the outside (countersunk holes) of the
Right Side Board. Position the corresponding Right Lift
Mechanism holes. Loosely thread on a 5/16” Plain Hex
Nut on each. Insert the same type screw through holes
“A” and “B”. At hole “A” use one of the Hexagon
Cam Washers in the slot of the mounting plate so that
the LARGER PART OF THE CAM IS UP. At hole
“B” use a 5/16” x 7/8” washer. Thread a nut on each.
Tighten the four nuts evenly, making sure the hexagon
cam washer does not rotate while tightening.
See illustration 2.
IMPORTANT! Over tightening the nuts will pull
the head of the screw too deeply into the Side Board.
Tighten only until the head of the screw is flush with
the Side Board.
Repeat step 3 with the Left Side Board and Lifting
Mechanism.
x 8
Hole A
Hole B
Hexagon Cam Washer
Hole C
Hole D
Finished Edge
x 2
Right
Side Board
x 2
7/8” Washer
Illustration 2
All holes are countersunk
in this side of sideboard
Base Board
Notch
Step 4:
Lay the right and left
Side Boards down as illustrated
and screw Connecting Bolts
into the holes provided and
place Cam Fittings into sockets
provided as shown.
Hardware needed for next step
x 7
Cam Fitting
Left Side
Board
x 22
Connecting Bolt
Right Side
Board
Un-finished
Edges
Page 2
Loading...