Wildfire EM-23S, EM-43S Operation Manual

Operation Manual

Ultraviolet Fluorescent Lighting Fixtures

EM-23S
EM-43S

Table of Contents

Specifications 3

Introduction 4

Unpacking 4
Optional Accessories 4
Setup 4

Maintenance & Troubleshooting 5

Lamp Replacement 5
Cleaning 5
Troubleshooting 5

Diagrams 6

Isometric & Line Views 6
Exploded View & Part List, EM-42S 7
Exploded View & Part List, EM-22S 8
Schematic 9
Spectral Output Graph 10
Photometrics Chart 10

Limited Warranty 11

2

Specifications

This unit is to be operated in accordance with the way it was designed and tested.

OPERATE IN DRY INDOOR LOCATIONS ONLY.

USE WITH MAX 60W T8, T10, T12 LAMPS ONLY.

SUITABLE FOR SURFACE MOUNTING ONLY.

Ballast:

Electronic VHO Power Factor > 70%

Rating:

EM-23S: 100, 120 or 240VAC / 50-60Hz / 3.0A max. / 130W
EM-43S: 100, 120 or 240VAC / 50-60Hz / 4.5A max. / 220W

Circuit Protection:

One 7A Slow Blow Fuse

Lamps:

EM-23S: F20T(12)(10)(8) Non Energy Saver Type Lamps
EM-43S: F40T(12)(10)(8) Non Energy saver Type Lamps

Lamp Life:

8,000 Hrs.

Beam:

40’ Throw, 165° Spread

Reflector:

Polished Everbright Aluminum

Peak Spectra Output:

368nm With Wildfire SableLux Lamps Installed.

Optimum Operating Temperature:

50° F to 100° F

Weight:

EM-23S: 9.95 lbs./4.51 kg.
EM-43S: 15.75 lbs./7.14 kg.

Dimensions:

EM-23S: 4.18”/10.62cm High x 4.90”/12.44cm Wide x 24”/60.96cm Long
EM-43S: 4.18”/10.62cm High x 4.90”/12.44cm Wide x 48”/1.21m Long

Standard Equipment:

Adjustable Mounting Brackets

Optional Accessories:

UVT Protective Lens Kit (2’ 138-010)(4’ 138-011)
Louver Kit (2’ 138-013)(4’ 138-014)
Light Stand Mount (2’ 147-004)(4’ 147-005)
Floor Mount (147-006)
T-Bar Ceiling Mount (147-003)
Quick Trigger Clamp (147-020)

Specifications subject to change without notice

Made in the USA

3

Introduction

Congratulations on your purchase of an Effects Master Standard Series Fixture by Wildfire. These powerful and
versatile ultraviolet fluorescent lighting fixtures feature triple

electronic VHO ballasts. Each Effects Master Fixture is precision engineered to provide you with years of

art
trouble free service. Please take a moment to read this manual thoroughly before attempting to operate this
fixture. I mproper set-up, use or servicing may cause damage to the fixture and/or lamps and v oid the unit’s
warranty.

Unpacking

Unpack the fixture and carefully inspect it for any signs of physical damage. Report any damage to Wildfire or
your local distributor immediately. Included with each unit should be the following items:

1. Two “L” shaped mounting brackets with one 1/2” mounting hole for mounting the fixture to a standard c-clamp
and two 3/8” mounting holes for mounting the fixture to Unistrut or a flat surface.

2. Two rubber friction washers that are to be placed between the mounting brackets and the end caps on either
end of the fixture allowing it to be held firmly in place upon tightening the locking knobs

3. Two locking knobs with ¼-20 threaded studs that screw into the end caps.

Optional Accessories:

UVT Protective Lens Kit - This kit consists of an acrylic plastic lens that slides into the housing to protect the

lamps. Included in this kit are two small brackets that mount on either end of the fixture holding the lens in
place. This protective lens is made from a special UV transmitting plastic and is designed not to yellow or
become brittle under normal operating conditions. Contact Wildfire or your local distributor for pricing

Louver Kit- This aluminum louver features 1” long blades spaced 2” apart that run perpendicular with the

lamps. Included in the louver are two small brackets that mount on either end of the fixture holding it in place.
Contact Wildfire or your local distributor for pricing.

Light Stand Mount - This aluminum mount enables you to attach your Effects Master fixture to any standard

light stand. (Optional 5/8” baby pin or TVMP adapter required) Contact Wildfire or your local distributor for
pricing.

Floor Mount Kit- This aluminum stand set enables you to mount your Effects Master fixture on the floor for

footlight applications. Contact Wildfire or your local distributor for pricing.

T-Bar Ceiling Mount- These brackets enable you to mount your Effects Master fixture to the t-bars in a

standard drop ceiling. Contact Wildfire or your local distributor for pricing.

Setup

The first step is to install the mounting brackets on either end of the fixture (see fig. 2 in the Diagrams section of
this manual). Next install the lamps refer to Lamp Replacement on page 7 for correct installation.

Plug the fixture into the appropriate power source. If you are controlling the unit with a lighting control board you

will need to make sure it is plugged into a non-dim circuit. Do not at any time plug the fixture into a

dimmable circuit, doing so will damage the ballast in the fixture and void the warranty.

lamps, polished everbrite reflectors and state of the

4

Maintenance & Troubleshooti ng

Lamp Replacement

Refer to Fixtures Specifications on page 4 for information on selecting the proper replacement lamp for your
fixture. Unplug the fixture. If this is not possible then steps should be taken that would allow the fixture to remain
in an off state while re-lamping. If your Effects Master is equipped with The UVT protective lens or Transverse
Louver option, this will need to be removed first before replacing the lamps. To remove the protective lens, first
determine which end is easiest to slide the lens from the unit. Looking at that end, locate the two Phillips screws
that hold the lens-retaining bracket to the side of the fixture. Using a Phillips screwdriver, loosen the two screws
that hold the bracket in place. (Do Not Remove the Screws). Once the two screws are loose, the bracket will
slide out from under the screw heads. Now that the bracket is removed, slide the protective lens out of the
housing. Holding the lamp firmly with two hands, one hand near each end of the lamp, rotate the lamp about its
long center-line axis, one quarter (1/4) turn either clockwise or counter-clockwise. The sockets will click and the
lamp will become loose. Gently lift the lamp free of the sockets. Install the new lamp by lining up the two pins
on the ends of the lamp so that they will slide into the open slot in the lamp holder. Gently set the lamp into the
sockets until the lamp pins rest on the lamp socket. Gently turn the lamp one-quarter (1/4) turn either clockwise
or counter-clockwise, until the lamp socket makes a small click or you feel a detent position. Gently lift up on
the lamp to make sure that both ends of the lamp are installed correctly, neither end of the lamp should move in
the socket.

Cleaning

For best performance, the reflector, lamps and protective lens should be kept free of dirt and dust. At no time
should any cleaning chemicals or abrasives be used to clean any part of the unit. For normal cleaning, a dry soft
cloth should be used to wipe any surface free from dust and light dirt. Cleaning the reflector will require that the
lamps be removed. Remove lamps by following the instructions listed under Lamp Replacement above. Always
unplug the unit before cleaning. Once the lamps have been removed, gently wipe off the reflector using a soft
dry cloth. In the event the reflector is heavily soiled, lightly dampen the cloth with a mild window cleaning agent
and wipe. Lamps should be cleaned using the same method; first use a dry soft cloth and then proceed with a
window-cleaning agent if lamp is too heavily soiled. Do not spray or apply any liquid directly to any part of the
fixture.

Troubleshooting

Other than the lamps, there are no user serviceable parts in the fixture.

5

Isometric & Line Views

Diagrams

4.32"

5.00"

24.12"

27.37"

5.00"

4.32"

48.12"

51.37"

6

Exploded View & Part List EM-43S

7

4

201219

56

9

2

8

1

7

7

3

11

3

13

15

18

17

16

14

#

QTY.

PART # PART NAME

1 1

104-065-03

Housing, 4'

2 2

104-059-03

Cover, Housing, Side

3 12

121-005

Screw, M, PHL, PH, 6-32 x 3/8" 18-8 SS

4 1

126-003-03

Reflector, 4' Fluorescent

5 2

104-003-02

Bracket, Mounting

6 2

121-051

Washer, Rubber, Mount Brkt.

7 2

120-002

Knob, Bracket Adjustment

8 1

107-003

Cord, Power, 16 AWG, 8'

9 1

122-001

Strain Relief, Bushing

10 6

108-004

Socket, Lamp G13 Base

#

QTY.

PART # PART NAME

11 12

121-017

SS, PHL, PH, #8, 3/8", 18-8 SS

12 3

141-002

Lamp,SableLux Flouresent, 4' (Optional Lamps)

13 3

121-036

Nut, Nylock, 6-32, 18-8 SS

14 1

110-007to010

Ballast, (120V)(220V)(100V)(277V)

15 1

104-045-02

Control Plate, Blank

16 4

121-001

MS, PHL, PH, 4-40, 1/4", 18-8 SS

17 4

121-056 Washer, Flat

18 4

121-066

Spacer, Nylon, 3/8 od, #8 id, .125" thk.

19 2

104-004-01

Bracket, Lens Retaining (Optional Lens Kit)

20 1

124-016-01

Lens, Clear UVT, 4' x 4 3/4" (Optional Lens Kit)

11

10

Exploded View & Part List EM-23S

8

4

201219

56

9

2

8

1

7

7

3

11

3

13

15

18

17

16

14

#

QTY.

PART # PART NAME

1 1

104-064-02

Housing, 2'

2 2

104-059-03

Cover, Housing, Side

3 12

121-005

Screw, M, PHL, PH, 6-32 x 1/4" 18-8 SS

4 1

126-004-03

Reflector, 2' Fluorescent

5 2

104-003-02

Bracket, Mounting

6 2

121-051

Washer, Rubber, Mount Brkt.

7 2

120-002

Knob, Bracket Adjustment

8 1

107-003

Cord, Power, 16 AWG, 8'

9 1

122-001

Strain Relief, Bushing

10 6

108-004

Socket, Lamp G13 Base

#

QTY.

PART # PART NAME

11 12

121-017

SS, PHL, PH, #8, 3/8", 18-8 SS

12 3

141-001

Lamp, Fluoresent, 2' (Optional Lamps)

13 3

121-036

Nut, Nylock, 6-32, 18-8 SS

14 1

110-007to010

Ballast, (120V)(220V)(100V)(277V)

15 1

104-045-02

Control Plate, Blank

16 4

121-001

MS, PHL, PH, 4-40, 1/4", 18-8 SS

17 4

121-056 Washer, Flat

18 4

121-066

Spacer, Nylon, 3/8 od, #8 id, .125" thk.

19 2

104-004-01

Bracket, Lens Retaining (Optional Lens Kit)

20 1

124-015-01

Lens, Clear UVT, 2' x 4 3/4" (Optional Lens Kit)

11

10

Schematic, EM-23S & EM-43S

9

100-220V

COM

GRND

BLACK

WHITE

GREEN

ELECTRONIC BALLAST

7 AMP FUSE

BROWN

BROWN

RED

RED

YELLOW

YELLOW

ORANGE

ORANGE

BLUE

BLUE

Spectral Output Graph

10

UV-B UV-A

VISIBLE LIGHT

WAVELENGTH /NM

100

300 350 400 450 500

90

80

70

60

50

40

30

20

10

0

RELATIVE ENERGY (%)

With Wildfire SableLux BLB Lamps

Photometrics Chart

Model EM-23S With Narva Lamps

Distance in Feet/Meters

5

/

1.52

10

/

3.05

20

/

6.10

30

/

9.14

40

/

12.19

76.0

23.2

64.0

151.9

46.3

16.0

303.8

92.6

4.0

455.7

138.8

1.7

607.7

185.2

.64

Beam Angle Feet

Beam Angle Meters

Peak UV-A Intensity µW/cm

2

Model EM-43S With SableLux Lamps

Distance in Feet/Meters

5

/

1.52

10

/

3.05

20

/

6.10

30

/

9.14

40

/

12.19

76.0

23.2

161.7

151.9

46.3

40.4

303.8

92.6

10.1

455.7

138.8

4.4

607.7

185.2

2.5

Beam Angle Feet

Beam Angle Meters

Peak UV-A Intensity µW/cm

2

Limited Warranty

Wildfire, Inc. warrants to the original owner or retail customer, that for a period of three years
from the date of delivery of any Wildfire Fixture; whether used in a portable or permanent
installation, such fixtures will be free from defects in material and workmanship under normal
use and conditions.

Warranty does not cover any product or part of a product that has been subjected to accident,
negligence, alteration, abuse or misuse and excludes any accessories or parts not supplied by
Wildfire. Warranty does not cover expendable parts such as fuses, lamps, glass or any
components warranted directly to the owner by the original manufacturer. This warranty does
not extend to products not manufactured by Wildfire.

Wildfire’s responsibility under this warranty shall be to repair or replace at Wildfire’s discretion
such parts as determined to be defective upon Wildfire’s inspection. Wildfire will not assume
any responsibility for any labor expended or materials used to repair any equipment without
Wildfire’s prior written authorization.

Wildfire, Inc. shall not be responsible for any incidental, general or consequential damages to
property, damage for loss of use, time profits or income, or any other charges.

The owners’ obligation during the warranty period is to notify Wildfire of any suspected defect,
to obtain a return authorization number, and to return the product freight and insurance
prepaid to the following address:

Wildfire Service, 2908 Oregon Court Suite G1, Torrance, CA 90503

[phone] [phone]

Collect shipments for freight allowances or shipments without return authorization numbers
will not be accepted.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY AND ALL OTHER WARRANTIES
EXPRESSED OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE AND ALL OTHER OBLIGATIONS AND
LIABILITIES ON WILDFIRE’S PART. THERE ARE NO WARRANTIES WHICH EXTEND
BEYOND THE DESCRIPTION ON THE FACE HEREOF. THE OWNER ACKNOWLEDGES
THAT NO OTHER REPRESENTATIONS WERE MADE TO HIM WITH RESPECT TO THE
QUALITY AND FUNCTION OF THE GOODS SOLD.

This written warranty is intended as a complete and exclusive statement of the terms thereof.
Prior dealings or trade usage shall not be relevant to modify, explain or vary this warranty.
Acceptance of, or acquiescing in, a course of performance under this warranty shall not
modify the meaning of their agreement even though either party has knowledge of the
performance and a chance to object.

This limited warranty gives you specific legal rights and you may also have other rights which
vary from state to state. If any action or preceding results from this warranty, the prevailing
party will be entitled to all costs and attorney fees incurred in defending or prosecuting such
actions.