INSTRUCTIONS FOR THE
OPERATION AND MAINTENANCE
OF THE INDUSTRIAL SUCTION CLEANER
'-
MODEL SN 2000-U
When ordering spare parts, please indicate a Iways the number
of the apparatus and its date of construction.
Important for claims to the guarantee conditions:
For the clarification of guarantee claims it is absolutely necessary
to send us the apparatus respectively the blower unit in uncleaned
condition for inspection.
Wieland KG - 8521 Erlangen-Tennenlohe - Postfach 3669 - Tel. 09131/60075 - Telex 629832
INSTRUCTIONS FOR THE OPERATION AND MA.INTENANCE OF
INDUSTRIAL CLEANER MODEL SN 2000-U
l
-
...•.~
~ .
•••••••
, ,
•••••••
•••••••
••!.~
..wie.und kg.
0902 73
INSTRUCTIONS FOR THE OPERATION AND tv\AINTENANCE OF
INDUSTRIAL CLEANER MODEL SN 2000-U
The industrial cleaner model SN 2000- U is a suction apparatus provided with a powerful,
three-stage blower which is characterised by a high filter performance and simplicity of
operation. The three-stage blower is driven bya 2.2 kW, three-phase current motor, de-
signed for long-term operation. A particular characteristic of the un it is the accomodation
of the power unit and the filter system within a minimum of space, and the optional use of
exchangeable collecting containers or of throw-away paper collecting begs (dust-free empty-
ing) •
Fields of application
The industrial cleaner model SN 2oo0-U :s, in consequence of its filter system, predomi-
nantly suitable for the pick-up of fine dusts, solid bulk material, granulates and turnings,
chips, etc. Using the container provided with the unit, up to a maximum of 30 litres of
liquids can also be picked up.
Before taking into operation, check:
1. that the voltage of the main supply agrees with that shown on the apparatus as operating
voltage. The appropriate voltage is found on the name plate.
2. If the unit is not provided with a phase-sequence relay (direction of rotation switch), the
direction of rotation must be checked at the in itia I switching on and whenever connection
is made with a new power supply outlet •
The correct direction of rotation can be determined through the open ing in the side
panelling, and must correspond with the direction indicated by the arrow. If the di-
rection of rotation does not correspond with the direction indicated by the arrow, the
plug of the apparatus or the power supply outlet should be re-wired accordingly.
Incorrect direction of rotation leads to a considerable loss of power and can cause the
motor to burn out, and also damage the blower.
For this reason, we would recommend ensuring that all the power supply outlets in the
factory are uniformly wired.
wwieland kg.
090273
page 1
INSTRUCTIONS FOR THE OPERATION AND NAINTENANCE OF
INDUSTRIAL CLEANER MODEL SN 2000-U
Filter s.l.stem
The filter system comprises:
a maintenance-free mechanical pre-separator (Part No. 150-120), which virtually comple-
tely separates the suctioned particles from the airstream, and directs them immediately into
the collecting container (Part No. 200- 048), or paper collecting OOg(Part No. 250-061),
a paper collecting OOg(Part No. 250-061) for the storage of the picked up dust particles
and which, at the same time, does service as an additional filter,
an exchangeable cloth filter (Part No. 250-030).
Equipment
A standard item of the apparatus is an interchangeable collecting container having a capa-
city of 60 litres, an interchangeable cloth filter, a throw-away paper collecting OOg, a
perforated PVC OOg, an insertion ring for the paper collecting OOgand a rubber cap.
Function and operation
Depending upon the material to be removed, either the metal interchangeable collecting
conta iner or the paper collecting OOg(strengthened with aperforated PVC OOg), can be
used as a recipient for the suctioned material.
In order to remove the interchangeable collecting container, the paper collecting OOgor the
cloth filter, the locking device (Part No. 150-017) is opened, and the mechanical pre-separa-
tor tilted OOckwards.
Perfora ted
PVC bag
Fig. 5
For the pick-up of fine dust and
for dust-free emptying, paper col-
lecting OOgsare used. The PVC OOg
serves to provide the paper OOg
with more mechanical strength.
wwie.und kg.
Paper collecting bag
for fine dust
0902 73
page 2
INSTRUCTIONS FOR THE OPERATION AND MAINTENANCE OF
INDUSTRIAL CLEANER MODEL SN 2000-U
1. Suctioning into the exchangeable collecting container
The interchangeable collecting container is used for the removal of turnings, chips,
liquids and granulates.
The picked up particles are led directly into the interchangeable collecting container,
with the exception of apart of the floating particles. These floating particles are caught
by the exchangeable cloth filter. When the material to be removed by suction contains
fine dusts, it is recommended tOOtthe paper bog be inserted into the cloth filter. In this
way, a cleaning of the cloth filter is not necessary and a complete filtering out of the
fine dust is achieved.
Insertion of the paper collecting bog:
1. 1 Interchangeable collecting conta iner (Part No. 200-048) is removed.
1.2 The paper collecting bog (Part No. 250-(61) is inserted into the cloth filter in
such a way that it comes into contact with the cloth filter (Part No. 250-030) over
its entire surface area. The folds that result during the process are smoothed out by
hand.
1.3 The paper collecting bog (Part No. 250-(61) is folded over the edge of the mein fil-
ter housing, the interchangeable collecting container (Part No. 250-048) is inserted
and the mechanical pre-separator (Part No. 150-120) is closed.
When suctioning is carried out with inserted paper collecting bog and collecting container,
the paper collecting bog is replaced bya new and clean one as soon as the suction power
begins to fa II off.
If suctioning is carried out without an inserted paper collecting bag, the suspended cloth
filter must be cleaned when the suction power falls off.
wwieland kg.
090273
page 3
INSTRUCTIONS FOR THE OPERATION AND NAINTENANCE OF
INDUSTRIAL CLEANER MODEL SN 2000-U
Suctioning of turnings, chips ond liquids
Immersion tube open
Interchangeoble collecting container
Paper collecting bog,
necessary on Iy for fine dust
l
Immersion tube open
For the removal of chips and turnings, liquids
and coarse dust, the apparatus is operated
with the immersion tube open - that is, with-
out a fitted rubber cap - and with inserted
interchangeable collecting conta iner . On Iy
in Jhe event that fine dust is to be removed
at the same time, is the illustrated paper
collecting bog also inserted. This bog pro-
tects the cloth filter from contamination .
Interchangeable collecting container
wie.und kg.
0902 73
page 4
INSTRUCTIONS FOR THE OPERATION AND MAINTENANCE OF
INDUSTRIAL CLEANER MODEL SN 2000-U
2. Suctioning into the paper collecting bog
The paper collecting bogs are used for the suctioning of fine dust and bulk material.
The disposable collecting bogs make possible the dust-free emptying.
In order to be able to suck the fine dust directly - without ~he interchangeable collecting
container - into the paper collecting bog, the collecting container must be removed, the
rubber cap (Part No. 150-029) fitted to the immersion tube and the insertion ring (Part
No. 250-(66) paced into position.
The following measures must be carried out:
2.1 The rubber cap (Part No. 150-029) is fitted to the immersion tube of the mechanical
preseparator.
2.2 The paper collecting bog (Part No. 250-(61) is inserted into the cloth filter (Part
No. 250-030) in such a way tOOt it is in contact with the cloth filter over its entire
surface area. Any folds formed during this process are smoothed out by hand.
l
2.3 The paper filter bag (Part No. 250-061) is inserted through the insert ring (Part
No. 250-(66) and folded over the edge of the main filter housing.
Remova I of the filled paper collecting bog:
2.4 The mecOOnical preseparator is tilted bockwards.
2.5 The paper filter bog is closed.
2.6 The insertion ring is removed.
2.7 The paper filter and collecting bog, together with the cloth filter, is removed.
2.8 The paper collecting bog is removed from the cloth filter.
In order to ensure that the paper filter and collecting bog is not torn during its removal,
we would recommend placing the paper collecting bog in a perforated plastic bog (Part
No. 250-(69) which provides the paper bog with the necessary mechanical strength.
wwie.und kg.
090273
page 5
INSTRUCTIONS FOR THE OPERATION AND ~INTENANCE OF
INDUSTRIAL CLEANER MODEL SN 2000-U
Suctioning of fine dust
l
Insertion ring
Cloth filter with
holding ring
For the suctioning of fine dust, which is to be emptied packed and thus
dust-free, the rubber cap is fitted to the immersion tube and the insertion
ring positioned in the housing in place of the collecting conta iner.
With small amounts of dust, or small weight, the paper collecting OOg can
be inserted directly. For large quantities or considerable weight of dust,
tearing of the paper collecting OOg is avoided by using a perforated PVC
bag. This plastic OOg is inserted first and the paper collecting OOg is
Immersion tube closed off with rubber cap
necessary during direct suction ing into the
paper collecting OOg without interchangeable
collecting container.
inserted into it. On removal, the paper collecting OOg is closed by folding
inwC?rds, and removed together with tpe PVC OOg. This latter can be used
aga m •
Immersion tube closed
with rubber cap
Paper collecting
OOg
Insertion ring
Perforated PVC OOg for providing
the paper OOgwith mechanical
strengthen ing
Insertion ring, necessary for direct
suctioning into the paper OOg
Rubber cap for closing off the immer-
sion tube - only in case of direct
suction ing into the paper collecting
OOg without a collectmg container.
Additional device for direct suction ing
of dust in to paper co 11ec ting bags for
dust-free empty;ng, see next page.
wwieland kg.
0902 73
page 6
INSTRUCTIONS FOR THE OPERAnON AND MAINTENANCE OF
INDUSTRIAL CLEANER MODEL SN 2000-U
3. Connection for hose
The 50 mm suction hose of the apparotus is fixed to the suction connection and is held
in place byan inserted rubber ring (O-ring, Part No. 500-005). The suction hose
can be fitted and removed easily by employing a rotating movement. It cannot be fitted
or removed by simply pressing home or pulling. The rubber ring (O-Ring) in the suction
connection must be replaced if damaged after lengthy use.
With the aid of the coupling piece No. 32/50 (see list of accessories), two or more
suction hoses can be coupled together.
Maintenance of the ae....e.aratus
a) The mechanical preseparotor (Part No. 150-120) must be checked from time to time
for deposits and cleaned.
b) The cloth filter (Part No. 250-030) must be cleaned when dirty and tested for possible
leakage.
c) The gaskets should be checked at regular intervals to see that they are still undamaged.
Damaged gaskets must be replaced.
Parts subiect to wear and tear
Flat belt
C 10th filter
O-ring
Gasket (holding ring)
Gasket (cyclone)
Paper collecting bog
PVC bog, perforo ted
Source of faults
1. Suction hose blocked or leaking
2. O-ring in the suction connection worn
3. Gaskets porous or defective
4. C10th filter blocked
Part No. 300-520
Part No. 250-030
Part No. 500-005
Part No. 250-032
Part No. 150-014
Part No. 250-061
Part No. 250-069
5. Flat belt loose
090273
page 7
OPERATION AND t-M INTENANCE OF INDUSTRIAL CLEANER MODEL SN 2000-U
LIST OF SPARE PARTS
Part No. Designation
100 - 005
150 - 009
150 - 014
150 - 017
150 - 120
150 - 022
150 - 029
150 - 047
150 - 070
150 - 071
200 - 300
200 - 043
200 - 048
250 - 030
250 - 031
250 - 032
250 - 033
250 - 066
300 - 620
300 - 260
300 - 108
300 - 500
300 - 501
300 - 520
Fra me
Cyclone
Gasket
Locking device, compl.
Separator, complete
Handle
Rubber cap
Separator jacket
Suction connection
Gasket
Main filter housing
Handle
Exchangeable collecting container
Cloth fi Iter
Holding ring
Gasket (holding ring)
Tensioning device with lock
Insertion ring
Suspension of blower
Blower
Three-phase motor
Flat bei t pu lIey 160,0
Flat belt pulley 30,0
Flatbelt
Part No. Designation
600 - 210
600 - 300
600 - 301
650 - 150
650 - 154
650 - 122
650 - 129
Plate castor wheel
Fixed wheel
Bushing
Elbow, suction connection
Hose piece
Air outlet
Clamping clip
350 - 150
350 - 075
400 - 005
400 - 006
400 - 007
400 - 060
400 - 065
400 - 067
400 - 068
400 - 031
400 - 074
400 - 075
400 - 071
500 - 037
500 - 005
500 - 170
500 - 085
500 - 086
550 - 007
550 - 011
550 - 012
550 - 020
Silencer
Connecting hose
Supporting block for hinge
Bent piece for hinge
Spindie for hinge
Pane 11ing, above
PaneIl ing, left side
Panelling, right side
Panelling, front
Storage container
Storage container, left side
Storage container, right side
Handle
O-ring
0- ring
Rubber stop
G rommet for cable
Fixing clip
Motor protection switch
Cable 380 Volt
Calbe 220 Volt
. Plastic hose
wwie.und kg.
090273
page 8
INSTRUCTIONS FOR THE OPERATION AND N\A.INTENANCE OF
INDUSTRIAL CLEANER MODEL SN 2000-U
.•.
~
~ ~~'" ~~ ~~I~ ~?~ ~,
I
~ ~ ~I ~I~~ 0'1 ~ ~ gr ~ ~ ~I~ ~ ~ ~
Ilr1 ~~!~1!1!;'n
~
~~
I
0'
I
"
"
"
/,'
11'
I
0'
\ I II I
'"
IIIII
il
~
~
0'
I
&
~
~
~,~
~
·1
~
~
J
~
:1
~
~I
~
~
I
""
'"
0':
?I '
~
ä
J
J
111
~.
~
Qi
g
~
~I
..
~
~j
wwieland k 9 nür••berg
090273
List of accessories, conical system, " 30, 40, 50, 60 mm
When ordering hoses or suction tools, please state article number and diameter.
Possibilitiesof combination for suction hoses and suction tools
CI) Same diameter for suction hose and nozzle
Bowed pipe No. 3/50 mm 0 is attached directly to hose connector No. 31/50 mm 0.
Bowed pipe No. 3/50 mm 0
o
@ Diameter of nozzle being smaller than diameter of suction hose
Suction hose of dia 50 mm isequipped with reducing fitting No.31b/50 mm 0to reduce from 50 to 40 mm.
Then the bowed pipe No. 3/40 mm 0 can be attached.
Hose connector
No. 31(50 mm
0
cM\\\\\~
Hose connector
No. 31a/50 mm 0
with retention pin
o
Suction connection
ot machine 50 mm 0
Reducing fitting No. 31b/50
(ta reduce dia tram 50 to 40 mm)
@ Coupling of two suction hoses of equal diameter
For coupling two or more suction hoses tagether (tor extension), the hose coupler No. 32 of same
diameter is used.
2/50 mm 0
Hose connector No. 31/50 mm 0
wwie.und
P.O.Box 3669 . D-8520 Erlangen 26 (Nürnberg)
Phone 09131/60073 . Telex 629832
0181
- page 1
List of accessories. conical system, " 30, 40, 50, 60 mm
Flexible hoses
0 40 0 50 0 60 0
Article No.
Designation
30
Application
05P
05G
05M
03S
Plastic hose, 5 m long,
with connections 31, 31a
and with reducing fitting 31b
Rubber hose, 5 m long,
with connections 31. 31a
and with reducing fitting 31b
Metal hose, 5 m long,
with connections 31, 31a
and with reducing fitting 31b
Plastic hose, 3,5 m long,
with PVC-hand tube 30°.
with connection 31a
and with reducing fitting 31b
Suction pickup
and extension,
(not for blowing)
Suction pickup
or blowing and
for extension
Suction pickup
and extension
(not for blowing)
Suclion pickup
(not for blowing)
05S
Article No.
14
Plastic hose, 5 m long,
with connections 31, 31a
and with reducing fitting 31b
very flexible
Suction tools
Designation
Hose cleaning brush,
5 m long
30" I 40 0 I 50 0 I 60 0
Suction pickup
and extension
(not for blowing)
Application
Cleaning of suction
and blowing hoses
..wie.und
P.O. Box 3669 . D-8520 Erlangen 26 (Nürnberg)
Phone
09131/60073, Telex 629832
0181
- page 2
List of accessories, conical system, " 30, 40, 50, 60 mm
Article No.
Reducing fitting for
30a
suction connection of machine
Necessary when
I Reducing fitting
Hose coupler
I
Necessary when
than flexible hose
smaller 0 than hose
(for units of 7.5 HP
of smaller diameter
and more)
equipped with No 31
I
I
•
II
I
II
I Reducing fitting
using accessories
I
131b
I
working with nozzleswith air regulation
Designation
I
I
300
40 0 I 50 0 I 60 0
For extension
No. 4 and 6 of next
of suction hoses
Application
Necessary for use
of suction hoses
with smaller 0 than
standard connection
of clear.er
2" a~=~1
o/4"~
wwie.und
Drum filling device. type LE.
two parts
33
Suction tube. approx. 1m long,
plastic
Suction tube. approx. 1m long.
1a
aluminium. anodized
Suction tube. approx. 1m long.
1c
steel. zinc coated
P.O. Box 3669 . 0-8520 Erlangen 26 (Nürnberg)
Phone 09131/60073, Telex 629832
Allows to collect
liquids in closed
drums with screw
thread connection
3/4' and 2".
Required for
floor cleaning
with nozzles.
for extension of
pickup pipeline.
for cleaning walls.
ceilings. etc.
0181
page
3
List of accessories, conical system, " 30, 40, 50, 60 mm
0 I 40 0 I 50 0 I 60 0
Article No.
Suction tube, approx. 0,5 m long,
Suction tube, approx. 0,5 m long,
Suction tube, approx. 0,5 m long,
I
I
Elbow 90°, turning,
11
I
-
steel, zinc coated
aluminium, anodized
metal, lacquered
plastic
2a
2c
I
. turning
•
I
5a
-
steel, zinc coated
2 parts, plastic
plastic
metal, lacquered
plastic
3a
3
4
Suction nozzle 30°,
Send pipe 90°,
Send pipe 90°,
Sowed pipe 30°,
I
I
I
I
2
Sowed pipe 30°,
5
I
I
Designation
30
Application
For suction pickup
and extension
of pipeline
Forsuction
connection of the
unit. Prevents a
buckling of the hose
Cleaning of beams
or pipings
(in connection
with brush)
7~'7
t:~:::1'::::===:::'
~
7g
• ..., '" J)'.",,- I 7b
~17'
~": '.,
., .7b
"~;l\
•
I 7g
Suction nozzle 30°,
4a
one piece,
metal, lacquered
Flat nozzle (crevice tool)
plastic
030 = 12x50 mm
6
040 = 12X65 mm
= 1BX90 mm
050
Flat nozzle (crevice tool)
metal, lacquered
030 = 10x50 mm
6a
040 = 15X60 mm
050 = 15XBO mm
060= 15Y90mm
Triangular nozzle, angular,
aluminium casting, lacquered,
150X15 mm
Triangular nozzle,
angular, with steel scraper,
aluminium casting, lacquered,
150X15 mm
Triangular nozzle,
angular, with rubber lips
aluminium casting, lacquered,
150X 15
Suction nozzle and
connection piece
för brushes,
tubes and nozzles
For suction pickup
or blowing, for
machinery cleaning
(lubricating holes)
Cleaning of narrow
spaces on machines
and radiators
Removal of dirt
Scraping off and
suction pickup
of adherent dirt
Removal of
liquids and sludge
wwie.und
Triangular nozzle,
angular, with brush part,
aluminium casting, lacquered,
150X15 mm
P.O. Box 3669 . 0-8520 Erlangen 26 (Nürnberg)
Phone 09131/60073, Telx 629832
Cleaning of bolsters,
inside cleaning
of cars
0181
page
4
List of accessories, conical system, " 30, 40, 50, 60 mm
30 0
Article
No.
Designation
I 40 0 150 0 I 60 0
Application
Triangular nozzle, straight,
7c
aluminium casting, lacquered,
110X30 mm
Triangular nozzle, angular,
7d
aluminium casting, lacquered,
300X28 mm
Triangular nozzle,
angular, with rubber lips,
7e
aluminium casting, lacquered,
300X28 mm
Triangular nozzle, straight,
7t
aluminium casting, lacquered,
276 mm large
Brush, cross, angular
040
8
= 250 mm large
o 50 = 370 mm large
Suction pickup ot
dirt, turnings and
bulk material
Removal of
dirt and turnings
Removal ot
liquids and sludge
Suction pickup
ot turnings,
tloor cleaning
Removal ot dry dust
trom walls and
other surfaces
-----~--
\
~
---
-
-
-
Brush, round,
with angular neck,
10
o 40 = 100 mm
o 50 = 120 mm
Brush, curved,
12a
1200 bowed,
tor pipelines up to 250 mm 0
Brush tor tlues
15
(when ordering,
state 0 of flame tubes)
Brush tor tlues,
electromechanical
cleaning pistol
16
(when ordering, state 0
ot tlo.me tubes)
Special nozzle tor the cleaning
ot blind holes with suction tube
40
2a/50 mm 0 (incl. connection
tor comp'ressed air, 5 blowing
nozzles, compressed air valve)
see separate quotation
Cleaning ot surfaces
on machines,
ceilings, windows,
columns and beams.
Cleaning ot piping
Cleaning ot
tlame tubes
Cleaning of
flame tubes
Suction/blowing
nozzle tor the
cleaning 01 blind
holes
.,i.land
P.O. Box 3669 . D-8520 Erlangen 26 (Nürnberg)
Phone
09131/60073· Telex 629832
0181
page 5
List of accessories, conical system, " 30, 40, 50, 60 mm
Universal rubber brush,
500 mm wide
700 mm wide
Floor cleaning
wet and dry
300 mm wide
Article
~ ~:-..:JI 39
Designation
26
Additional air nozzle,
steel, lacquered
Application
cleaning looms and
dust and fly,
I
other machinery
Removal of
Removal of
uulk material
and accumulations
of dust
Technical modifications reserved.
Flexible tube nozzle,
approx. 0,5 m long
Rubber nozzle,
29
approx. 150 mm long
Rubber nozzle,
29a
approx. 150 mm long,
with scraper
Electrical hour recorder
23
Slipring cable drum,for winding
cable without disconnecting from
elec. supply with 20 m cable
28a
NMHöu 4X 2,5
with 20 m cable
NMHöu 4X4
with 15 m cable
NMHöu 5X4
mm2 (without plug)
mm2(without plug)
mm2 (without plug)
Machinery cleaning,
especially for
delicate parts
Machines cleaning
Machines cleanmg.
pickup of dirt
and turnings
from grooves
For the control
operating hours
cable extension
01
wwie.und
P.O.Box 3669 ' D-8520 Erlangen 26 (Nürnberg)
Phone 09131/60073, Telex 629832 _
0181
page 6
All the suction power you need: 2 - 300 kW
Industrial vacuum cleaners
Traileror truck-mounted vacuum loaders
Stationary suction and vacuum conveying plants
Dust extractors
5-1000
Single-phase
Three-phase AC
2,2 kW /3 hp
Light-weight, high-
performance industrial cleaner for
wet or dry material.
5N - 2000
Three-phase AC
2,2 kW / 3 hp
for dust and chippings;
80 Icollection container.
15-150 R
High-performance suction unit for
sand. chippings. fine dust; removes
up to 4 tons/h; electric filter clean-
ing; 160 I interchangeable collection
container.
Max Vac
11
Drum-type industrial
vacuum system.
adaptable to your
specific requirements: available with
a choice of performances and filter
systems.
Three-phase AC
11kW /15 hp
kW /15
hp
Three-phase AC
Compressed air7,5 kW /10
5 - 3 and 5 - 3/30
The most compact
Three-phase AC
Compressed air
18,5 kW / 25 hp
22 kW / 30 hp
and versatile cleaner
with positive-displacement vacuum
pump (one year maintenance-free);
removes 10 tons/h bulk material,
turnings. catalyst, sludge. liquids.
hp
Model series
VACTRAILER
Electric
Diesel
37 kw=303 kW
50-412hp
Available with
55% or 80% vacuum pump. Air
delivery rates up to 15000 m3/h.
loading rates up to 100tons/h.
Suction inlet dn 15O-300mm.
15-30and 15-30/80
Three-phase AC
Compressed air
2,2 kW / 3 hp
tor dust and liquids;
50 land 80 I removable collection
container; high-efficiency filter
system. Separation of turnings and
liquids possible.
15-75R / 15-100R
Three-phase AC
5,5 kW / 7,5 hp
7,5 kW /10 hp
Designed tor fine
dust. chippings, liquids, remove up
to 2 tons/h, 100 Iinterchangeable
collection containers.
D5-1 / D5-2
Rugged. 80% high
Three-phase AC
Compressed air
4 kW / 5,5 hp
5,5 kW /7,5 hp
vacuum suction
cleaners for machine cleaning;
oil. chippings. sludge removed in
seconds; 100 I interchangeable
collection containers.
AP-75R / AP-75RP
Three-phase AC
7,5 kW /10 hp
Identical performance as OS - 2;
sound-prooted to 74-78 dB(A);
high-efficiency filter. suitable for fine
dust.
CONTAINERVAC
Diesel
120k"W7i60 hp
Truck-mounted vacuum loaders with
separate diesel engine 160hp.
vacuum pump 50 or 80%, air delivery
rate 6800m3/h.
Suction inlet dn 200 mm.
VACTRUCK-
1600P-5C
Diesel
205 - 235 kW
280 - 320 hp
Removes fine dust.
lumps, sludge. liquids, also suitable
for poisonous dust. Loading rate up
to 60 tons/h, suction distance up to
200 m. Uses truck engine as power
supply.
KS-CENTRAL
~Iectric
18,5kW -110 kW
25 hp - 150 hp
Vacuum cleaning and conveying plants,
compact design, liHle maintenance required. Suction
distances more than 200 m on either side. Suction inlet
dia. 40 - 200 mm.
Performance rate up to 60 tons/ho
monobloc
Three-phase
0,75 kW - 4 kW
1 hp - 5.5 hp
Low-priced individual or group extraction
units for grinders, saws, polishers, special version for bag
collection available, also suitable für dust hazardous to
health.
Portable and stationary intercept hoppers and
filter/hoppers separate the suctioned material from the
conveying air. Capacity 1- 20
devices available.
Rotaryvane vacuum pumps
Up to 95% continuous
vacuum, für use in high-per-
formance cleaners, e. g. our
OS/AP portable suction
cleaners. Used where heavy
material has to be con-
m3; various discharge
Radial suction blowers
Low-priced, can be applied
as single-stage units, up to
1500 mm
stage blowers produce a
vacuum of up to 3500mm
W.g.
W. g. Gur multi-
veyed over long distances,
or where high extraction
power isrequired.
High-performance dust extractorsPortable and stationary intercept hoppers.
Filter units with automatie filter cleaning, ~
mechanical or pneumatic, up to 40
m2 filter area.
ö
Side-channel
vacuum pumps
The optimal units for tasks
requiring a vacuum of
20-40%; can also be used
as compressors. Very quiet,
maintenance-free, suitable
for continuous operation,
employed in Max Vac units
and KS-CENTRAL.
Positive-displacement
vacuum pumps
Oesigned for a very long
service life. Gur standard
vacuum pumps operate in
the 55% vacuum range.
Gur special (R-type) pump
produces 80% vacuum,
air delivery rates up to
15000m3/h. This pump is
used for those really tough
suction conveying jobs.
Electric
1,5 i(W":11kW
2,2 hp -15 hp
wwieland lu"l'•• echnik gllnbh P.O. Box 3669, D-8520 Erlangen 26· Phone 09131/60073, Telex 629832
Loading...