Wiedamark 6IN1 LED PAR Instruction Manual

66IINN11 LLEEDD PPAARR

INSTRUCTION MANUAL

INSTRUCTION OF BUTTONS

DESCRIPTION OF MENU

STAT FUNCTION

- Choose [STAT] and press [ENTER] to “stat mode” ( manual mode )

- Press [ENTER] to choose : [Red], [Green], [Blue], [Amber], [White], [Strobe]

- Press [UP] / [DOWN] to choose the value ( 0 to 255 for level of each color and 0 to

20 for frequency of strobe )

- Press [MENU] back to the main menu

AUTO FUNCTION

- Choose [AUTO] press [ENTER] toenter I auto mode

- Press [UP]/[DOWN] to choose the built-in program or edit program ( AT01 to AT10

programs cannot be modified by edit function / PR01 to PR10 programs can be modified

by edit function )

- Press [MENU] Back To The Main Menu

DMX FUNCTION ( DMX ADDRESS SETTING )

- Choose [DMX] press [ENTER]

- Press [UP]/[DOWN] to choose [1~512] value

PERS FUNCTION ( DMX OPERATING MODE )

- Choose [PERS] and press [ENTER]

- Press [UP]/[DOWN] to choose the dmx channel modes, (for details, please check on the

dmx channels on the following)

ID FUNCTION

- Choose [ID] and press [ENTER]

- Press [UP]/[DOWN] to choose [1~255] value

EDIT FUNCTION

Key code : UP, DOWN, UP, DOWN + ENTER

UP : Use to choose operating mode, DMX address or to set parameters

DOWN : Use to choose operating mode, DMX address or to set parameters

ENTER : Use to validate your choice

MENU : Use to select a function or to come back to the previous menu

MENU ENTER UP DOWN

- Choose [EDIT] and press [ENTER]

- Press [ENTER] to choose the parameter values

- Press [UP] / [DOWN] to choose program, scene or parameters values ( red [R), green [G], blue [B], white [W], amber

[A], strobe [S], time [T] and fade time [F] )

Sound FUNCTION

( Sound control Strobe)
( Sound control brightness)
( Sound control color changing)

SET FUNCTION

- Choose [SET] and press [ENTER]

- [UPLD] : sending edit program value from current master unit to slave

unit : To do it, press [ENTER] then do the key code [UP, DOWN, UP,

DOWN] and press [ENTER], light turn to yellow, means data was

sending meanwhile there will show the speed of upload, light will turn

to green when finished sending, and the slave unit will turn to yellow

too when receive the data,and turn to green when finished receiving. if

the slave unit protect to yellow,it means fail receiving, please cut off

the power and receive again.

- [REST] : To load the factory setup.

- Press [ENTER] and do the key code : [UP, DOWN, UP, DOWN] then press [ENTER]

- [ID] : ID address setting, Press [ENTER], press [UP] / [DOWN] to choose [ON] to allow ID address function, [OFF] close

ID address function

- [RGBW] : color deviation correcting setting, Press [ENTER], press [UP] /[DOWN] to choose [ON] to allow color

deviation correcting function,[OFF] not allow. the proportion of RGBW colors can be set in the menu [CAL2]

- [DIM] : non-linear dimming setting, Press [UP] /[DOWN] to choose : [OFF] close dim speed, [DIM1] to [DIM9] to

choose speed ( speed 1 (fast ), ….., speed4 (slow), as the speed is slower as dimming softer.

- [DV] : Digital photography color choosen, Press [ENTER], and use [UP] /[DOWN] to choose between [NTSC] or [PAL]

CAL1 FUNCTION ( WHITE BALANCE FUNCTION )

- Choose [CAL1] and press [ENTER]

- Press [UP] /[DOWN] to choose [WT1~11] then press [ENTER] to set up to 11 different temperature of white color