WiebeTech ProSATA SS8 Quick Start Manual

Page 1
Quick Start Guide
Table of Contents
Introduction 1 Installation 2
Box contents 2
Identifying the parts of the ProSATA SS8 2
Installing hard drives 3
Using the configuration GUI 3
Creating RAIDs and volumes 4
Connecting to the SCSI host 5
Working with volumes over 2TB in size 5 Warnings and Notices 6 Frequently Asked Questions 7 Technical Specifications 8 Warranty Information 8
SS8
Revised January 23, 2008
Introduction
Thank you for purchasing WiebeTech’s ProSATA™ SS8, a high-performance RAID subsystem with the ultimate in data-protection capabilities! This Quick Start Guide covers the essentials for getting your ProSATA up and running quickly. For more comprehensive technical
information, see the full user manual on the CD accompanying this product.
P r o S A T A S S 8 Q u i c k S t a r t G u i d e - 1 -
Page 2
WiebeTech LLC
Access LED
Power Input
Power Switch
RS-232 Port
SCSI to Host
Terminator
Ethernet Port
Installation
Step 1: Unpack
Unpack and install the hardware in a static-free environment. The ProSATA SS8 is packed inside an anti-static bag between two foam supports. Remove it and inspect it for damage. If the unit appears damaged, or if any of the contents listed below are missing or damaged, please contact your dealer or distributor immediately.
Checklist
The ProSATA SS8 kit should include the following items:
ProSATA SS8 unit 8 removable drive trays (inside the foam above the unit). These will be pre-configured with drives if so ordered Packet of keys and screws SCSI terminator RS232 cable Power cord User’s manual and warranty statement (on CD)
In addition to these things, you’ll also need a SCSI host card installed inside your computer, and a SCSI cable to connect the ProSATA to the card. Note: The ProSATA SS8 uses an HD68 type SCSI connector.
If you purchased the ProSATA SS8 in the full bundle configuration, the card and cable are included.
Step 2: Identify the parts of the ProSATA SS8
Front View of ProSATA SS8: Back View of ProSATA SS8:
P r o S A T A S S 8 Q u i c k S t a r t G u i d e - 2 -
Power LED
Voltage Switch
Page 3
WiebeTech LLC
Bottom View of ProSATA SS8: Removable drive trays:
Serial Number
LCD Control Module
If you purchased your ProSATA SS8 with pre-configured drives, you may skip ahead to the last step: Connecting to the SCSI host.
Step 3: Install SATA drives
If you purchased the ProSATA SS8 without hard drives pre-installed, please follow the instructions below to install your own drives.
1. Loosen the ProSATA’s front panel using the two built-screws, and then open it.
2. Remove a drive tray from the foam packaging. If the trays are already inside the ProSATA unit, gently remove one tray at a time by pressing the release button and then pulling the handle. You may need to unlock the trays first using the key provided.
3. Insert the drive into the tray with the connectors directed toward the open rear of the tray.
4. Align the mounting holes of the drive with the tray.
5. Secure the drive to the tray with the included screws.
6. Slide the drive tray back into the empty slot of the ProSATA SS8. Make sure the handle clicks into place.
7. Once it is seated firmly, you may lock the tray with the included key for added security.
8. Repeat these steps for each of the other drive trays.
9. After installing all the drive trays, close the ProSATA’s front panel and secure it using the two built-in screws.
Step 4: Use a web browser to access the GUI
1. Connect the power cord to the ProSATA. Plug the other end into a grounded electrical outlet. Do not turn on the power yet.
2. Connect the ProSATA unit to your network or directly to your computer using an ethernet cable. If connecting to an ethernet hub, use a straight ethernet cable. If connecting directly to your computer, use a crossover cable.
3. Turn on the ProSATA.
4. Place the ProSATA on its left side (looking at it from the front), so you can access the LCD interface.
5. Check the LCD to see what IP address the ProSATA is using.
The remaining instructions for this step vary slightly depending on your ethernet setup.
P r o S A T A S S 8 Q u i c k S t a r t G u i d e - 3 -
Page 4
WiebeTech LLC
Connecting to a DHCP-enabled network
On DHCP networks, a new IP address is dynamically assigned to the ProSATA SS8 as soon as the network detects it. Simply type this IP address into a web browser on your computer. This will access the ProSATA’s GUI, which you will use to configure the unit.
Connecting to a static network or directly to a computer
1. Check your computer’s IP address. To do this in Windows, open Network Connections in the Control Panel. Double click on your network and then click on the Support tab. Your computer’s IP address will be displayed.
2. On the ProSATA’s LCD interface, press ENT and then scroll up or down to Change IP
Setting.
3. Press ENT and find Static.
4. Press ENT again and change the IP address to closely match what your computer is using. For example, if your computer's IP address is 192.168.000.009 you could change the ProSATA's IP to 192.168.000.007. Everything but the last set of three digits must be the same! When changing the IP address you'll notice that a box flashes over the digit to be changed. While the digit is selected, press up or down to change it. Press ENT to move to the next digit. After the IP is set, press ENT all the way to the end and confirm the settings change. To confirm, press up for yes and then press ENT again.
5. Type the ProSATA’s new IP address into a web browser on your computer. This will access the ProSATA’s GUI, which you will use to configure the unit.
Not sure what type of network you have?
If the IP address displayed on the LCD starts with 169.254 or 192.168, this indicates that the network is probably not DHCP-enabled. Use the instructions for a static network.
Step 5: Configure the RAID
You will use the built-in browser-based GUI to set up a RAID and create logical volumes on the ProSATA. To launch the GUI, open a web browser on your computer and then type the ProSATA’s IP address into the URL bar. (See previous step.)
The GUI’s main page should load, displaying a picture of the ProSATA with several options to the right. When you click on any option, you will be prompted for a user name and password. The user name is "admin" and the default password is "1234."
1. Click on Volume Group, then Volume Config.
2. Choose New. Select the RAID level you would like to use (usually RAID 5). If there is an error saying "Disk is not enough" you'll need to go to Physical Disk, select all of the disks you wish to include in the Volume group, and press the "Free Disk" button.
3. Click on Select PD. Select all the hard drives you wish to put into the new RAID set. You’ll need to confirm your choice.
4. Now go to User Data Volume and choose New. Select the capacity you want for this UDV (User Data Volume).
NOTE: If the total capacity of your volume exceeds 2TB, it is likely you will encounter problems using that volume on most current operating systems. If that is the case, you will most likely wish to divide the capacity into two or more volumes of less than 2TB each. Please see the section labeled, "Working with volumes > 2TB."
P r o S A T A S S 8 Q u i c k S t a r t G u i d e - 4 -
Page 5
WiebeTech LLC
5. The rest of the details can be left at the default setting. You’ll need to confirm several times.
6. You should wind up back at the main UDV screen. Select the check box next to the UDV you just created and then click Attach LUN.
7. Use the default settings on the next few screens. You’ll need to confirm several times.
8. The RAID will begin initializing. You'll need to wait for this process to finish. Depending on the RAID type and size, this could take several hours.
Step 6: Connect the ProSATA to your SCSI host
1. Connect the power cord to the ProSATA. Plug the other end into a grounded electrical outlet.
2. Connect the ProSATA unit to the SCSI host card in your computer.
3. Connect the SCSI terminator to the other SCSI port on the back of the ProSATA.
4. Turn on the ProSATA’s power.
Installation is now complete. If you did not purchase the ProSATA with preconfigured drives, you will need to format the volume(s) before using them.
NOTE: If you're using a card that would normally support RAID functionality, you will need to disable any and all RAID settings on the card for the ProSATA to be detected. If you cannot disable the RAID settings, select JBOD mode.
Working with Volumes over 2TB in size
Although the ProSATA SS8 can create volumes larger than 2TB, operating systems cannot usually access such volumes. This is because most systems support only 32-bit LBA (Logical Block Addressing).
Newer operating systems (Windows Server 2003, Vista, Mac OS 10.5.x) should be able to use 2TB+ volumes without difficulty. You will simply need to do one of the following two things while creating the UDV (User Data Volume):
Change the LBA to 64-bit
Increase the block size to 4096
Neither option will work for Windows versions before Server 2003. You will need to make more than one UDV, giving each a different LUN. To do this, simply change the capacity when creating the UDV.
Although Mac OS 10.4.x supports only 32-bit LBA, increasing the block size to 4096 will allow you to create a 2TB+ volume that is usable by the OS.
Versions of Linux vary, but using one of the above methods may allow you to create a 2TB+ volume that your distribution can use.
P r o S A T A S S 8 Q u i c k S t a r t G u i d e - 5 -
Page 6
WiebeTech LLC
Warnings and Notices
Use only hard drives that are in perfect condition. Avoid using drives that have ever
developed bad sectors during previous usage. This could lead to possible device failure or loss of data.
The ProSATA SS8 supports SATA hard drives of various specifications and different
capacities. However, we recommend using drives of the same brand and type for optimal performance. If drives of different capacities are used, the capacity of the smallest drive will determine how much of each drive is used. The additional capacity on the larger drives will not be used by the RAID.
RAID level 0 will allow you to use the full combined capacity of the drives, and offers the
best data transfer speeds. However, RAID 0 offers no protection for the data. If one drive fails in a RAID 0, the data on all of the drives is irretrievably lost. Before creating a RAID, investigate the various RAID types and choose the one that is best for your needs.
Before starting any type of hardware installation, please ensure that all power switches
have been turned off and all power cords have been disconnected to prevent personal injury and damage to the hardware.
To avoid overheating, ProSATA SS8 should be operated in a well-ventilated area and in
such a way that sufficient airflow is maintained across the controller chips.
Static electricity can damage electronic components. To guard against such damage:
o Work in a static-free environment o Wear a grounded anti-static wrist strap o Store uninstalled components in anti-static bags o Handle PCBs by their edges and avoid touching chips and connectors.
P r o S A T A S S 8 Q u i c k S t a r t G u i d e - 6 -
Page 7
WiebeTech LLC
Frequently Asked Questions (FAQ)
Q: I've connected my ProSATA SS8 and can see the drives using the Web-based GUI, but I can't add the drives to a volume group. What's wrong?
A: Before drives can be added to a volume group they must be set to the status "Free Disk". To do this,
browse to the "Physical Disk" page under the "Volume Config" heading. From here select the drives you would like to use and click "Free Disk". Once you've done that you should be able to configure the Free Disks into any setup you like.
Q: My ProSATA does not mount when I turn it on.
A: Because the ProSATA utilizes an internal operating system, it's important to let it completely initialize
before mounting the drive to a computer. The ProSATA should take 2-3 minutes to initialize each time you start it up. The unit will let you know this process is complete with a short, 3-toned beep code (high­low-high). After the beep code sounds, you will need to restart your computer before the ProSATA will mount. Your computer's OS should detect the SCSI device during boot up and your ProSATA should be mounted and ready for use once you reach the desktop.
Q: Can I remove the sides for better access?
A: Some users of the ProSATA may want to remove the side panels of the unit to allow for better access
to internal components. However, doing this puts the unit at risk of overheating. Without the sides in place the fans are unable to provide the proper air flow necessary to keep the drives cool. When the unit is fully assembled, the fans are able to create a wind tunnel effect that constantly pushes fresh air through the unit and over the drives, keeping them from overheating.
Q: What happens when the beep alarm goes off?
A: If the unit starts to emit a regular beeping alarm, this is probably caused by a problem with the fan.
Check the fan to make sure it is spinning. If so, make sure the wires connected to the fan are fully connected and are not caught in the fan's blades.
Q: What type of cable connector plugs into the Ultra-320 SCSI port on the back of this product?
A: The Ultra-320 SCSI port on the ProSATA SS8 is of the HD68 (female) connector type. A SCSI cable
with a HD68 male connector will plug into the ProSATA.
Q: I set up my ProSATA with a volume larger than 2TB, but when I connect to the Mac to format, Disk Utility shows the volume as exactly 2TB.
A: This problem has to do with the block size that the ProSATA's volume is using. This option is set
during the creation of a User Data Volume. The only way to change the block size is to delete the current UDV and re-create a new one. Use block size 4096 for volumes larger than 2TB and your Mac should have no trouble seeing the full capacity.
Q: Can I move my drives from one ProSATA SS8 to another?
A: Changing a set of trays/drives from one ProSATA to another is tricky. You must reattach the LUN
(Logical Unit Number) in the GUI after swapping the drives. LUN is the identifying number assigned to a UDV (User Data Volume) that allows the host system to distinguish between different UDVs.
P r o S A T A S S 8 Q u i c k S t a r t G u i d e - 7 -
Page 8
WiebeTech LLC
OS Independent &
Technical Specifications
Product Name/Code Supported RAID Levels Host Interface Drive Compatibility RAID Processor Memory RAID Management Remote Management
ProSATA (SS8)
RAID 0, 1, 0+1, 3, 5, 6 & JBOD
Ultra320 SCSI
SATA1 and SATA2 hard disk drives
Intel IOP80331 500MHz 64-bit RISC Processor
512MB DDR333 DIMM
Web browser & SNMP
Via Ethernet Port
Transparent Security
LED Indicators
Thermal Monitoring Cooling Fan
Yes
Separate key lock for each HDD Drive failure indicator for each drive
Drive access indicators for each drive Built-in heat and fan sensor with mutable alarm
1 x 8cm Hot-Swappable fan Input Range: 100 to 240 VAC. 10%
Power Supply (300W)
Voltage: +5V/25A +12V/10A 47-63Hz Agency Approval: EMI/RFI, CE, FCC B, BSMI Safety: UL, CUL, CB, TUV, CCC
Operating Temperature Non-operating Temperature Operating Humidity
Supported Operating Systems
Shipping Weight Dimensions Certification
10°C ~ 35°C (50°F ~ 95°F)
10°C ~ 50°C
5% to 95% noncondensing Windows 98, NT, 2000, Millennium, XP, 2003
Mac 9.1 and above, including OSX, OSX Server, XSERVE Linux (all latest builds) which support SCSI.
32 pounds = 14.51kg (with drives)
12" x 6" x 17.5" (H x W x D)
FCC, CE 3-year limited warranty with advance replacement within first 90 days
Warranty
after purchase. See warranty statement for details and limitations. 90 days of free phone support. For support by email, contact
support@wiebetech.com.
ProSATA is a trademark of WiebeTech LLC. Other marks are the property of their respective owners. © 2006 WiebeTech LLC. All rights reserved.
FCC Compliance Statement: “This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.”
FOR HOME OR OFFICE USE
Tested to comply
with FCC standards
In the event that you experience Radio Frequency Interference, you should take the following steps to resolve the problem:
1) Ensure that your unit is plugged into a grounded electrical outlet, on a separate circuit from the affected equipment.
2) Use cables with RFI reducing ferrites on each end.
3) Use a power supply with an RFI reducing ferrite approximately 5 inches from the DC plug.
P r o S A T A S S 8 Q u i c k S t a r t G u i d e - 8 -
Loading...