WiebeTech ADAv4-18-TOSH, ADAv4-25, ADAv4-18-TOSH-ZIF, ADAv4-DOM, ADAv4-HIT-ZIF User Manual

V4 Combo Adapters™

User’s Manual

Thank you for purchasing a WiebeTech v4 Combo Adapter. Find your adapter on the list below and follow the
instructions to quickly connect and access a hard drive.

Name: v4 Adapter for SATA drives
Part Number: ADAv4-SATA
Usage: Any 2.5-inch or 3.5-inch SATA (Serial-ATA) drive
Instructions:

1. Attach the dock’s 4-wire power connector to the Adapter then connect the dock’s IDE ribbon cable to the

Adapter’s 40-pin IDE interface.

2. Connect the drive to the adapter.

3. Plug the AC adapter into the dock.

4. Connect the FireWire or USB2 cable to the computer, and then to the dock.

5. Turn on the dock’s power switch. The drive connected to the adapter will spin up and you will be able to

access it on your computer.

Name: v4 Adapter for 2.5-inch PATA drives
Part Number: ADAv4-25
Usage: Any 2.5-inch PATA (Parallel-ATA) drive, the size commonly found in laptop

computers. PATA drives are also sometimes referred to as IDE, ATA, or ATAPI, and
are identified by their 44-pin interface.

Instructions:

1. Attach the dock’s 4-wire power connector to the Adapter then connect the dock’s IDE

ribbon cable to the Adapter’s 40-pin IDE interface.

2. Lay the drive onto the adapter’s green board between the metal guide posts. Slide the drive forward until

the drive’s interface pins plug into the adapter.

3. (Optional) If you will be moving the adapter while the drive is connected, you may use the included screws

to fasten the drive to the board.

4. Plug the AC adapter into the dock.

5. Connect the FireWire or USB2 cable to the computer, and then to the dock.

6. Turn on the dock’s power switch. The drive connected to the adapter will spin up and you will be able to

access it on your computer.

Name: v4 Adapter for 1.8-inch Toshiba Drives
Part Number: ADAv4-18-TOSH
Usage: 1.8″ Toshiba drive, commonly found in iPods (1
Instructions:

1. Attach the dock’s 4-wire power connector to the Adapter then connect the dock’s

IDE ribbon cable to the Adapter’s 40-pin IDE interface.

2. Connect the drive to the Adapter, label-side down.

3. Plug the AC adapter into the dock.

4. Connect the FireWire or USB2 cable to the computer, and then to the dock.

5. Turn on the dock’s power switch. The drive in the Adapter will spin up and you will be able to access it.

Revised May 19, 2008

st

to 4th generation).

User’s Manual for WiebeTech Combo Adapters

WiebeTech LLC

Name: v4 Adapter for 1.8″ Hitachi ZIF Drives
Part Number: ADAv4-18-HIT-ZIF
Usage: 1.8″ Hitachi Zero Insertion Force (ZIF) drive.
Instructions:

1. Attach the dock’s 4-wire power connector to the Adapter then connect the

dock’s IDE ribbon cable to the Adapter’s 40-pin IDE interface.

2. Connect the drive to the Adapter by lifting up the tab and placing the ZIF cable

under the tab then close the tab.

3. Plug the AC adapter into the dock.

4. Connect the FireWire or USB2 cable to the computer, and then to the dock.

5. Turn on the dock’s power switch. The drive in the Adapter will spin up and you will be able to access it.

Name: v4 Adapter for 1.8″ Toshiba ZIF Drives
Part Number: ADAv4-18-TOSH-ZIF
Usage: 1.8″ Toshiba Zero Insertion Force (ZIF) drive, commonly found in

iPods (5

th

and 6th generation) and some laptop computers.

Instructions:

1. Attach the dock’s 4-wire power connector to the Adapter then connect the

dock’s IDE ribbon cable to the Adapter’s 40-pin IDE interface.

2. Connect the drive to the Adapter by lifting up the tab and placing the ZIF

cable under the tab then close the tab.

3. Plug the AC adapter into the dock.

4. Connect the FireWire or USB2 cable to the computer, and then to the dock.

5. Turn on the dock’s power switch. The drive in the Adapter will spin up and you will be able to access it.

Name: v4 Multi-Card Adapter Bundle
Part Number: ADAv4-MCB
Usage: PCMCIA (PCCARD) drives, MMC/SD, CompactFlash I/II, Sony

Memory Sticks, and 1.0” Microdrives.

Instructions:

1. Attach the dock’s 4-wire power connector to the base Adapter (the largest of

the three pieces that comprise ADAv4-MCB). Connect the dock’s IDE ribbon
cable to the base Adapter’s 40-pin IDE interface.

2. If you are attempting to access a PCMCIA drive, connect the drive directly to the base Adapter. Otherwise,

attach the secondary adapter that is appropriate for the media type you wish to access. Use the MCB-1
adapter for Compact Flash or MicroDrives. Use the MCB-2 adapter for other media types.

3. Plug the AC adapter into the dock.

4. Connect the FireWire or USB2 cable to the computer, and then to the dock.

5. Turn on the dock’s power switch. The drive in the Adapter will spin up and you will be able to access it.

Name: v4 Adapter for Disk on Module drives
Part Number: ADAv4-DOM
Usage: Disk on Module drives.
Instructions:

1. Attach the dock’s 4-wire power connector to the Adapter then connect the

dock’s IDE ribbon cable to the Adapter’s 40-pin IDE interface.

2. Attach the Disk on Module drive to the appropriate slot on the Adapter. (There

are two different slots. Use only one at a time.)

3. Plug the AC adapter into the dock.

4. Connect the FireWire or USB2 cable to the computer, and then to the dock.

5. Turn on the dock’s power switch. The drive in the Adapter will spin up and you will be able to access it.

User’s Manual for WiebeTech Combo Adapters

WiebeTech LLC

Technical Specifications

Product Name
Product Codes:

Dock Types Supported:

Drive Types Supported:

Operating System
Requirements:

Operating Temperature:
Operating Humidity:
Safety Certification:
Shipping Weights:
Dimensions:

Warranty:

V4 Combo Adapter is a trademark of WiebeTech LLC. Other marks are the property of their respective owners.

© 2007 WiebeTech LLC. All rights reserved.

If you have any questions or problems, please contact [e-mail] for technical support. If you are interested
in purchasing more WiebeTech products, check our website or contact [e-mail]
to serve you!

V4 Combo Adapters
ADAv4-SATA, ADAv4-25, ADAv4-18-TOSH, ADAv4-18-HIT-ZIF, ADAv4-18-

TOSH-ZIF, ADAv4-MCB and ADAv4-DOM
ComboDock v4 (CDKv4)
FireWire DriveDock v4 (FWDDv4)
Forensic ComboDock v4 (FCDKv4)
Forensic DriveDock v4 (FODDv4)

ADAv4-SATA: 3.5” SATA1 or SATA2 HDD up to 1TB and 2.5” SATA HDD
ADAv4-25: 2.5” IDE/PATA HDD (also, Hitachi 1.8” IDE/PATA HDD)
ADAv4-18-TOSH: 1.8” Toshiba HDD
ADAv4-18-HIT-ZIF: 1.8” Hitachi ZIF HDD
ADAv4-18-TOSH-ZIF: 1.8” Toshiba ZIF HDD
ADAv4-DOM: Disk-on-Module HDD
ADAv4-MCB: PCMCIA (PCCARD) drives, MMC/SD, CompactFlash Type I/II,

Sony Memory Sticks, and 1.0” MicroDrives
Windows XP, Vista
Mac OS X 10.2.6 or later
Linux distributions using Kernel version 2.4 or above (USB only)

50 – 85° Fahrenheit (10 – 30° Celsius)

5% to 95%, noncondensing

RoHS

1 pound
(115mm L x 85mm W x 20mm H)

1-year limited warranty. See warranty statement for details and limitations.
WiebeTech offers free phone support for 90 days after purchase (1-866-744-

8722). After 90 days, email support is available at [e-mail].

. We appreciate being able

User’s Manual for WiebeTech Combo Adapters