Wido RTVRACK User Manual
This wall bracket is designed for wall mounting of flat panel televisions and monitors with a screen
size between 32” to 65”. It can be installed on wood stud and solid concrete walls indoors and only
within private households. It is not designed for installation for commercial purposes.
2 Safety Notes
We recommend that this product should only be installed by suitably qualified persons or
persons competent in DIY. If you are unsure of any part of the installation, please contact a
professional installer.
Never leave children unsupervised with this product or its packaging. This article contains small
parts that could pose choking hazard. Packaging materials pose suocation hazard.
Correct and safe installation is extremely important. Falls are outside the scope of responsibility of
the manufacturer. The supplied kit is designed for installation on solid wood or concrete walls. For
any other types of surfaces, assistance from professional installer is recommended.
Do not install this article in places under which people or animals may stand.
Handle the TV carefully during installation since subjecting it to impact or other forces may cause
product damage.
Carefully read the instructions accompanying optional accessories, and be absolutely sure to take
steps to prevent the TV from falling o.
Always read the section of instruction manual that came with your TV related to wall mounting as
some TV might require special fittings or installation requirements such as distance from wall.
Take care when fixing wall brackets to the wall. Always ensure that there are no electrical
cables or pipes in the wall before hanging bracket.
Before installing this article, ensure the wall is capable of supporting the combined weight of
television and bracket. Never exceed bracket’s maximum load of 35kg. Exceeding the weight
load may cause product failure.
Ensure that wall structure and fixings are capable of supporting the TV set. Check the
strength of the installed wall plate before attaching the TV with brackets onto it.
RTVRACK
Item Code:
Tilting TV Wall Bracket
Product:
1 Intended use
Read all instrucons carefully before assembling and using this
arcle. Retain them for future reference and if you are passing this
product to a third party, always make sure this documentaon is
included.
1
3 Identification of parts
There are many variants of TV sets on the market requiring dierent types of fitting. Bearing this in
mind, the kit supplied with this article might not support the TV you are trying to install.
If the bolts required for safe and proper installation of the bracket to your tv are not included, please
purchase required fittings from specialist shop.
If the bolts for attaching brackets to your TV are too long, included extension washers can be used
to reduce the length.
VESA Standard: 200mm x 200mm to 400mm x 400mm
Max. Load capacity: 35.5kg
Screen size supported: 32” to 55”
Distance from the wall: 6.5cm
Product net. weight: 2.2kg
Small Bolts x8
M5 x 24mm M4 X 24MM
M4 X 35MM
F
Washers x8
G
Long Bolts x2
H
Bracket Arms x2
I
PARTS
TOOLS REQUIRED
(Not included)
Power drill
with suitable drill bit
Pencil Cross head
Screwdriver
Hammer Stud finder
Bracket Wall Plate x1
A
Wall Plugs x4
C
Coach Screws x4
D
Plastic Spacers x4
E
Spirit Level x1
B
2
5 Installation
Before proceeding with installation, ensure you have all parts and tools required for safe and complete
installation. Check that included bolts (F) match the TV set you are going to fix.
Should the TV set require dierent size bolts to fix bracket arms, postpone the installation until you have a
complete set. Read the instruction manual that came with your TV for advice on size of bolts required.
Select suitable wall mounting height. We
recommend positioning the TV set on the eye level
from seating position in front of the TV.
Position the bracket against the wall in chosen
location, align it using the spirit level included with
the bracket. Mark four holes with a pencil.
Avoid any live, electrical, utility pipes behind the wall.
Drill holes in the marked position approx. 6mm in
diameter and 50mm deep.
Insert the wall plugs into the holes and screw the wall
bracket to the wall.
Concrete/masonry wall installation
Secure the wall plate by inserting coach screw and a
washer through the plate into wall plugs. Tighten fully
to secure.
Solid wall
(masonry/concrete)
3
1 2
3
Loading...