Wide NA42LHD, SD4200CW User Manual
USER’S MANUAL
NA42LHD (SD4200CW
)
TFT–LCD Monitor
2
Table of Contents
Safety Instructions ............................................................................. 3
Your New LCD Monitor ....................................................................... 6
Regulatory Information ...................................................................... 7
Connecting your LCD Monitor .......................................................... 9
Rear bottom view
................................................................... 9
Connecting power cord .......................................................... 9
Connecting the computer ....................................................... 9
Connecting external devices to the VIDEO(CVBS)INPUT port
..... 10
Connecting external devices to the S-VIDEO INPUT port
............ 10
Connecting external devices to the Component INPUT port
........ 10
Connecting external devices to the SDI INPUT port
.................... 11
Connecting external devices to the SOG INPUT port
.................. 11
Connecting external devices to the BNC INPUT port
.................. 12
Adjusting Your LCD Monitor ........................................................... 13
Warm-up Time
..................................................................... 13
User Controls ....................................................................... 14
OSD Function Controls ........................................................ 15
Picture .................................................................................. 15
Analog .................................................................................. 17
PIP ........................................................................................18
Setup ................................................................................... 19
Information ........................................................................... 20
Trouble Shooting .............................................................................. 21
Appendix ........................................................................................... 22
Display Modes
..................................................................... 22
Specications ....................................................................... 23
Pin Assignments .................................................................. 25
3
Safety Instructions
CAUTION
RISK OF ELECTRIC
DO NOT OPEN
AVERTISSEMENT RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
LCD MONITOR
WITH RESPECT TO ELECTRIC SHOCK,
FIRE AND MECHANICAL HAZARDS ONLY
IN ACCORDANCE WITH UL60601-1 AND
CAN/CSA C22.2 NO. 601.1,
54IJ
E217340
MEDICAL EQUIPMENT CERTIFIED FOR CANADA
Grounding Reliability Can Only Be Achieved When The Equipment ls Connected
To An Equivalent Receptacle Marked “Hospital Only” or “Hospital Grade”.
Explanation of Graphical Symbols
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of the important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
The lighting flash with arrowhead symbol, within an equilateral triangle, is intended
to alert the be user to the presence of un-insulated "dangerous voltage" within the
product's enclosure that of may sufficient magnitude to constitute a risk of electric
shock to persons.
Stand-by Switch. Press to turn the monitor on or off (Stand-by mode).
Direct Current.
Warning When the unit is used together with other equipment in the patient area, the
equipment shall be connected according to Standard UL60601-1 and IEC 60601-1.
Classication
Protection against electric shock: Class 1
Applied Parts No Applied Parts.
Protection against harmful ingress of water: ordinary IPXO.
Degree of safety in the presence of ammable anesthetics mixture with air or with oxygen
or with nitrous oxide.
Not suitable for use in the presence of a ammable anesthetics mixture with air or with
oxygen or with nitrous oxide.
Mode of operation: Continuous.
•
•
•
•
•
4
Safety Instructions
Precautions
On Safety
1. Never insert anything metallic into the cabinet openings of the Liquid Crystal Display (LCD)
monitor ; doing so may create the danger of electric shock.
2. To reduce the risk of electric shock, do not remove cover. No user-serviceable parts inside.
Only a qualied technician should open the case of the LCD monitor.
3. Never use your LCD monitor if the power cord has been damaged. Do not allow anything
to rest on the power cord, and keep the cord away from areas where people can trip over
it.
4. Be sure to hold the plug, not the cord, when disconnecting the LCD monitor from an
electric socket.
5. Unplug your LCD monitor when it is going to be left unused for an extended period of time.
6. Unplug your LCD monitor from the AC outlet before any service.
7. If your LCD monitor does not operate normally - in particular, if there are any unusual
sounds or smells coming from it - unplug it immediately am authorized dealer or service
center.
8.
Do not install this product by yourself. Contact the qualied service technician. Otherwise,
it may cause injuries.
9. Do not install this product by alone. Get some help from others. Otherwise, it may cause
the product to fall and could cause injuries.
10. The screw is not provided to user as default. Use the screw, which can stand the weight of
this product. And, we recommend the machine screw BH(+)M8 x 20mm to 16mm as type.
Warning Do not touch signal input, signal output or other connectors, and the patient
simultaneously.
Warning External equipment intended for connection to signal input, signal output or
other connectors, shall comply with relevant IEC standard (e.g., IEC60950 for IT
equipment and IEC60601 series for medical electrical equipment).
ln addition, all such combination - system - shall comply with the standard,
IEC60601-1-1,safety requirements for medical electrical system. Any person who
connectors has formed at system and is therefore responsible for the system to
comply with requirements of IES60601-1-1.
if, in doubt, contact qualied technician or your local representative.
5
Safety Instructions
This TFT LCD Monitor is as accessory intended for use with Medical
Equipment to display alpha, numerical and graphical data.
On Installation
1. Openings in the LCD monitor cabinet are provided for ventilation. To prevent overheating,
these openings should not be blocked or covered. Also avoid using the LCD monitor on
a bed, sofa rug, or other soft surface. Doing so may block the ventilation openings in the
bottom of the cabinet. If you put the LCD monitor in a bookcase or some other enclosed
space, be sure to provide adequate ventilation.
2. Put your LCD monitor in a location with low humidity and a minimum of dust.
3. Do not expose the LCD monitor to rain or use it near water (in kitchens, near swimming
pools, etc.). If the LCD monitor accidentally gets wet, unplug it and contact an authorized
dealer immediately. You can clean the LCD monitor with a damp cloth if necessary, but be
sure to unplug the LCD monitor rst.
4. Place your LCD monitor on a solid surface and treat it carefully.
5. Locate your LCD monitor near an easily accessible AC outlet.
6. High temperature can cause problems. Don't use your LCD monitor in direct sunlight and
keep it away from heaters, stoves, replaces, and other sources of heat.
On Cleaning
The screen is made of thin glass with a plastic front surface and can be damaged if dropped,
hit or scratched. Do not clean the front panel with keton-type materials (e.g., acetone), ethyl
alcohol, toluene, ethyl acid, methyl, or chloride - these may damage the panel.
Panel : Clean with a soft woolen or cotton towel. Use a watery solution or a mild commercial
glass cleaning solution.
Cabinet : Clean with a soft cloth dampened with mild detergent and water. Repeat this with
water only and wipe dry with a dry cloth.
On Repacking
Do not throw away the carton and packing materials. They make an ideal container which to
transfer the unit. If you have any questions about this unit, contact your authorized dealer.
On Disposal
The lamps inside the display contain mercury which can pollute the environment if disposed
carelessly. Please contact our nearest representative ofce or your local environmental ofce
in case of disposal of this unit.
Contact
WIDE Corporation
456, Gomae-dong, Giheung-gu, Yongin-si, Gyeonggi-do, 446-901, Korea
(TEL : +82-31-218-1600 / FAX : +82-31-274-7400) / http://www.widecorp.com
6
Your New LCD Monitor
When you unpack the LCD Monitor, make sure that you have items below.
Manual Monitor Warranty Card
(not available all Iocations)
Power Card DVI Signal Cable 15-Pin D-Sub Signal Cable
Component Video cable S-Video cable
BNC cable USB-Cable 5pin BNC cable (Option)
USB-Driver OPTIC MODULE (Option)
▶ Abovepicturesmaydifferfromtherealone.
7
Regulatory Information
FCC Information
User Instructions
The Federal Communications Commission Radio Frequency Interference Statement includes
the following warning:
NOTE
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television receptions, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
User Information
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
If necessary, consult your dealer or an experienced radio/television technician for additional
suggestions. You may find the booklet called How to Identify and Resolve Radio/TV
Interference Problems helpful. This booklet was prepared by the Federal Communications
Commission. It is available from the U.S. Government Printing Ofce, Washington, DC 20402,
Stock Number 004-000-00345-4.
Warning User must use shielded signal interface cables to maintain FCC compliance for the
product.
•
•
•
•
8
Regulatory Information
Declaration of conformity for products Marked with FCC Logo
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
The party responsible for product compliance:
Provided with this monitor is a detachable power supply cord with IEC320 style terminations. It
may be suitable for connection to any UL Listed personal computer with similar conguration.
Before making the connection, make sure the voltage rating of the computer convenience
outlet is the same as the monitor and that the ampere rating of the computer convenience
outlet is equal to or exceeds the monitor voltage rating.
For 120 Volt applications, use only UL Listed detachable power cord with NEMA conguration
5-15P type (parallel blades) plug cap. For 240 Volt applications use only UL Listed Detachable
power supply cord with NEMA conguration 6-15P type (tandem blades) plug cap.
IC Compliance Notice
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations of ICES-003.
VCCI Class B ITE
この装置は、情報処理装置等電波障害自主規制協議会（ＶＣＣＩ）の基準に基づくクラ
スB 情報技術装置です。この装置は、家庭環境で使用することを目的としていますが、こ
の装置がラジオやテレビジョン受信機に近接して使用されると、受信障害を引き起こすこ
とがあります。
取扱説明書に従って正しい取り扱いをして下さい。
9
Connecting your LCD Monitor
Rear bottom view
CVBS
AC INPUT RS232 DIGITAL ANALOG BNC/COMPONENT SOG-OUT HD-SDI S-VIDEO USBSWITCH
IN
H V
OUT
IN
OUT
IN OUT
R/Pr G/Y B/Pb
DOWN
(OPTION)
UP
Connecting power cord
Connect the power cord to the AC input outlet on the back of the monitor,turn the power switch
on.
Do not turn the power switch on before you have nished the connection.
Caution
Connecting the computer
1. RGB cable connection (Fig.1) : Connect the RGB cable included to the D-Sub input port
on the back of the monitor.
Press the source selection button to select PC.
2. DVI cable connection (Fig.2) : Connect the DVI cable included to the DVI input port on
the back of the monitor.
Press the source selection button to select DVI.
You may not have a picture if video card is not suitable.
(Fig.2)
(Fig.1)
DVI cable
RGB cable
CVBS
AC INPUT RS232 DIGITAL ANALOG BNC/COMPONENT SOG-OUT HD-SDI S-VIDEO USBSWITCH
IN
H V
OUT
IN
OUT
IN OUT
R/Pr G/Y B/Pb
DOWN
(OPTION)
UP
Loading...