Wholesale Interiors FREDAGREYVELVETDAYBEDQT, FREDAGREYVELVETDAYBEDFT, FREDALIGHTBLUEVELVETDAYBEDQT, FREDALIGHTBLUEVELVETDAYBEDFT Assembly Guide
FREDA DAYBED-F/T
FREDA DAYBED-Q/T
NO PART LIST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
ITEM
A
B
C
D
E
F
G
H
I
J
K
SIDE PANEL
SIDE PANEL
7pcs
FRONT RAIL
5pcs
HARDWARE
JCBB SCREW
JCBC SCREW
JCBC SCREW
SPRING WASHER
FLAT WASHER
(BIG)
FLAT WASHER
(SMALL)
BACK REST
(L)
(R)
FRONT
SIDE RAIL
BACK
SIDE RAIL
LEG
SLAT
CENTER
SUPPORT
SUPPORT
LEG
TRUNDLE
TRUNDLE
BACK RAIL
TRUNDLE
SIDE RAIL
SLAT
SLAT
SUPPORT
CASTOR
M8 x 20MM
M6 x 40MM
M6 x 50MM
SCREW
M4 x 16MM
SCREW
M4 x 32MM
L - KEY
M4 x 100MM
L - KEY
M5 x 65MM
STOPPER
QTY
1PC
1PC
1PC
1PC
1PC
4PCS
2 SET
1PC
2PCS
1PC
1PC
2PCS
2 SET
3PCS
6PCS
QTY
20PCS
4PCS
16PCS
16PCS
4PCS
12PCS
24PCS
22PCS
1PC
1PC
2PCS
STEP 1
Begin assembly by attaching each Leg (6) to the bottom of the
Side Panel (2) & (3) securing with 2 Allen Bolt (C) per panel using
L-key (I).
2
6
C
3
I
STEP 3
Attach the Back Rest (1) to each Side Panel (2) & (3) by aligning the
hole and securing with 2 Allen Bolts (B), 2 Spring Washer (D), 2 Flat
Washer (E) per each end using L-key (I) as picture below.
(DO NOT FULLY TIGHTEN BOLTS FOR THIS STEP)
1
3
1
2
B
D
E
4
3
STEP 2
Attach the Front Rail (4) and Back Rail (5) to the Side Panel (2) & (3)
by aligning holes and securing with 2 Allen Bolts (A) per each end using
L-key (J). (DO NOT FULLY TIGHTEN BOLTS FOR THIS STEP)
2
A
5
4
3
STEP 4
Secure 2 Support Leg (9) to the Center Support (8) as shown on step 4.1.
Tighten the Support Leg (9) clockwise until secure. Insert the pre-set
metal on Center Support (8) to the metal bracket on each side of Side
Panel (2) & (3) as step 4.2. Then securing the metal bracket as shown in
step 4.3 with 1 Screw (H) each side using Phillips Head Screwdriver
(NOT INCLUDED)
8
STEP 4.2
I
STEP 4.3
2
H
4
STEP 4.1
8
3
8
9
1
J
Please do not tighten the hardware until the entire assembly is completed.
STEP 5 STEP 6
Tighten All Bolts from step 1 to step 4 by using L-key (I) & (J) that has been provided.
Attached Slat (7) to Front Side Rail (4) & Back Side Rail (5) by unrolling and securing
with 6 Screw (H), per set using Phillips Head Screwdriver. Securing Slat (7) to Back Side
Rail (5) with 2 Screw (H) as step 5.1. Following by step 5.2, using 1 Screw (F) to secure
Slat (7) to Front Side Rail (4). Repeat the same step to attach another set of Slat (7).
STEP 5.1
H
Attach the Stopper (K) to the front side of Side Panel (2) & (3) each side by
securing with 2 Allen Bolt (A) using L-key (J) to avoid trundle pull out.
2
STEP 5.2
7
4
A
K
J
3
STEP 7
7
4
H
7
5
Please do not tighten the hardware until the entire assembly is completed.
ASSEMBLY
COMPLETE
Loading...