Wholesale Interiors FREDAGREYVELVETDAYBEDFULL, FREDAGREYVELVETDAYBEDQUEEN, FREDALIGHTBLUEVELVETDAYBEDQUEEN, FREDALIGHTBLUEVELVETDAYBEDFULL Assembly Guide
FREDA DAYBED-F/FREDA DAYBED-Q
NO PART LIST
1
2
3
4
5
6
7
8
9
ITEM
A
B
C
D
E
F
G
H
BACK REST
SIDE PANEL
SIDE PANEL
FRONT
SIDE RAIL
BACK
SIDE RAIL
7pcs
CENTER
SUPPORT
SUPPORT
LEG
HARDWARE
JCBB SCREW
M8 x 20MM
JCBC SCREW
M6 x 40MM
JCBC SCREW
M6 x 50MM
SPRING WASHER
FLAT WASHER
M4 x 32MM
L - KEY
M4 x 65MM
M5 x 65MM
(L)
(R)
LEG
SLAT
SCREW
L - KEY
QTY
1PC
1PC
1PC
1PC
1PC
4PCS
2 SET
1PC
2PCS
QTY
12PCS
4PCS
4PCS
4PCS
4PCS
14PCS
1PC
1PC
STEP 1
Begin assembly by attaching each Leg (6) to the
bottom of the Side Panel (2) & (3) securing with
2 Allen Bolt (C) per panel using L-key (G).
Then attach the Back Side Rail (5) to the Side Panel
(2) & (3) by aligning holes and securing with 2
Allen Bolts (A) per each side using L-key (H).
And attach the Front Side Rail (4) also by aligning
holes and securing with 4 Allen Bolts (A) per
side using L-key (H).
(DO NOT FULLY TIGHTEN BOLTS FOR THIS STEP)
STEP 1.1
6
C
STEP 2
Attach the Back Rest (1) to each Side Panel (2) & (3) by aligning
the hole and securing with 2 Allen Bolts (B), 2 Spring Washer (D),
2 Flat Washer (E) as picture below per each end
using L-key (G).
(DO NOT FULLY TIGHTEN BOLTS FOR THIS STEP)
2
STEP 1.2
A
H
2
5
4
3
G
1
3
1
B
D
E
G
5
Please do not tighten the hardware until the entire assembly is completed.
4
3
STEP 3 STEP 4
Secure 2 Support Leg (9) to the Center Support (8) as shown on step 3.1. Tighten the
Support Leg (9) clockwise until secure. Insert the pre-set metal on Center Support (8) to the
metal bracket on each side of Side Panel (2) & (3) as step 3.2. Then securing the metal
bracket as shown in step 3.3 with 1 Screw (F) each side using
Phillips Head Screwdriver (NOT INCLUDED)
8
STEP 3.1
8
Tighten All Bolts from step 1 to step 3 by using L-key (G) & (H) that has been provided.
Attached slat (7) to Front Side Rail (4) & Back Side Rail (5) by unrolling and securing
with 6 Screw (F) per set. Securing Slat (7) to Back Side Rail (5) with 2 Screw (F) as step
4.1. Following by step 4.2, using 1 Screw (F) to secure Slat (7) to Front Side Rail (4).
Repeat the same step to attach another set of slat (7).
STEP 3.2
STEP 3.3
STEP 5
9
2
8
3
F
7
4
STEP 4.1
F
7
5
STEP 4.2
F
ASSEMBLY
COMPLETE
Please do not tighten the hardware until the entire assembly is completed.
7
Loading...