Wholesale Interiors ABBIEGREYVELVETDAYBEDFT, ABBIEGREYVELVETDAYBEDQT, ABBIELIGHTBLUEVELVETDAYBEDFT, ABBIELIGHTBLUEVELVETDAYBEDQT Assembly Guide
ABBIE DAYBED-F/T
ABBIE DAYBED-Q/T
NO PART LIST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
ITEM
A
B
C
D
E
F
G
H
I
J
SIDE PANEL
SIDE PANEL
7pcs
FRONT RAIL
5pcs
HARDWARE
JCBB SCREW
JCBC SCREW
SPRING WASHER
FLAT WASHER
(BIG)
FLAT WASHER
(SMALL)
BACK REST
(L)
(R)
FRONT
SIDE RAIL
BACK
SIDE RAIL
LEG
SLAT
SLAT
SUPPORT
SUPPORT
LEG
TRUNDLE
TRUNDLE
BACK RAIL
TRUNDLE
SIDE RAIL
SLAT
SLAT
SUPPORT
CASTOR
M8 x 20MM
M6 x 50MM
SCREW
M4 x 16MM
SCREW
M4 x 32MM
L - KEY
M4 x 100MM
L - KEY
M5 x 65MM
STOPPER
QTY
1PC
1PC
1PC
1PC
1PC
4PCS
2 SET
1PC
2PCS
1PC
1PC
2PCS
2 SET
3PCS
6PCS
QTY
20PCS
20PCS
16PCS
4PCS
12PCS
24PCS
22PCS
1PC
1PC
2PCS
STEP 1
Begin assembly by attaching each Leg (6) to the bottom of the
Side Panel (2) & (3) securing with 2 Allen Bolt (B) per panel using
L-key (H).
2
6
B
H
3
STEP 3
Attach the Back Rest (1) to the back of each Side Panel (2) & (3) by
aligning the hole and securing with 2 Allen Bolts (B), 2 Spring Washer
(C), 2 Flat Washer (D) from the back side per each end using L-key (H).
(DO NOT FULLY TIGHTEN BOLTS FOR THIS STEP)
1
H
1
2
3
4
B
D
C
STEP 2
Attach the Front Rail (4) and Back Rail (5) to the Side Panel (2) & (3)
aligning holes and securing with 2 Allen Bolts (A) per each end using
L-key (I). (DO NOT FULLY TIGHTEN BOLTS FOR THIS STEP)
A
2
I
5
3
4
STEP 4
Secure 2 Support Leg (9) to the Slat Support (8) as shown on step 4.1.
Insert the pre-set metal on Slat Support (8) to the metal bracket on each
side of Side Panel (2) & (3). Then securing the metal bracket as shown
in step 4.3 with 1 Screw (G) each side using Phillips Head Screwdriver
(NOT INCLUDED)
STEP 4.1
8
STEP 4.2
2
STEP 4.3
4
G
8
9
1
8
3
Please do not tighten the hardware until the entire assembly is completed.
STEP 5 STEP 6
Tighten All Bolts from step 1 to step 4 by using L-key (I) & (J) that has been provided.
Attached Slat (7) to Front Side Rail (4) & Back Side Rail (5) by unrolling and securing
with 6 Screw (G), per set using Phillips Head Screwdriver. Securing Slat (7) to Back Side
Rail (5) with 2 Screw (G) per each side as step 5.1. Following by step 5.2, using 1 Screw
(G) to secure Slat (7) to Front Side Rail (4).
Repeat the same step to attach another set of Slat (7).
STEP 5.1
G
Attach the Stopper (J) to the front side of Side Panel (2) & (3) each side by
securing with 2 Allen Bolt (A) using L-key (I) to avoid trundle pull out.
2
3
STEP 5.2
7
5
7
4
G
7
STEP 7
4
A
J
I
Please do not tighten the hardware until the entire assembly is completed.
Loading...