White-Westinghouse WM40T User Manual
LAVABIANCHERIA
MANUALE DELL’UTENTE
WASHING MACHINE
USER MANUAL
mode d’emploi de machine
à laver électronique
THE CONTENTS
SECTION 1:BEFORE USING
• Safety warnings
• Recommendations
SECTION 2:INSTALLATION
• Removal of transportation screws
• Adjustment of feet
• Electrical connection
• Water supply connection
• Water drain connection
SECTION 3:TECHNICAL SPECIFICATIONS
SECTION 4:CONTROL PANEL
• Start/Pause button
• Function indicator lights
• Function buttons
• Spin speed selector
• Program knob
SECTION 5:WASHING YOUR LAUNDRY
• Before washing
• Running the machine
SECTION 6:MAINTENANCE AND CLEANING
• Water inlet filters
• Pump filter
• Detergent drawer
• Siphon plug
• The cabinet
• The drum
• Remove of your machine from lime
SECTION 7: PRACTICAL INFORMATION
SECTION 8:AVOIDING MINOR FAULTS
SECTION 9:AUTOMATIC FAILURE DETECTION SYSTEM
SECTION 10:INTERNATIONAL WASHING SIGNS
28
SECTION 1:BEFORE USING
SAFETY WARNINGS
•
• Do not use a multiple socket or extension cord.
••
• Do not insert a plug with damaged or broken cord into the socket.
• If the cord is damaged it should be replaced by the manufacturer or
appointed service agent in order to avoid a hazard.
•
• Never remove the plug from the socket by pulling from the cord
••
section. Remove the plug by holding.
•
• Do not plug the power supply with wet hands.
••
•
• Never touch the machine with wet hands or feet.
••
•
• Never open the detergent drawer while the device is running.
••
•
• Never force to open the door of the machine while the machine is
••
running.
•
• Since the machine can reach high temperatures while running, do not
••
touch the drain hose and water during draining.
•
• In case of any failure, first unplug the device and close the water tap.
••
Do not attempt to repair.Please apply to the nearest authorized
service station.
•
• Do not forget that the packing material of your machine may be
••
hazardous for children.
•
• Do not let your children play with the washing machine.
••
•
• Keep your pet away from your machine.
••
•
• Your machine should only be used by adults within the information
••
written in this manual.
•
• Your machine is designed for use in house environment. Warranty
••
will be invalid if you use it for commercial purposes.
RECOMMENDATIONS
•
• The detergent or softener in contact with air for a long time will dry
••
and stick to your detergent drawer.To avoid this put your detergent
and softener into the detergent drawer just before washing.
•
• It is recommended that you use pre-washing program for only very
••
dirty clothes.
•
• Please do not exceed the maximum loading capacity.
••
29
•
• If you will not use your machine for a long time, unplug your machine,
••
close the water supply and leave the door open in order to keep the
inside of the machine dry and for prevention from unpleasant odour.
•
• As a result of the quality control procedures, a certain amount of
••
water may remain in your machine. This is not harmful for your
machine.
SECTION 2: INSTALLATION
You must pay attention to the following issues before using your washing
machine.
REMOVAL OF TRANSPORTATION SCREWS
•
• Transportation screws, which are located at the back side of the
••
machine, must be removed before running the machine.
•
• Loosen the screws by rotating counterclockwise by a suitable wrench.
••
(DIAGRAM-1)
•
• Remove the screws by pulling them.(DIAGRAM-2)
••
•
• The plastic parts located in the interior part of your machine will fall
••
down under the device.
•
• Lift your machine up slightly, pick up the plastic parts.
••
•
• If all of the plastic parts of screw groups have not fallen down; open
••
the door of your machine,move the drum until all plastic parts fall
down. Collect the parts that have fallen to the floor.
•
• To the holes where the transport screws have been removed, insert
••
the plastic transport screw taps found in the accessories bag.
(DIAGRAM-3)
•
• The transportation screws, that have been removed from the machine
••
should be kept in hand for any other transportation necessities.
DIAGRAM-2
DIAGRAM-1 DIAGRAM-3
ADJUSTMENT OF FEET
•
• Do not install your machine on rugs or similar surfaces.
••
•
• For your machine to work silently and without any vibration, it should
••
be settled on a flat, non-slippery and tough ground.
30
•
• You can adjust the balance of your machine from its feet.
••
•
• First, loosen the plastic adjustment nut.
••
•
• Adjust by rotating the feet upwards or downwards.
••
•
• After the balance has been reached, tighten the plastic adjustment
••
nut again by rotating it upwards.
•
• Never put cartons, wooden blocks or similar materials under the
••
machine to balance the irregularities on the level of the ground.
ELECTRICAL CONNECTION
•
• Your washing machine works with 220-240V and 50Hz.
••
•
• A special grounded plug has been attached to the network cable of
••
your washing machine. This plug must definitely be inserted to a
grounded socket with 10 ampere. The fuse flow value of the
electricity line attached to this should also be 10 ampere. If you have
no such sockets and fuses in your house, let it be made by a qualified
electrician.
• Our company will not be responsible for any damages that may
occur as a result of usage without grounding.
WATER SUPPLY CONNECTION
• Your machine has a single water (cold) inlet.
• To prevent from the leakages on the connection joints, 1 seal is
included in the hose packing.(Fit this seal on the end of the water
inlet hose at the tap side.)
• Connect the end with bracket of the water inlet hose to the water inlet
valve at the rear of the machine and the other end to your tap. In
situations where you are not assured, let a qualified plumber make
the connection works.
• Water pressure of 1-10 bars from your tap will enable your machine
to work more efficiently.(1 bar pressure means water flow of more
than 8 liters in 1 minute from a fully opened tap).
• After connections are completed, check for the non-leakage of the
connection joints by turning on your tap completely.
• Be sure that water inlet hoses are not folded, broken or crushed.
• Mount the water inlet hoses to a 3”/4, geared water tap.
WATER DRAIN CONNECTION
• Be sure that water inlet hoses are not folded, twisted, crushed or
elongated by stretching.
• Water drain hose should be mounted at a height of minimum 60 cm,
maximum 100 cm from the ground.
• The end of the water drain hose may directly be fitted to the dirty
water outlet hole or a special apparatus mounted on the outlet
bracket of the wash-stand.
• Never attempt to extend the water drain hose by adding extra parts.
Cold water inlet
32
SECTION 3:TECHNICAL SPECIFICATIONS
WM40T-1
Maximum dry laundry capacity (kg) 5
Recommended loading (kg) 4,5
Height (cm) 85
Width (cm) 59,6
Depth (cm) 51
Maximum spin cycle ( rpm ) 400
(*) Maximum spin cycles depend on the model you’ve chosen
1 2 3
4
5
6
7
1-Upper tray 5-Handle
2-Detergent drawer 6-Filter cover
3-Control panel 7-Kickplate
4-Door
33
SECTION 4:CONTROL PANEL
WM40T-1
1 2 3 4 5 6
7 8 9
1-Detergent drawer 6-Program knob
2-Start/pause light 7-Start/pause button
3-Function indicator lights 8-Function buttons
4-Temperature adjustment knob 9-Program end light
5-Program ready light
34
START/PAUSE BUTTON
Used to start a selected program or pause during running.
It is required for the program knob to be brought to O(off)
position before selecting the program or changing a continuing
program.
WARNING!
FUNCTION INDICATOR LIGHTS
When the start/pause button or any function button is pressed,the
corresponding light turns on.The light turns off when the function
button or start/pause button is re-pressed, or when the process
the selected function is completed.
The function indicator lights are also used in failure detection system
mentioned in section 9.
FUNCTION BUTTONS
No spin
This program is recommended to be used for your sensitive
clothes on which no spinning should be done. By pressing this
function button, you can cancel the spinning process which is
included in the program.
Easy ironing
By using this function, you can ensure your clothes to come out
less wrinkled after the washing.
35
Loading...