White-Westinghouse 218954301 User Manual

P/N 218954301 (0009)

Product Registration

The information contained within this Owner's Guide will instruct you on how to
properly operate and care for your product. Please read through the information
contained in your literature pack to learn more about your new appliance.

Record Your Model and Serial Numbers

Record the Model Number and Serial Number of this refrigerator in the space
provided below. These numbers are found on the serial plate located on the ceiling
of the refrigerator compartment.

Model Number: __________________________________________________
Serial Number: ___________________________________________________

Register Your Product

The self-addressed PRODUCT REGISTRATION CARD should be filled in completely,
signed and returned to the Frigidaire Company, or, in Canada, Frigidaire Canada.

Contents

This Owner’s Guide provides specific
operating instructions for your model.
Use the refrigerator only as instructed in
this Owner’s Guide.

2 Product Registration
3 Important Safety Instructions

3 For Your Safety
3 Child Safety
3 Electrical Information
3 Other Precautions

4- 5 First Steps

4 Location
4 Installation
4 Door Opening
4 Leveling
4 Cleaning
5 Connecting Ice Maker to Water Supply

6 Energy Saving Ideas
6 Setting the Controls

6 Cool Down Period
6 Refrigerator Control
6 Freezer Control

7 Fresh Food Storage
8-10 Automatic Ice and Water Dispenser

8 Light
8 How the Water Dispenser Works
8 How the Ice Dispenser Works
9 Ice Dispenser Tips
9 Cleaning the Ice Dispenser
10-11 Ice & Water Filter (some models)

12-13 Care and Cleaning

12 Inside
12 Outside
1 2 Replacing the Light Bulb
1 3 Vacation and Moving Tips

13-14 Removing the Handles and Doors

13 To Remove Handles
1 4 To Remove Freezer Door
1 4 To Remove Refrigerator Door
1 4 To Reinstall Freezer Door
1 4 To Reinstall Refrigerator Door

15-18 Avoid Service Checklist
1 8 Normal Operating Sounds
19 Warranty

© 2000 White Consolidated Industries, Inc.

All rights reserved.

2

Important Safety
Instructions

Proper Disposal of Your
Refrigerator/Freezer

Read all instructions before using this refrigerator.

For Your Safety

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of
this or any other appliance. Read product labels for flammability and other warnings.

Risk of child entrapment.
Child entrapment and suffocation are
not problems of the past. Junked or
abandoned refrigerators are still
dangerous - even if they will sit for
"just a few days." If you are getting rid
of your old refrigerator, please follow
instructions below to help prevent
accidents.
BEFORE YOU THROW
AWAY YOUR OLD
REFRIGERATOR OR
FREEZER:

• Take off doors.

• Leave shelves in

place, so children
may not easily
climb inside.

Avoid fire hazard or
electric shock. Do not use an extension
cord or an adapter plug. Do not remove
any prong from the power cord.

Child Safety

• Destroy carton, plastic bags, and any exterior wrapping material immediately
after the refrigerator is unpacked. Children should never use these items for
play. Cartons covered with rugs, bedspreads, plastic sheets or stretch wrap
may become airtight chambers and can quickly cause suffocation.

• Remove all staples from the carton. Staples can cause severe cuts and destroy
finishes if they come in contact with other appliances or furniture.

• An empty, discarded ice box, refrigerator or freezer is a very dangerous
attraction to children. Remove the door of any appliance that is not in use,
even if it is being discarded.

Electrical Information

These guidelines must be followed to ensure that safety mechanisms in
the design of this refrigerator will operate properly.

• The refrigerator must be plugged into its own 115 Volt, 60 Hz, AC only
electrical outlet. The power cord of the appliance is equipped with a three-

prong grounding plug for your protection against shock hazards. It must be
plugged directly into a properly grounded three-prong receptacle. The recep­tacle must be installed in accordance with local codes and ordinances. Consult
a qualified electrician.

• If voltage varies by 10 percent or more, performance of your refrigerator may
be affected. Operating the refrigerator with insufficient power can damage
the compressor. Such damage is not covered under your warranty. If you
suspect your voltage is high or low, consult your power company for testing.

• To prevent the refrigerator from being turned off accidentally, do not plug
the unit into an outlet controlled by a wall switch or pull cord. Do Not Use

An Extension Cord Or An Adapter Plug.

• Do not pinch, knot, or bend the power cord in any manner.

Other Precautions

• Never unplug the refrigerator by pulling on the power cord. Always grip the
plug firmly and pull straight out from the receptacle.

• To avoid electrical shock, unplug the refrigerator before cleaning and before
replacing a light bulb. NOTE: Turning the control to OFF turns off the
compressor, but does not disconnect power to the light bulb or other electrical
components.

• Do not operate the refrigerator in the presence of explosive fumes.

• If the refrigerator has an automatic ice maker, avoid contact with any moving
parts.

3

First Steps

Before starting the refrigerator, follow these important first steps:

Location

• Choose a place that is near a grounded electrical outlet. DO NOT use an

extension cord or an adapter plug.

• If possible, place the refrigerator out of direct sunlight and away from the

range, dishwasher or other heat sources.

• The refrigerator must be installed on a floor that is level and strong enough to

support a fully loaded refrigerator.

• Consider water supply availability for the automatic ice maker.

Installation

• Do not install the refrigerator where the temperature will drop below 60°F

(15°C) or rise above 110°F (43°C). The compressor will not be able to
maintain proper temperatures.

• In a recessed installation, allow an extra 1/2 inch (10-15 mm) on each side for

ease of installation.

• If the hinge side of the unit will be placed against a wall, allow a 1 3/4 inch

(44 mm) space between the wall and the refrigerator to permit proper door
swing.

Door Opening

For best use of the drawers and freezer basket, the refrigerator should be in a
position where both the refrigerator and freezer doors can be opened about 135°.

Replacing Toe Grille

Leveling

• The refrigerator must be leveled with all bottom corners resting firmly on a

solid floor. Adjust front rollers to level cabinet both front-to-rear and
side-to-side. Keep the cabinet as low as possible for stability. Never adjust

cabinet rollers so the front is lower than the rear.

• To adjust the front rollers: Open the refrigerator and freezer doors. Remove

the toe grille by pulling it straight out. Adjust the rollers by turning each
rolleradjusting bolt with an adjustable wrench, a socket wrench or a nutdriver
until the refrigerator is level and stable. The rear rollers are not adjustable.

• Check both doors to be sure seals touch cabinet evenly on all four sides.

• If the freezer door is higher than the refrigerator door, raise the right corner

and/or lower the left corner until the doors align across the top of the cabinet.

• If the refrigerator door is higher than the freezer door, raise the left corner

and/or lower the right corner until the doors align across the top of the cabinet.

• To replace the toe grille: Line up clips with holes and push grille straight on.

Cleaning

• Wash the inside, all removable parts and the outside with mild detergent and

warm water. Wipe dry. Do Not Use Harsh Cleaners On These Surfaces.

• Do not use razor blades or other sharp instruments which can scratch the

appliance surface, when removing adhesive labels. Any glue left from the
tape or energy label can be removed with a mixture of warm water and mild
detergent, or, touch the residue with the sticky side of tape already removed.

• Do Not Remove The Serial Plate.

4

First Steps

(continued)

Figure 2

Figure 1

Connecting Ice Maker to Water Supply

Do Not Install Ice Maker Tubing Wher e T emperature May Fall

Below Freezing.

Check to be sure your water connection will comply with local plumbing codes.
Water quality determines your ice quality. It is best to connect the ice maker to

water that is not softened. Chemicals from a malfunctioning softener can damage
the ice maker . If the ice maker is connected to soft water , ensure that the softener
is maintained and working properly .

The ice maker requires a 1/4 inch (6.4 mm) copper water supply line (with shutoff)
from your household water system. Allow enough tubing behind your refrigerator
to permit moving out to clean floor .

A water line kit is available through your dealer at extra charge. This kit includes 1/
4 inch diameter copper tubing, plus parts to connect to your cold water line. Y ou
will need to purchase a 1/4 inch brass compression nut and ferrule from your local
hardware or plumbing store.

1. Turn ON water supply and flush out copper tubing. Turn off water supply .

2. Unplug refrigerator.

3. Install WATER SUPPL Y LINE as follows (figure 2):

• Slide brass nut, then ferrule, onto copper tubing.

• Push end of copper tubing as far into the metal water valve fitting as
it will go (1/4 inch). Slide ferrule into fitting and thread brass nut onto
inlet, tighten finger tight plus 1/2 turn with wrench.

NOTE: Some models may have a cap on the valve. Unscrew the cap and
discard.

4. Secure copper tubing with STEEL CLAMP and screw to rear panel at
location shown (Figure 3).

5. Coil water supply tubing as shown (figure 3).
NOTE: T o prevent vibration noise and wear , leave a space between all

tubing and other surfaces.

6. T urn on water supply and check all connections for leaks (figure 3).

7. Plug refrigerator cord into wall outlet.

8. To begin ice production, lower the Wire Signal Arm to the “down” or “ON”
position (Figure 4).

Figure 3

Figure 4

IMPORT ANT

Ice production will begin when freezer reaches normal operating temperature. Air
in new plumbing lines may cause ice maker to cycle two or three times before
making a full tray of ice.

New plumbing may cause ice to be discolored or have poor flavor. Discard ice
made during the first 24 hours. After installation, if you wish to shut the ice maker
off, lift the Wire Signal Arm until it clicks and locks in the “UP” position.

5

Energy Saving
Ideas

• Locate the refrigerator in the coolest part of the room, out of direct sunlight
and away from heating ducts or registers. Do not place the refrigerator next
to heat-producing appliances such as a range, oven or dishwasher. If this is
not possible, a section of cabinetry or an added layer of insulation between
the two appliances will help the refrigerator operate more efficiently.

• Level the refrigerator so the doors close tightly.

• Refer to this Owner's Guide for the suggested refrigerator settings.

• Periodic cleaning of the condenser will help the refrigerator run more
efficiently. See Outside in the "Care and Cleaning" section.

• Do not overcrowd the refrigerator or block cold air vents. Doing so causes
the refrigerator to run longer and use more energy. Shelves should not be
lined with aluminum foil, wax paper or paper toweling. Liners interfere with
cold air circulation, making the refrigerator less efficient, which could cause
food spoilage.

• Cover foods and wipe containers dry before placing them in the refrigerator.
This cuts down on moisture build-up inside the unit.

• Organize the refrigerator to reduce door openings. Remove as many items
as needed at one time and close the door as soon as possible.

Setting the Controls

Refrigerator Control

Cool Down Period

To ensure safe food storage, allow the refrigerator to operate with the doors closed
for at least 8 to 12 hours before loading with food.

Refrigerator Control

• The refrigerator control should be set at the midpoint of the dial for a trial period

of 24 hours.

• After 24 hours, adjust the control as needed. For colder temperatures, turn the

dial a notch toward COLDEST. For warmer temperatures, turn the dial a notch
toward COLD. Adjust temperatures by one increment at a time.

Freezer Control

• The freezer control should be set at the midpoint of the dial for a trial period of

24 hours.

• After 24 hours, adjust the control as needed. For colder temperatures, turn the

dial a notch toward COLDEST. For warmer temperatures, turn the dial a notch
toward COLD. Adjust temperatures by one increment at a time.

NOTE: When first setting the controls or when changing a setting, wait 24 hours for
the temperature to stabilize before making additional changes.

Turning the freezer control may change temperatures in both compartments. For
example, if the freezer control is turned to a colder setting, the refrigerator control
may have to be adjusted to a warmer one. Turning the refrigerator control will
change only the refrigerator temperature.

Freezer Control

IMPORTANT: If the freezer control is turned to OFF, cooling stops in both
compartments.

You may hear the "Frost Free" system working. A fan circulates air in the
refrigerator and freezer compartments. For good circulation and maintenance of
proper cooling temperatures, do not block cold air vents with food items. Water
draining into the defrost water pan and hissing sounds are normal during the
automatic "Frost Free" cycle.

6

Fresh Food
Storage

Shelf Adjustment

Refrigerator shelves are easily adjusted to suit individual needs. Before adjusting
shelves, remove all food. The shipping clips which stabilize the shelves for shipping
may be removed and discarded.

LIP
ALLY

Remove shipping clips

To adjust the cantilever shelves (shelves supported at the rear of the refrigerator),
lift the back of the shelf up and out. Replace shelf by inserting hooks at rear into
slots. Lower and lock into position.

Door Storage

Door bins and shelves are provided for convenient storage of jars, bottles and cans.
Items used often are available for quick selection.

The door bins can be moved to suit individual needs. Remove bins by lifting straight
up. Place bins in the desired position and lower over the supports.

The Dairy compartment is warmer than the general food storage section and is
intended for short term storage of cheese, spreads, or butter.

Crisper

The Crisper drawer, located under the bottom refrigerator shelf, is for storing fruits
and vegetables. Most produce should be washed in clear water and drained before
placing in this drawer. Items with strong odors or high moisture should be wrapped
before storing.

Meat Keeper

The Meat Keeper is located at the bottom of the refrigerator. The temperature in
this compartment can be made colder than the rest of the refrigerator compart­ment by sliding the Chilled Air Control knob within the COLDEST or COLD range.
Meat will be partially frozen and may be kept fresh longer than if stored on a
refrigerator shelf.

Chilled Air Control

Before placing items in the Meat Keeper, follow these steps to keep the meat fresh:

1. Carefully handle meat with clean hands and always keep the compartment
clean.

2. Store meat in its original wrapper. If necessary, overwrap in plastic wrap or foil
to prevent drying. Wrap fish tightly to prevent odor transfer to other foods.

3. If spoilage ever occurs, disinfect the compartment with liquid chlorine bleach
following label directions. Then rinse with a solution of baking soda and water.
Rinse with clear water and dry.

Freezer Basket (some models)

Some models are equipped with a slide-out wire basket below the bottom freezer
shelf. This basket provides easy access to frozen food packages.

7

Automatic Ice and
Water Dispenser

The ice and water dispenser on the freezer door conveniently dispenses chilled
water, and ice cubes (some models). To operate the dispenser, slide the knob to
the selection of your choice and press a glass against the dispensing bar, as shown.
Be sure to hold the glass as far up as possible to catch all cubes. To stop dispensing,
pull glass away from dispensing bar. When dispensing ice, release the dispensing
bar before the glass is full, but do not remove the glass until the ice has completely
dispensed. When dispensing ice, release the dispensing arm before the glass is full,
but do not remove the glass until the ice has completely dispensed.

A small heated area beneath the dispenser floor catches and evaporates small spills.
Do not pour water or excess cubes into this area because there is no drain.

Dispenser Selector

Press glass against dispensing bar.

Light

The dispenser has a light which can be turned on and off by sliding the knob to the
desired position. The light also turns on automatically when ice and/or water is
dispensed. Replace light bulb with an appliance bulb of the same wattage.

How the Water Dispenser Works

The water tank is located behind the drawers in the refrigerator compartment and
holds about 48 ounces (1.5 liters) of water. As the water is dispensed, the tank is
automatically refilled. For proper operation of the dispenser, the supply water
pressure must fall between 30 psi and 120 psi.

After the refrigerator is installed and the plumbing connections are complete, the
water tank should be filled by drawing one glass of water. This will take about
1½ minutes. Then, draw and discard 7 more glasses to be sure that the tank and
plumbing connections are rinsed of any impurities.

To ensure fresh-tasting water, plan to use the dispenser every day. If the water
dispenser has not been used for a week or more, draw and discard 7-8 glasses to
freshen the tank supply.

How the Ice Dispenser Works

The ice maker and ice storage bin are located in the top left corner of the freezer
compartment. After the refrigerator is installed properly and has cooled for several
hours, the ice maker can begin making ice. To begin ice production, lower the wire
signal arm to the "down" or ON position. As cubes are made, they are stored in
the storage bin. Although it may take 1 or 2 days to fill the bin, the dispenser may
be used after the first batch of ice is made. The ice maker turns off automatically
when the ice storage bin is full.

Because of new plumbing connections, the first production of ice cubes may be
discolored or have an odd flavor. These should be discarded until the cubes made
are free of discoloration and taste. Remember that water quality
determines your ice quality. It is best to connect the ice maker to water that is not
softened. Chemicals from a malfunctioning softener can damage the ice maker.
If the ice maker is connected to soft water, ensure the softener is maintained and
working properly.

To stop the ice maker, lift the wire signal arm until it clicks and locks in the "up"
or OFF position.

8

Automatic Ice and
Water Dispenser

(continued)

Do not use the ice

WARNING

chute as a handle when removing
or replacing the ice storage bin.
Surfaces there may be sharp.

Ice Dispenser Tips

1. Ice cubes stored too long may develop an odd flavor. Empty the container and

return it to the proper position. The ice maker will then produce more ice.

2. Occasionally shake the container to keep ice separated.

3. If the dispensing bar is pushed in for more than 4 minutes, the dispenser

motor may overload and stop. The overload protector will reset
automatically after 3 or 4 minutes. If a large quantity of ice is needed at
one time, it is best to remove cubes directly from the ice storage bin.

4. Certain sounds are normal when the ice maker is operating. They are:

• Motor operation

• Ice being loosened from the tray

• Ice dropping into the storage bin

• Running water

• Water valve opening or closing
For more information on these operations, see "Normal Operating Sounds."

5. Stop the ice maker when cleaning the freezer or for long vacations.

6. If the ice maker is to be turned off for a long period of time, turn the

water supply valve to the closed position.

Cleaning the Ice Dispenser

Clean the dispenser and ice storage bin at regular intervals, particularly before you
take a vacation or move, or if the ice dispenser sticks.

1. Stop ice production by lifting the wire signal arm to the "up" or OFF position.

2. Remove ice storage bin by lifting up and out. Empty and carefully clean the

bin with mild detergent. Do not submerge the bin while cleaning. Rinse with
clear water. Do not use harsh or abrasive cleaners. Allow ice bin to dry
completely before replacing in the freezer.

3. Remove ice chips and clean the shelf and chute that supports the ice storage

bin.

4. Replace the ice storage bin. Lower the wire signal arm on the ice maker to

the "down" or ON position and the ice maker will resume production.

IMPORTANT: When removing or replacing the ice bin, do not rotate the auger

in the ice bin. If the auger is accidentally turned, you must realign the auger by
turning it in 90° turns until the ice bin fits into place with the drive mechanism.
For further instruction, see the label on the ice bucket.

Remove and empty the ice storage bin if:

1. An extended power failure (one hour or longer) causes ice cubes in the ice

storage bin to melt and freeze together and jam the dispenser mechanism.

2. The ice dispenser is not used frequently. Ice cubes will freeze together in the

bin and jam the dispenser mechanism. Remove the ice storage bin and shake
to loosen the cubes.

NEVER use an ice pick or similar sharp instrument to break up the ice. This could
damage the ice storage bin and dispenser mechanism.

9

Automatic Ice and
Water Dispenser

(continued)

Order new filter cartridges through
the dealer where you bought the
refrigerator. It might be good to
order some filters when you first
install your refrigerator. Be sure to
ask for the RC-200 replacement
cartridge.

Ice and Water Filter (some models)

NOTE: If you purchased a refrigerator with a Ice and Water filter, please
read the following use and care information.

This ice and water filter system filters water to your ice maker and water dispenser.
It is located in the upper right back corner of the fresh food compartment (see
Figure1).

System Startup:

Water supply does not need to be turned off, however do not use ice and water
dispenser while installing filter. Refer to Figure 1 as you complete these instructions.

The filter cartridge has already been installed in the filter housing at the factory. Refer
to the How the Dispenser Works section to properly fill the system with water.

Changing the Filter:

Water quality varies throughout the world. To ensure the highest possible water
quality, change water filter every 6 months, or 200 gallons. Also, if filter has been
in a refrigerator that has not been in use for awhile (during moving for example),
change filter before reinstalling refrigerator. Note dispenser system will also operate
without filtration (with filter cartridge removed).

To change filter:

Refer to Figure 1 as needed. It is not necessary to turn the water supply off to change
the filter.

1. Set ice maker lever (wire signal arm) to the OFF (up) position.

2. Hold filter cup firmly, and unscrew counter clockwise (Figure 1). (Some water could
leak out as you remove cup. This is normal.) Filter cartridge should come down
with cup. If cartridge remains in housing, pull down gently, while twisting filter
back and forth.

3. Empty cup of any substance.

4. The large o-ring (Figure 1) that seals the filter system sets in the o-ring groove down
inside the cup. Should the o-ring fall out during filter cartridge replacement, simply
place it back in the groove prior to screwing the cup back in place. If the o-ring
becomes damaged, you will need to order a new one from the Consumer
Assistance Center.

5. Discard old filter cartridge.

6. Remove new filter cartridge from packaging, and install.

7. Place filter cartridge in cup. The end with the small o-ring should be up, out of the
cup.

8. Screw cup, with filter, back onto housing. Filter cartridge will self-align as cup is
tightened. Be sure cup is completely tightened. Do Not Tighten Past Stop.

9. Set ice maker level on the ON (down) position.

10

Figure 1

Automatic Ice and
Water Dispenser (continued)

WHITE WESTINGHOUSE ICE AND WATER FILTER SYSTEM

SYSTEM SPECIFICATION AND DATA SHEET

APPLICATION GUIDELINES / CONDITIONS OF USE

WATER SUPPLY:
WATER

TEMPERATURE:
WATER

PRESSURE:

• Timely cartridge replacement is essential for the product to perform as advertised. Please refer to the Use and Care
Manual for general operation and maintenance requirements. Your refrigerator will have one of two types of filter
replacement reminders. One is a simple slide knob on the rear control box that you set to six months after installing a
new filter. The other is an electronic light on the freezer door dispenser that lights up yellow when the filter is almost
ready for replacement and lights up red when the filter must be replaced. The indicator is pressed for approximately
10 seconds to reset after replacing the filter.

• Ice & Water Filter System RF-200 should not be used on water that is microbiologically unsafe or with water of
unknown quality without adequate disinfection before or after the system. System may be used on disinfected waters
that may contain filterable cysts.

• Performance may vary based on local water conditions and/or pressure. High sediment areas may require more
frequent filter replacement.

• Ice & Water Filter System will absorb bad tastes and odors in both ice cubes and drinking water.

SYSTEM SPECIFICATIONS

FLOW RATE:

CAPACITY:

Municipal or Well applications

Maximum 100° F. (38° C.) For cold water use only

125 psi maximum Recommended Minimum: 30 psi, as measured at the valve inlet

Ice Maker - 3.4 to 4.3 oz (99 - 125 cc) per 7.5 seconds at 60 psi (as measured at valve inlet)
Dispenser - 60 oz per minute (.37 gpm or 1.4 liters per minute) at 60 psi (as measured at valve
inlet)

200 Gallons

SYSTEM
CONSTRUCTION:

REPLACEMENT CARTRIDGE INFORMATION

Replacement RC-200 Cartridges are available through your local dealer.

General testwater parameters; pH = 7.5 +/- 0.5 Temp. 20°C +/- 3°C (68°F +/- 5°F) Pressure = 60 psi

Substance

Reduction

Chlorine N/A 1.9 mg/l 0.11 mg/l 0.04 mg/l 97.80% N/A 94.80%
Lead-6.5PH N/A 0.15 mg/l 0.001 mg/l 0.001 mg/l 99.30% 15.0 ug/l 99.20 %
Lead-8.5 PH N/A 0.16 mg/l 0.003 mg/l 0.002 mg/l 98.75% 15.0 ug/l 97.90%
Atrazine N/A .0099 mg/l .0006 mg/l .0005 mg/l 94.90% 3.0 ug/l 92.60%
2,4 D N/A 0.32 mg/l 0.04 mg/l 0.018 mg/l 94.20% 70 ug/l 85.20%
Cysts 3 to 4 122500 ppm 20 count/pm 10 count/pm 99.99% N/A 99.98%
Particulates .5 to 1 240000 ppm 880 ppm 410 ppm 99.80% N/A 99.50%
Turbidity 23 - 28 NTU 26 NTU 0.09 NTU 0.07 NTU 99.70% N/A N/A

Filter Housing Assembly - ABS Plastic
Water Storage Tank - Polypropylene Plastic
Tubing - Polypropylene / Polypropylene Plastic
Filter Media - Extruded Carbon block with Polypropylene prefiltration shells

Particle Size

Range

(microns)

Average

Influent

Maximum

Effluent

Average

Effluent

Reduction

Average

%

EPA

M.C.L.

Minumun

%

Reduction

11

Care and Cleaning

Damp objects stick to cold
metal surfaces. Do not touch refrigerated
surfaces with wet or damp hands.

To avoid damage and help
the refrigerator run as efficiently as
possible, clean the condenser and air
vents periodically.

Keep your refrigerator and freezer clean to prevent odor build-up. Wipe up any spills
immediately and clean both sections at least twice a year. Never use metallic
scouring pads, brushes, abrasive cleaners or strong alkaline solutions on any
surface. Do not wash any removable parts in a dishwasher.

Always unplug the power cord from the wall outlet before cleaning.

NOTE: Turning the control to OFF does not disconnect power to the controls, light
bulb, or other electrical components.

Inside

Wash inside surfaces of the refrigerator and freezer with a solution of 2 tablespoons
baking soda in 1 quart warm water. Rinse and dry thoroughly. Be sure to wring

excess water out of sponge or cloth before cleaning around the controls,
light bulb, or any electrical parts.

Wash removable parts such as shelves and drawers with baking soda solution or mild
detergent and warm water. Do Not Use Harsh Cleaners On These Surfaces. Rinse
and dry thoroughly. Clean the door gaskets with mild suds, rinse with clear water and
wipe dry. Do not use razor blades or other sharp instruments which can scratch the
appliance surface when removing adhesive labels. Any glue left from the tape or
energy label can be removed with a mixture of warm water and mild detergent, or,
touch the residue with the sticky side of tape already removed. Do Not Remove The

Serial Plate.

Outside

Wash the cabinet and handles with warm water and mild liquid detergent. Rinse
well and wipe dry with a clean soft cloth. Do not use commercial household
cleaners, ammonia, or alcohol to clean handles.

Remove any dust or dirt from the front of the toe grille using a vacuum cleaner with
its dusting tool attachment. Remove the toe grille by pulling it straight out. While the
grille is removed, vacuum the backside of the grille and wipe with a sudsy cloth or
sponge. Periodically clean the condenser (black tubes and wires beneath the
refrigerator, behind the toe grille). Do not allow lint or dust to accumulate on the coils.
Insert a long handled brush or vacuum attachment between the two coils to bring the
lint forward. To replace the toe grille, line up clips with holes and push grille straight
on. Use caution when cleaning in the area of the coils. Surfaces

there may be sharp.

The air vents on the lower access panel at the rear of the refrigerator should be
cleaned periodically. Clean the vents by using a vacuum cleaner with its dusting tool
attachment. When moving the refrigerator, pull straight out. Do not shift the
refrigerator from side to side as this may tear or gouge the floor covering. Be careful
not to move the refrigerator beyond plumbing connections.

Replacing the Light Bulb

To replace the light bulb in either compartment:

1. Unplug the refrigerator.

2. Wear gloves as protection against possible broken glass.

3. Replace old bulb with an appliance bulb of the same wattage.

4. Remember to plug the refrigerator back in.

12