The Matrix 100 Handheld Metal Detector is a world class security scanner. It is designed
to meet and exceed the needs and specifications of today’s security conscious world, and
complies with all National Institute of Justice standards for indoor/outdoor operations
(IP 54). “Made in the U.S.A.” is a hallmark of White’s Electronics, the Matrix 100 utilizes
the latest in electronic design technology that is both functional and attractive.
The Matrix 100 Handheld Metal Detector is designed to detect metal and is primarily for
security applications, however it is useful for a myriad of detection applications.
Contact Information .............................................................................Back Cover
Features – Front view
888-778-9010www.whiteselectronics.com
3
Features—Front View
Visual indicator LED
ON/OFF LED and
Low battery indicator
ON/OFF button
Features – Back view
De-sense button
Lanyard
hole
Audio speaker
Battery door
888-778-9010www.whiteselectronics.com
4
Features—Back View
Visual indicator LED
Lanyard
hole
Battery
door
De-sense button
Sensitivity
control
access
hole
Volume
control
access
hole
20 cm
Scan area
Earbud jack with
rubber plug
888-778-9010www.whiteselectronics.com
5
Features—Top Edge
Battery
door
Lanyard hole
De-sense button
Features—Bottom Edge
20 cm
Visual indicator LED
20 cm
Scan area
Earbud jack and
rubber plug
Battery
door
Scan area
Mechanical Drawing-metric Dimensions
888-778-9010www.whiteselectronics.com
6
Features—Battery Door
Battery door
Stylus
Battery polarization graphic
888-778-9010www.whiteselectronics.com
7
ON/OFF Button
There are three selections for the ON/OFF button:
• ON Audio
• ON Vibrate
• OFF
ON Audio—press the ON/OFF button once. This will be followed
by a single, double, or triple beep to indicate the current sensitivity
level setting. The green ON indicator LED will emit a single flash
for low sensitivity, double flash for medium sensitivity or a triple
flash for high sensitivity.
ON Vibrate—press the ON/OFF button twice. This will be followed
by a single vibration burst and the ON indicator LED will emit a
single flash for low sensitivity, double flash for medium sensitivity,
or a triple flash for high sensitivity. The audio alarm is deactivated
when the vibrate alarm is activated.
OFF—Turn the unit off by pressing the ON/OFF button once. The
ON indicator LED will disappear.
Earbud jack
ON/OFF indicator LED
ON/OFF button
Speaker
888-778-9010www.whiteselectronics.com
8
Sensitivity Control
The unit is preset, at the factory, to medium sensitivity. The sensitivity level
can be changed to the low, medium, or high level.* The Specifications List
(see Page 20) shows the effect of the different sensitivity levels for detecting
objects of various sizes.
To change the sensitivity level, open the battery door and remove the stylus
(see Page 7). Use the stylus to press the sensitivity control to cycle through the
sensitivity levels,(low, medium, or high). The unit will beep or vibrate and
will flash the red visual indicator LED to announce the new sensitivity level:
One beep/vibration/flash = low sensitivity
Two beeps/vibrations/flashes = medium sensitivity
Three beeps/vibrations/flashes = high sensitivity
When the unit is turned off or the battery is removed, the sensitivity level
setting is retained in the memory.
Visual indicator LED
De-sense button
Earbud volume
Sensitivity
Stylus
* To be determined by administration policy and supervisor control.
888-778-9010www.whiteselectronics.com
9
Volume Control for the Earbud
The unit is preset, at the factory, to medium earbud volume. Adjustments to
volume must be made in audio mode. Press the volume control to cycle through
the volume levels of low, medium, or high.* The unit will beep or vibrate and
will flash the red visual indicator LED to announce the new volume level:
One beep/one flash = low volume
Two beeps/two flashes = medium volume
Three beeps/three flashes = high volume
When the earbud is plugged into the scanner, the audio speaker is deactivated.
When the unit is turned off or the battery is removed, the ear bud volume level
setting is retained in the memory.
Earbud volume
Stylus
Sensitivity
* To be determined by administration policy and supervisor control.
Testing the Scanner
• Turn on the scanner in the “ON Audio” or “ON Vibrate” mode.
• Pass the scanner over a metal test object to ensure the LED, audio alarm, or
the vibrate alarm are functioning properly. If the battery is fresh or recently
recharged (more than 7V), the LED next to the ON/OFF button will produce
a green light (see Page 8). If the battery is discharged to less than 7V, the
LED will produce a yellow light and it is recommended that you replace the
battery.
888-778-9010www.whiteselectronics.com
10
Batteries
One 9V battery is included with the Matrix 100. Use a 9V-alkaline,
9V-lithium-manganese dioxide, or externally charged 9V-battery. If the battery
is fresh or recently recharged (more than 7V), the LED next to the ON/OFF
button will produce a green light. If the battery is discharged (less than 7V)
the LED will flash a yellow light and it is recommended that you replace the
battery.
Battery Life
Based upon measurements, battery life for a 600 mA-hour alkaline battery at
room temperature is:
HoursDays
ON2169
OFF2880120
Battery life is doubled with the 1200 mA-hour lithium-manganese dioxide
batteries.
Rechargeable 9V batteries can also be used, but battery life per charge
is typically much shorter than the life of 9V-alkaline batteries, and
depends upon the battery type and the battery recharging system.
WARNING
DO NOT use the earbud jack as a recharging port!
Use of the earbud jack as a recharging port may
damage the Matrix 100 or the battery charger,
and will void the warranty.
Battery Temperature Ratings
Alkaline batteries are rated by the following manufacturer:
Energizer -18°C to 55°C (0°F to 130°F)
Panasonic -20°C to 54°C (-4°F to 130°F)
Lithium-manganese dioxide batteries are rated by the following manufacturer:
Duracell -20°C to 60°C (-4°F to 140°F)
Energizer -40°C to 60°C (-40°F to 140°F)
Ultralife -20°C to 60°C (-4°F to 140°F)
Manufacturer’s ratings are based upon operating loads quite different from
the Matrix 100, so it is possible to have different results.
* For information about special batteries that will operate at
temperatures as low as -40°C contact White’s Electronics, Inc.
888-778-9010www.whiteselectronics.com
11
Battery Installation
• Gently slide the battery door open.
• Slide a 9V battery into the battery cavity as shown below.
• Close the battery door.
L
888-778-9010www.whiteselectronics.com
12
De-Sense button
On the top edge of the scanner, there is a large rubber “De-sense” button.When
depressed, this button will reduce the detectors sensitivity by approximately
50%. This is particularly useful when scanning near rebar reinforced floors.
The “De-sense” is only activated as long as the button is depressed. While
the “De-sense” button is pressed the ON/OFF LED (see Page 4) will illuminate
continuously. If the battery is good, the LED will be green. If the battery is low
or defective the LED will be yellow.
Visual indicator LED
De-sense button
888-778-9010www.whiteselectronics.com
13
Earbud jack
The earbud jack accepts a 3mm or 1/8" “Mono” connector.
Earbud jack
Earbud Jack Rubber Plug
The rubber plug helps protect the earbud jack against dirt and moisture.
Earbud jack rubber plug
888-778-9010www.whiteselectronics.com
14
Lanyard
A lanyard is provided with each Matrix 100. The small nylon loop can be
threaded through the lanyard hole and looped back through itself to secure
the Matrix 100. The lanyard is tested to withhold approximately 25 pounds of
force, before breaking.
Scanning a Person
• Warning: Follow the approved policy & procedure for scanning a person.
This policy & procedure should be approved by the administrator and/or
supervisor of the person using the scanner.
• It is recommended that the operator “NOT” touch the individual being scanned
with the detector.
• The detector is not a weapon and should not be treated as such and will void
the warranty.
• Treat the detector with care. Do not abuse.
National Institute of Justice
Guidelines for use of handheld detectors in schools.
While it is not difficult to learn to use a handheld metal detector correctly,
school administrators should not underestimate the value of annual training for
their operators, as well as training for staff who may be called upon to serve as
backup or supplemental operators. However, on-the-job practice is important
in allowing the school to achieve the type of throughput that will be required in
order to process students quickly.
Every school will want to tailor its own set of operator procedures to take into
consideration its students’ and community needs. Some generic procedures:
• The detector should be passed over the scannee’s body at a distance of no
more than 3 to 4 inches. Avoid touching the body or clothing with the detector.
However, for some baggier clothing, such as pants or jackets, it may be necessary
to hold the detector against or more into the fabric while scanning in order to
stay within 3 to 4 inches of all body surfaces.
888-778-9010www.whiteselectronics.com
15
Scanning a Person
• Most handheld metal detectors should be set at their highest sensitivity;
an exception to this is if there is significant interference from metal reinforcing
in a floor or other nearby material that could cause constant alarms unless the
detector’s sensitivity is turned down.
• The body scan should be performed each time in the same pattern so that
the operator always knows what parts of the body still need scanning. A sample
routine is illustrated on Page 18.
1. Ask the scannee to place all carried items, plus any caps or headgear on
a table (procedures for manual search of baggage are not covered in this text).
The scannee should stand with his or her feet about 18 inches apart, facing away
from the table and about 2 feet in front of it. Footprints outlined on the floor or
drawn on a mat can greatly help position the scannee properly. Ask the scannee
to hold his or her arms out to the sides, parallel to the floor.
2. Quickly run the handheld detector across some piece of conductive
material on your own body, such as a belt buckle. The ensuing squeal of the
detector will assure you that the scanner is still operating properly.
3. Start at the top of one shoulder of the scannee. With the paddle of the
detector held horizontally and parallel to the front of the body, sweep down one
side of the front of the torso, down the leg to the ankle, then move to the other
ankle and sweep back up the front of this opposite leg and torso, ending with
the opposite shoulder. (If a particular detector’s detection paddle is less than
half the width of the average body, or if a particular body is wider than twice the
width of the detection paddle, the pattern will have to be modified to achieve
adequate coverage).
4. Sweep the detector paddle over the outside top of the arm from the top
of the shoulder to the bottom of the wrist, then up the inside of the arm to the
armpit. Sweep down that side of the body to the ankle, then up the inside of that
leg and down the inside of the opposite leg, then back up the other leg from the
ankle to the underarm. Repeat the sweep of the inside and outside of this arm.
Note that it would be particularly important to avoid touching the paddle up
against the scannee’s body when scanning up and down between the legs.
5. Ask the scannee to turn around. (Arms can be put down now). The pattern
used to scan the front of the body should now be repeated over the back of the
body.
6. Ask the scannee to grab the edge of the table for support, then to lift one
foot up in back of him or herself. Scan across the bottom of the shoe. Repeat
for the other foot. The operator should expect to hear a short squeal from the
detector when scanning the bottom of shoes or boots with steel shanks or steel
toes. Both shoes should cause equivalent squeals.
7. For the head area, start at the top of the forehead and scan around the
888-778-9010www.whiteselectronics.com
16
Scanning a Person
top of the head down to the back of the neck.
• When the detector identifies a suspicious item and there is no visible
source for the alarm (clothing is shielding the source object), ask the person to
show you what they have in that area. For example, for an alarm along the arm
or wrist, have the scannee pull up his or her shirt sleeve. Using your detector,
duplicate the squeal you heard before, but now over the visible item.
• Do not let the scannee influence you as to what is actually causing an
alarm. For instance, if the detector denotes the presence of a suspicious item
under a shirt sleeve, do not fail to completely investigate the source of the
alarm even though the scannee assures you that it is just his or her watch.
• If the person you are about to scan caused an alarm when walking through
a portal metal detector, and your job is to try to locate the source of that alarm
on his or her body, do not stop the complete scanning process just because you
come across one alarm-causing item. Continue the scan even though you find
one or more items in the process.
• The lower abdominal area is particularly difficult to scan because this area
is private in nature and because of the metal items usually found in this area:
belt buckles, metal buttons or snaps, and metal zippers. When doing the initial
front body scan, if an alarm occurs in this area, there are two possible ways to
further investigate:
a. Ask the scannee to undo any belt he or she might have on and have him
or her pull the belt ends away from the middle of the body. Now scan the zipper
area; your handheld metal detector should tell you if it is now only sensing a
zipper and/or a metal snap, or if a more suspicious item is present and further
investigation is needed.
b. A second approach that some schools use is that, if the lower abdominal
area is causing an alarm on the handheld detector, ask the scannee to bend
the front of his or her front waistband forward, to ascertain that no weapon
is hidden behind it. Facilities need to be available for situations where
further investigation can be accomplished privately, but only in the presence
of two or more school employees who are the same gender as the scannee.
888-778-9010www.whiteselectronics.com
17
Scanning a Person
This is an example of procedures for using a handheld metal detector that has at least a
10-inch zone of direction.
(The preceding guidelines and illustrations were produced by the National Institute of
Justice in their report titled The Appropriate and Effective Use of Security Technologies
in U.S. Schools. National Institute of Justice, U.S. Department of Justice: Washington, DC
(September 1999) Available online at: http://www.ojp.usdoj.gov/nij/pubs-sum/178265.
htm)
There have been no conclusive studies showing that the magnetic fields
generated by handheld metal detectors will or will not affect personal medical
electronic devices (PMEDs), such as pacemakers, cardiac defibrillators,
infusion pumps, spinal cord stimulators, etc. Therefore, caution should be
used when operating handheld metal detectors near people with the PMEDs.
888-778-9010www.whiteselectronics.com
18
Three–year Warranty
The Matrix 100 is warranted by White’s Electronics, Inc., under normal use,
against manufacturing defects for three years from the date of purchase.
Equipment returned to an authorized repair center or to the factory during
the warranty period will be inspected and evaluated under the performance
specifications. White’s Electronics will repair or replace, at no charge to the
owner, all parts determined to be faulty. Items not covered by this warranty
are as follows:
• Batteries
• Failures caused by abuse
• Tampering with the internal electronics
• Battery leakage
• Repairs made by an unauthorized party
• Contaminants
• Use in adverse conditions.
Returns must be prepaid and shipped to:
Whites Electronics, Inc.
Security Division
Repair Department
1011 Pleasant Valley Road
Sweet Home, OR 97386
1-541-367-6121
Specifications
AlarmVisual indicator LED with audio or vibrate function
Battery Consumption 2.8 mA
Dimensions
Length16"/41 cm
Width2 ¾"/3 cm
Thickness1.17"/3 cm
Operating frequency125 kHz
Weight
0602.03 High Medium Low
Sensitivity measured from surface of detector to surface of object)
Large object size class (zinc gun)
Scan speed 0.5 to 2.0 m/s 8 cm (3.1") 11.6 cm 8.6 cm 5.7 cm
Scan speed 0.1 m/s 5 cm (2") 11.6 cm 8.6 cm 5.7 cm
Medium object size class (steel knife)
Scan speed 0.5 to 2.0 m/s 6 cm (2.4") 11.5 cm 9.4 cm 6.3 cm
Scan speed 0.1 m/s 5 cm (2") 11.5 cm 9.4 cm 6.3 cm
Medium object size class (aluminum knife)
Scan speed 0.5 to 2.0 m/s 6 cm (2.4") 7.0 cm 5.3 cm 3.5 cm
Scan speed 0.1 m/s 5 cm (2") 7.0 cm 5.3 cm 3.5 cm
Small object size class (steel handcuff key)
Scan speed 0.1 to 2.0 m/s 3.5 cm (1.4") 7.3 cm 5.6 cm 3.1 cm
Very small object size class (brass pen refill)
Scan speed 0.1 to 2.0 m/s 1.5 cm (0.6") 5.2 cm 3.1 cm 1.9 cm
Extremely small object size class (18-gauge stainless hypodermic needle)
Scan distance and speed Undefined 1.2 cm 0.2 cm NA
Large metal panel interference alarm distance Less than 50 cm 43 cm 33 cm 21 cm
(19.7")
Scan area is cylindrical 28 cm long. Diameter is 2x the sensitivity distance for the object class plus 2 cm.
Scan speed
All object size classes 0.1 to 2.0 m/s 0.05 to 3.0 m/s
Scan range
Large object size class
Scan speed 0.5 to 2.0 m/s +/- 8 cm (3.1")
Scan speed 0.1 m/s +/- 5 cm (2")
Medium object size class +/- 10 cm (3.9" ) at scan
Scan speed 0.5 to 2.0 m/s +/- 7 cm (2.8") speeds from 0.05 to 3.0 m/s
Scan speed 0.1 m/s +/- 5 cm (2") for all object size classes
Small object size class
Scan speed 0.1 to 2.0 m/s +/- 5 cm (2")
Very small object size class
Scan speed 0.1 to 2.0 m/s +/- 2 cm (0.8")
Operating temperature (NIJ indoor/outdoor) -37°C to +65°C -40°C to +85°C
-35°F to +149°F -40°F to +185°F
Relative humidity 95% 20°C to 60°C 95% 20°C to 60°C
Audible alarm volume 75 dB at 80 cm 85 dB at 80 cm
Battery One 9V
Battery life 16 hours 19°C to 23°C 9V–Alkaline 215 hours
9V–lithium 430 hours
Body interference No alarm when touching hand No alarm when touching hand
Electromagnetic emission CISPR 22, Class B CISPR 22, Class B
Weight Less than 500 g 316 g (11 oz) with battery
Operating frequency 125 KHz
Peak magnitude of generated magnetic field at surface of detector 0.2 gauss
888-778-9010www.whiteselectronics.com
20
Accessories
Batteries/Chargers
Lithium-manganese dioxide battery (-20°C to +60°C)
9V rechargeable battery
4 Station Charger
10 Station Charger
Earbud
Earbud Jack Plug
Holster
Lanyard
Stylus
Matrix Security Support, Academy, Store,
Security SupportSecurity AcademySecurity Store
FAQs
On-line Chat
Telephone
Email
The Security Academy
offers hands-on training
instruction at your facility, by our security experts, to train and guide
Ballistic Nylon Briefcase
Batteries
Battery Chargers
Caps
DVD
your Security Staff in the
most up-to-date security
Earbud
technology available.
Prices available on request.
Earbud Jack Plug
Holster
Lanyard
Shirts
Stylus
Sweatshirts
Warm–up–suits
For addition information regarding Security Support, Academy, or Store please visit
our web site at www.whiteselectronics.com or call our friendly Customer Service
Representatives at 888-778-9010.
Maintenance
Perform daily inspection to ensure the Matrix 100 is operating properly.
Inspect the battery to ensure it is “fresh” or charged and that the Matrix 100 is
clean.
888-778-9010www.whiteselectronics.com
21
Security Distributors
Western Region Central Region Eastern Region
Randy Smith Mike Brighty Mike White
Alaska
Arkansas
Arizona
California
Colorado
Hawaii
Idaho
Iowa
Kansas
Louisiana
Mississippi
Missouri
Montana
Nebraska
Nevada
New Mexico
Oklahoma
Alabama
Florida
Illinois
Indiana
Kentucky
Michigan
Minnesota
North Dakota
Ohio
South Dakota
Tennessee
Wisconsin
Canada
Connecticut
DC
Delaware
Georgia
Maine
Maryland
Massachusettes
New Hampshire
New Jersey
New York
North Carolina
Pennsylvania
Rhode Island
South Carolina
Vermont
Virginia
West Virginia
Oregon
Texas
Utah
Washington
Wyoming
Mexico
Caution: Any device changes or modifications not expressly approved by Whiteʼs Electronics, Inc. could void the userʼs authority
to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that may
causeundesired operation.
This “Class B” digital apparatus complies with Canadian ICES-003.
Cet appareil numériqué de la “classe B” est conformé à la norme NMB-003 du Canada.
888-778-9010www.whiteselectronics.com
22
Washington
Oregon
Montana
Idaho
California
Nevada
Utah
Arizona
New Mexico
Colorado
Nebraska
South Dakota
North Dakot
a
Kansas
Oklahoma
Texa
s
Hawaii
Wy
oming
Minnesota
Iowa
Missouri
Illinoi
s
Wisconsin
Michigan
Ohio
Indiana
Kentucky
Tennessee
North Carolina
South Carolina
Louisiana
Pennsylvania
New York
West
Virginia
Virgini
a
Mississippi
Alabama
Georgia
Florida
Maine
Vermont
New Hampshire
Massachusettes
Rhode Island
Connecticut
New Jersey
Delaware
Maryland
Alaska
Randy Smith, Western Region - Tulsa OK
Phone: 1-888-778-9010
rsmith@securitymetaldetectors.com
Michael Brighty, Central Region - Toledo OH
Phone: 1-888-778-9010
mbrighty@securitymetaldetectors.com
Michael White, Eastern Region - Boston MA
Phone: 1-888-778-9010
mwhite@securitymetaldetectors.com
Arkansas
Security Distributors
888-778-9010www.whiteselectronics.com
23
METAL DETECTORS
TM
SECURITY DIVISION
1011 Pleasant Valley Road
Sweet Home, OR 97386
1-888-778-9010 Toll Free
541-367-6121 Voice
541-367-7990 Fax
P/N 621-0495Printed in USA 04/07
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.