WHITECROFT LIGHTING ACL INDUSTRY Installation Leaflet

GENERAL INFORMATION

1. A qualified electrician, in
accordance with IEE wiring
regulations, should carry out
connection to mains wiring.

2. Ensure mains power is
turned off during
maintenance.

3. Ensure that the rated voltage
and frequency requirements
are compatible with the

available mains supply.

4. This unit must be
EARTHED.

5. Cleaning of reflectors and
lenses should be carried out
using clean, soft and lint free
cloths and anti-static
cleaning fluid.

6. Do not carry out high voltage
insulation test, i.e.
500/1000v this may damage

internal components.

7. Replacing the light source
within this luminaire shall
only be carried out by the
manufacturer,
service agent or a
similar qualified
person.

SPECIFICATION

Lamp type: LED 4000°K
Control Gear: Fixed Output / DALI

Body Material: Light Grey PC

Diffuser
material:
Supply: 220-240V AC, 50Hz

Operating
temp:

Conductor: 2.5mm2 max

Rating: IP66 / IK08

Weight:
1283mm
1578mm

Opal High Impact PC with
internal prisms

Standard -20°C to 25°C

Emergency -5°C to 25°C

Std 2.75 kg Em. 3.25 kg
Std 3.4 kg Em. 3.9 kg

FURTHER INFORMATION

In common with all IP66 rated fittings the ACL
Industry luminaire is protected against ingress of
dust and water projected from a nozzle. However
care must be taken in the siting of these
luminaires. They can be mounted outdoors under

a canopy or covered environment but should not

be in direct sunlight or open areas exposed to
adverse weather conditions. In particular they
should not be installed in an environment liable to
produce standing water on the fitting or IP glands.

ACL INDUSTRY

Installation Leaflet

PLEASE NOTE: In

freezer applications
product must be
mounted a minimum
of 1M from any
ventilation including
the freezer door.

All measurements in
mm unless stated
otherwise, see website
for product codes and

lumen outputs

Variant Length Cable Entry

Points

0.6m 663 530 390 266

1.2m 1283 1050/1170 800 676

1.5m 1578 1345/1170 1100 976

TECHNICAL SUPPORT Tel: [phone]

e-mail: [e-mail]

Mount Bracket

Centres

Surface Mount

Centres

PK/LEAFLETACLLED

Feb 2019 - Rev G

Whitecroft Lighting Limited

Bu r l i ngton S treet , Asht o n - u nder- L y ne, La n c ashire O L7 0A X
Telephone [phone] Facsimile: [phone]

Registered No. 3848973 England Registered Office: As above

LED INSTALLATION SEQUENCE

1. Remove the luminaire from the
packaging, lift the diffuser and
set it to one side.

2. Remove the gear tray from the housing
by squeezing the plastic clips together
at both ends. (Fig.1)

3. Remove the plastic bag containing the

ceiling fixing kit, diffuser retention clips,

sealing grommets.

4. There are 2 mounting options with the
supplied components - surface
mounted or suspended (Fig. 2).

5. For secure
suspension
i.e. in an area
with a high
risk of lateral
movement use
the
ACFHOOKKIT
(supplied
separately ­additional
rubber washer
required for IP
seal not
included).

6. For direct
surface
mounting use
suitable
screws and
washers
(supplied by others) through the same mounting bosses as the hook kit. Ensure
that washers are correctly fitted to the inside of the bosses to maintain the IP
rating.

ELECTROSTATIC SENSITIVE DEVICE

Page 1

HIGH VOLTAGE LEDs

Fig. 2

Fig. 1

DETECTION AREA

Detection area can be reduced
by selecting the combination
on the DIP switches to fit
precisely for each specific
application.

HOLD TIME

Hold-time means the time
period you would like to keep

the lamp on 100% after the

person has left the detection
area.

DAYLIGHT SENSOR - NOT USED

DEFAULT SETTING I - DISABLED

STAND-BY PERIOD
(CORRIDOR FUNCTION)

This is the time period you
would like to keep at the low
light output level before it is
completely switched off in the
long absence of people.

Note: “0s” means on/off
control; “+ ∞” means bi-level
dimming control, fixture never
switches off.

STAND-BY DIMMING
LEVEL

This is the dimmed low light
output level you would like to
have after the hold-time in the
absence of people.

Page 6

COMMAND 5 SENSOR WITH SETBACK
DIP SWITCH CONFIGURATION

Model: HCD418

The sensor is a motion
switch. It turns the light ON
after detection of moving
objects and turns the light
OFF after a pre-selected
hold-time when there is no
motion detected.

7. Bring the incoming supply wires into the luminaire body through the knock-outs at
the end of the body or on the rear (Fig.3) using the supplied sealing grommets.
Seal any unused cable entry holes with the closed grommets supplied.

Fig. 4

DALI

MAINS

DALI EM /
COMEPS

INSTALLATION OF LUMINAIRE

Note: Important to consider

 The sensor provides DALI output to the driver to perform on / off / setback

control only. The sensor must not be connected to a DALI network.

 The sensor can detect movements though thin walls and glass; detection

range (sensitivity) should be adjusted in accordance with site conditions.

 Luminaire must be fixed to a solid surface to avoid false-triggering caused by

vibration.

 Large metal surfaces can cause unwanted detection.
 Ventilation shafts and airflow can cause unwanted detection.
 Luminaires mounted within each other’s detection range may need their

sensitivity reduced to avoid possible nuisance switching.

DETECTION AREA PATTERN

Fig. 5

CLICK!

Fig. 6

10. Clip the gear tray back into the housing. (Fig.5)

11. Set sensor dip switch configuration if
applicable. (see pages 3-6)

12. Remove the two anti tamper screws from the gear tray for fixing diffuser clips.
(Fig. 6)

8. Lift the gear tray back
into position and hook
onto the plastic
retention clips within
the housing. (Fig.4)

9. Make all electrical

connections to the

terminal blocks (Fig.4)
and connect the
emergency batteries if
applicable.

13. Fit the diffuser back into position using all of the retention clips and secure two
plastic clips on opposite sides with the anti-tamper screws provided. (Fig.6)

Page 2 Page 5

COMMAND 5 ECO SENSOR
DIP SWITCH CONFIGURATION

Model: HC005s

The sensor is a motion
switch. It turns the light ON
after detection of moving
objects and turns the light
OFF after a pre-selected
hold-time when there is no
motion detected.

INSTALLATION OF LUMINAIRE

Note: Important to consider

 The sensor can detect movements though thin walls and glass; detection

range (sensitivity) should be adjusted in accordance with site conditions.

 Luminaire must be fixed to a solid surface to avoid false-triggering caused by

vibration.

DETECTION AREA

Detection area can be
reduced by selecting
the combination on the
DIP switches to fit
precisely for each
specific application.

HOLD TIME

Hold-time means the
time period you would
like to keep the lamp on
100% after the person
has left the detection
area.

DAYLIGHT SENSOR -

 Large metal surfaces can cause unwanted detection.

 Ventilation shafts and airflow can cause unwanted detection.

 Luminaires mounted within each other’s detection range may need their

sensitivity reduced to avoid possible nuisance switching.

DETECTION AREA PATTERN

Page 3

NOT USED

DEFAULT SETTING I -

DISABLED

Page 4