Whispair X3MD09S5, X3W12S5, X3MD12S5, X3M09S5, X3M06S6.OU/T Operating And Installation Instructions

...

Download

OPERATING AND INSTALLATION INSTRUCTIONS

FOR WHISPAIR RANGEHOODS

UTILISING REMOTE FAN MOTOR UNITS

AIR ENGINEERED

CONGRATULATIONS

Congratulations and thank you for choosing a Whispair rangehood.

To avoid the risks that are always present when you use an electrical appliance it is important that the rangehood is installed correctly and that you read the safety instructions carefully to avoid misuse and hazards.

We recommend that you keep this instruction booklet for future reference and pass it on to any future owners.

AFTER UNPACKING THE RANGEHOOD PLEASE REVIEW YOUR NEW ITEM TO ENSURE THAT IT HASN’T BEEN DAMAGED IN TRANSIT OR IS MISSING ANY COMPONENTS. FAILURE TO REPORT ANY ISSUE WITHIN 72 HOURS OF RECEIPT OF YOUR ITEM MAY RESULT IN ADDITIONAL CHARGES.

TO AVOID THE RISK OF INJURY OR

DAMAGE TO THE PRODUCT IT IS

ESSENTIAL TO READ THESE

INSTRUCTIONS PRIOR TO

INSTALLATION AND USE

IMPORTANT INFORMATION

Information on disposal for users

Most of the packing materials are recyclable. Please dispose of those materials through your local recycling depot or by placing them in a appropriate collection bin.

If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal.

ENVIRONMENTAL TIP

CARTON 1 - HOOD UNIT

You will be supplied with one of the four hood unit options detailed below.

PRODUCT DESCRIPTION & CARTON CONTENTS

OPTION 1 - INTEGRATED HOOD

MODELS INCLUDED:

X3M06S5, X3M09S5, X3MD09S5, X3MD12S5 and X3W12S5

INCLUDED IN THE CARTON:

1. Main hood housing including switch control and led lighting

2. Bafe lters

3. Grease trap

4. Cabinet installation screws

5. Operating & installation guide

OPTION 2 - WALL HUNG CANOPY HOOD

MODELS INCLUDED:

X5L09S5, X5S09S5, X5V09S5, X5R09S5, X5M10S5 and X5N12S5

INCLUDED IN THE CARTON:

1. Main hood housing including switch control and led lighting

2. Bafe lters

3. Grease trap

4. Stainless steel chimney (2x)

5. Chimney bracket

6. Wall mounting bracket

7. Fixing screws

8. Operating & installation guide

OPTION 3 - ISLAND HUNG CANOPY HOOD

MODELS INCLUDED:

X7S09S5, X7V09S5, X7R09S5 and X7N12S5

INCLUDED IN THE CARTON:

1. Main hood housing including switch control and led lighting

2. Bafe lters

3. Grease trap

4. Stainless steel chimney (1x)

5. Ceiling (island) mounting plate

6. Mounting Beams (2x)

7. Threaded rod (4x) and nuts

8. Fixing screws

9. Operating & installation guide

OPTION 4 - CEILING MOUNT CASSETTE AND UNIVERSAL HUNG HOOD

MODELS INCLUDED:

X9C12S5 and X5C10S5

INCLUDED IN THE CARTON:

1. Main hood housing including switch control and led lighting

2. Bafe lters

3. Grease trap

4. Mounting Beams (2x)

5. Threaded rod (4x) and nuts

6. Fixing screws

7. Operating & installation guide

CARTON 2 - FAN MOTOR UNIT

You will be supplied with one of the two fan motor unit options detailed below.

PRODUCT DESCRIPTION & CARTON CONTENTS

OPTION 1 - INLINE FAN SOLUTION (FIG. A)

MODELS INCLUDED:

IL-800 and IP-1140

Unit designed to be located in a roof space and then ducted to an external vent to the outside atmosphere.

INCLUDED IN THE CARTON:

1. KLEENAIR Inline fan motor unit

2. Mounting bracket

3. Mounting screws for vent and fan motor unit

4. Pipe Clamps - 200mm (4x)

5. 200mm Flexi-duct (5 meters in length)

6. Aluminium powder coated wall / eave vent

7. Foam liner for wall / eave installation

OPTION 2 - EXTERNAL FAN SOLUTION (FIG. B)

MODELS INCLUDED:

EL-800, EP-1140 and EPP-2010.

Unit designed to be mounted externally either on an external wall vertically mounted or penetrating through the roof horizontally mounted.

INCLUDED IN THE CARTON:

1. KLEENAIR External fan motor unit

2. Pipe Clamps - 200mm (2x)

3. 200mm Flexi-duct (5 meters in length)

4. Mounting screws for wall installation

5. Foam liner for wall installation

OPTIONAL INSTALLATION ACCESSORIES:

1. HBX200TILE - 200mm Tile Roof Install Kit Includes roof ashing for tile roof, 200mm duct mounting brackets (2x), threaded rod (2x) and nuts (4x).

2. HBX200MET - 200mm Metal Roof Install Kit Includes roof ashing for metal roof, 200mm duct mounting brackets (2x), threaded rod (2x) and nuts (4x).

3. HBX200DUCT - 200mm Duct Extension Kit Includes 200mm Flexi-duct (5 meters length), 200mm inner connector and pipe clamps (2x).

Fig. A

Fig. B

CONDITIONS OF USE AND MAINTENANCE

This rangehood is a domestic appliance which has been manufactured and tested to comply with Australian and New Zealand Standard AS/NZS 60335.2.31 and is designed to work under Australian and New Zealand conditions. The hoods are designed to remove bi-products of cooking – heat, steam, grease and odour.

This appliance is intended for domestic application only. Any other usage is at the owner’s risk and could be dangerous. The manufacturer cannot be held liable for damage resulting from incorrect or improper use or operation. This unit is approved for electrical safety (Please refer RCM E4759).

WHISPAIR reserves the right to change the specication without notice.

All WHISPAIR performance gures are based upon standards developed by the Haus Group, which either comply or are in excess of the government regulated standards.

SAFETY

WARNING: The installation of WHISPAIR rangehoods must comply with the information in this guide. Failure to install the rangehood in accordance with these installation instructions may result in electrical hazards, injury, damage to your appliance and loss of warranty. Specically, failure by the installer to install the screws or xing devices in accordance with these installation instructions may result in electrical hazards. Please install the appliance as detailed in these instructions.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels.

The air must not be discharged into a ue that is used for exhausting fumes from appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room).

There is a re risk if cleaning is not carried out in accordance with the instructions.

Bafe lters and grease trap must be regularly cleaned (every 4 weeks) to reduce the risk of re.

CAUTION: Accessible parts may become hot when used with cooking appliances. Stainless steel bafe lter edges can be sharp when handling and cleaning.

Ensure the rangehood is switched off and power source cable unplugged before carrying out maintenance, to avoid any possibility of electric shock.

Always use non-ammable materials to minimize the risk of re.

Do not ambé under the range hood.

Always cover lit gas burners with pots or pans when cooker hood is in use.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualied persons in order to avoid a hazard.

Please ensure the hood is securely xed to the support as detailed in this guide. The method of xing stated is not to depend on the use of adhesives as they are not a means of reliable xing.

The height of the underside of the lowest part of the hood body must be a minimum of 600mm above an electric cooktop & 650mm above a gas cooktop and a maximum height of 1200mm. If the instructions of the hob specify a greater distance than the minimum detailed, this shall be the minimum height for installation.

DUCTING AND EXTRACTION LEVELS

WHISPAIR ducting is designed to ensure optimum performance for your rangehood. Please follow the installation instructions carefully.

Every WHISPAIR rangehood must be ducted to the Inline or Externally mounted KLEENAIR fan motor unit by the use of non-ammable ducting. The rangehood must not be ducted into a wall cavity or a ceiling space where a build-up of grease can occur and become a potential re risk. Ensure the external outlet on the KLEENAIR unit is not covered and the air ow is not restricted in any way as this may result in reduced performance.

The duct must at all times have a cross sectional surface area equivalent to the hood outlet. The hood outlet has a circular cross section of 200mm in diameter or an approximate area of 31,400mm. Do not reduce the duct size at any time and avoid sharp bends. If the duct run is longer than six (6) metres, it may be necessary to enlarge the duct size to ensure optimum performance. The manufacturer does not guarantee performance when the duct length is greater than six (6) metres.

Ensure that all ducting is correctly tted and sealed with pipe clips, duct tape or silicone to ensure that fumes do not escape prior to reaching the KLEENAIR fan motor unit.

The WHISPAIR extraction calculations are based upon a 50pa change of head of pressure loss and are used to factor the variance of air ow resistance through the ducting. 50pa is equivalent to approximately four (4) metres (the recommended length) of exi ducting with one gentle bend, which is above and beyond the industry standard of one straight metre of ducting. The KLEENAIR LITE offers a powerful 800 cubic metres per hour (223 litres per second) of air movement. The KLEENAIR PRO offers 1140 cubic metres per hour (317 litres per second) whilst for serious users the KLEENAIR PRO PLUS boasts a market leading 2010 cubic metres per hour (558 litres per second).

THE RECOMMENDED DUCT

LENGTH (INSTALLATION DISTANCE)

IS 4 METRES.

THE MINIMUM INSTALLATION

DISTANCE IS 3 METRES.

GENTLE BENDS IN THE DUCTING

ARE RECOMMENDED AS IT ASSISTS

IN MUFFLING NOISE FROM THE

REMOTE FAN UNIT.

To Rangehood Unit

Gentle Bend

In Ducting

NOISE LEVELS & EXTRACTION LEVELS

All KLEENAIR fan motor unit operates at maximum external sound pressure level between 43dB(A) and 76dB(A). The internal operation of the systems will have a varying sound level dependent on the style of hood, the motor option selected, the acoustics of the environment and the installation method used. It was established through testing, in accordance with the Australian Standards, that the internal noise level varied between 33dB(A) and 65dB(A) on the air movement settings available.

It is important to understand that whilst WHISPAIR rangehoods offer quieter operational noise levels due to the positioning of the motor remotely to the primary cooking environment, the noise levels as a consequence of air movement or ‘wind’ noise are equivalent to other premium hoods in the Australian and New Zealand market place, although it must be noted that the extraction levels are signicantly higher.

Extraction Level versus Noise Level

Cubic Meters / Hour of Air Movement

[m/hr]600 1200 1800

A.700 B.800 C.1140 D.2010

Sound Pressure Level

[dB]

Extraction Level Comparison

Cubic Meters / Hour of Air Movement

[m/hr]600 1200 1800

Change in Pressure

100

200

300

400

500

600

700

[Pa]

A. Standard premium rangehood found in the Aus/NZ market offering 700 m/hr B. KleenAir Lite Unit offering 800 m/hr C. KleenAir Pro Unit offering 1140 m/hr D. KleenAir Pro Plus Unit offering 2010 m/hr

A.700 B.800 C.1140 D.2010

SERVICING

The installation and tting of the rangehood should be done in such a way that will allow the unit to be removed if service is required. Additional costs incurred in the removal, such as damage to walls, are not covered under warranty.

It is expected that the stainless steel is cleaned with a quality non-abrasive stainless steel cleaner. The bafe lters and grease trap are removable and dishwasher safe. It is recommended that these items be cleaned regularly.

The KLEENAIR unit should be checked regularly to ensure that nothing is obstructing the air ow from the housing.

PART 1: HOOD INSTALLATION GUIDE

Integrated Hood

Models included: X3M06S5, X3M09S5, X3MD09S5, X3MD12S5 and X3W12S5

STEP 1:

To install into your overhead cupboard, several holes may need to be cut into shelves to enable the ducting to exit the cabinetry. Ensure the hood is mounted as close to the centre of the cooking surface as possible.

NOTE:

The height of the underside of the hood body must be a minimum of 600mm above an electric cooktop & 650mm above a gas cooktop and a maximum height of 1200mm. If the instructions of the hob specify a greater distance than the minimum detailed, this shall be the minimum height for installation.

For installation over a BBQ, the hood can be installed between 1000mm and 1200mm above the cooking surface. Building codes that stipulate a minimum dimension may vary from state to state, please check with your local council prior to installation.

STEP 2:

Refer to Part 2: Motor Installation Guide.

STEP 3:

Remove the three (3) screw xings from within the Main Chassis of the rangehood located along the rear chassis wall (located above the grease trap), along with two (2) screws on the left side and two (2) screws on the right side. Once the screws are removed, the Fascia will separate away from the Main Chassis.

STEP 4:

Fixing Holes are located on the returns of the main chassis. These Fixing Holes are used to secure the main chassis to the cabinetry.

STEP 5:

Place the Main Chassis in the cabinet ensuring that the hood is level and the controls and display will be visible when standing in front of the unit.

WARNING

DIMENSIONS ARE ACCURATE AT THE TIME OF PRINTING, HAUS GROUP RESERVES THE RIGHT TO

CHANGE SPECIFICATIONS WITHOUT NOTICE. FOR BUILDING PURPOSES THE UNIT SHOULD BE

PROVIDED TO THE CABINET MAKER / BUILDER / KITCHEN DESIGNER FOR EXACT MEASUREMENTS.

Outlet

Bafe Filters Grease Trap

Main Chassis

Fascia

Step 3: Remove Fascia from Chassis

Fixing Holes

Step 4: Locate the Fixing Holes of the Main Chassis

PART 1: HOOD INSTALLATION GUIDE

STEP 6:

Using the ten (10) xing holes, screw the Main Chassis into position.

STEP 7:

Once the Main Chassis is secured into the cabinetry, the Fascia can then be slid back inside the Main Chassis. Replace the screws (removed in Step 3) to x the Fascia back into positon. Replace the grease trap.

STEP 8:

Attach the male power plug of the rangehood unit to mains power supply. Note to electricians: Standard 10 Amp General Power Outlet (GPO) required. Position GPO as close to the hood unit as possible.

INSTALLING THE GREASE TRAP AND BAFFLE FILTERS:

All WHISPAIR hoods utilise removable bafe lters and grease trap. This ltration system is used to catch by-products such as grease and moisture from the air ow.

To install the bafe lters, simply locate the lter on the top ledge of the hood and then slide the lter on a downward angle to rest in the channel of the grease trap. Ensure the lter vane are aligned towards the rear of the hood.

Step 7: Insert Fascia into Main Chassis

Most by-products are captured and stored directly in the bafe lters however the grease trap may begin to ll when excess amounts of grease and condensate build up in the lter vanes.

The grease trap can be removed for cleaning by removing the two (2) screw xings in the channel.

To clean your bafe lters and grease trap please wash with warm soapy water or simply place in the dishwasher for convenience. Please

note that the edge’s of the lters can be sharp and caution should be taken when removing or cleaning by hand.

It is recommended the bafe lters and grease trap are cleaned every 4 weeks to reduce the risk of re.

Bafe Filter and Grease Trap Position

Top Ledge

Bafe Filter Grease Trap

Front Rear

PART 1: HOOD INSTALLATION GUIDE

Wall Hung Canopy Hood

Models included: X5L09S5, X5S09S5, X5V09S5, X5R09S5, X5M10S5 and X5N12S5

STEP 1:

Measure the height (H1) of the hood from the base to the top of the Mounting Hooks.

NOTE:

The height (H2) of the underside of the hood body must be a minimum of 600mm above an electric cooktop & 650mm above a gas cooktop and a maximum height of 1200mm. If the instructions of the hob specify a greater distance than the minimum detailed, this shall be the minimum height for installation.

STEP 2:

Using a spirit level mark a vertical centre line on the wall where the Mounting Bracket needs to be positioned. It is recommended to centre the hood unit to the cooktop below.

STEP 3:

Mark a horizontal line on the wall for the Mounting Bracket position. Centre and mark the four (4) xing points in the vertical section on the left and right side of the bracket. Drill and plug holes with suitable sized wall plugs (not provided).

STEP 4:

Fix the Mounting Bracket with four (4) suitable screws into the wall at the positions marked in step 3 to allow the body of the hood to be hung on the wall.

STEP 5:

Hang the hood on the wall ensuring the Mounting Hooks are securely positioned into the Mounting Bracket.

WARNING

DIMENSIONS ARE ACCURATE AT THE TIME OF PRINTING, HAUS GROUP RESERVES THE RIGHT TO

CHANGE SPECIFICATIONS WITHOUT NOTICE. FOR BUILDING PURPOSES THE UNIT SHOULD BE

PROVIDED TO THE CABINET MAKER / BUILDER / KITCHEN DESIGNER FOR EXACT MEASUREMENTS.

Wall Mounting Bracket

Hood Fixing Holes (5x) - Step 6

Wall Fixing Holes (4x) - Step 4

PART 1: HOOD INSTALLATION GUIDE

STEP 6:

Secure the hood to the wall by screw xing through the ve (5x) holes on the horizontal plate of the Mounting Bracket.

STEP 7:

Secure the Chimney Bracket to the wall.

STEP 8:

Refer to Part 2: Motor Installation Guide.

STEP 9:

Place the stainless steel chimney on the hood and secure to the Chimney Bracket with the two (2) screws supplied. If the chimney is required to be lengthened the second internal chimney can be added, telescoping to the required height. If the chimney is required to be shortened, new holes may need to be drilled to secure the chimney cover.

STEP 10:

Attach the male power plug of the rangehood unit to mains power supply. Note to electricians: Standard 10 Amp General Power Outlet (GPO) required. Position GPO as close to the hood unit as possible.

INSTALLING THE GREASE TRAP AND BAFFLE FILTERS:

All WHISPAIR hoods utilise removable bafe lters and grease trap. This ltration system is used to catch by-products such as grease and moisture from the air ow.

Most by-products are captured and stored directly in the bafe lters however the grease trap may begin to ll when excess amounts of grease and condensate build up in the lter vanes.

The grease trap can be removed for cleaning by removing the two (2) screw xings in the channel.

To clean your bafe lters and grease trap please wash with warm soapy water or simply place in the dishwasher for convenience. Please

note that the edge’s of the lters can be sharp and caution should be taken when removing or cleaning by hand.

It is recommended the bafe lters and grease trap are cleaned every 4 weeks to reduce the risk of re.

Chimney Bracket Chimney Fixing Points

Step 9: Chimney Installation

Bafe Filter and Grease Trap Position

Top Ledge

Bafe Filter Grease Trap

Front Rear

PART 1: HOOD INSTALLATION GUIDE

Island Hung Canopy Hood

Models included: X7S09S5, X7V09S5, X7R09S5 and X7N12S5

STEP 1:

Using a weighted string line (plumb line), determine the central position of hood on the ceiling. It is recommended to centre the hood unit to the cooktop below. Mark the position. Before making the cut out, check for obstructions like electrical cables, etc.

NOTE:

STEP 2:

Place the two (2) supplied supporting metal beams (1000mm long) with pre-drilled xing holes perpendicular (90) to the roof trusses.

STEP 3:

Fit the four (4) supplied 10mm threaded rod through the holes provided on the supporting metal beams and secure with nuts and washers provided. Ensure the rod drop height is sufcient to attach the hood and nut xings but is not excessive that is will impede the placement of the lters.

STEP 4:

Feed the Ceiling Plate up the threaded rod and x into position with nuts provided ensure a rm t to the ceiling.

STEP 5 (OPTIONAL):

For additional stability add a second Ceiling Plate (optional) half way between the ceiling and the hood. This will give the mounting additional stability which may be benecial for longer chimney runs.

WARNING

DIMENSIONS ARE ACCURATE AT THE TIME OF PRINTING, HAUS GROUP RESERVES THE RIGHT TO

CHANGE SPECIFICATIONS WITHOUT NOTICE. FOR BUILDING PURPOSES THE UNIT SHOULD BE

PROVIDED TO THE CABINET MAKER / BUILDER / KITCHEN DESIGNER FOR EXACT MEASUREMENTS.

Threaded Rod

Ceiling Plate

Supporting Metal Beams

Step 4

300mm

PART 1: HOOD INSTALLATION GUIDE

STEP 6:

Refer to Part 2: Motor Installation Guide.

STEP 7:

Lift the stainless steel chimney into position and secure to the Ceiling Bracket with the four (4) screws supplied. If the chimney is required to be shortened, new holes may need to be drilled to secure the chimney cover.

STEP 8:

Attach the exi-ducting to the top of the hood unit and x into place with a stainless steel clamp (provided).

STEP 9:

Lift and attach the hood unit to the base of the threaded rod with the provided nuts and washers. Level the unit off by tensioning the 10mm nuts. Being mindful not to over tighten.

Minimise how much threaded rod is below the nut. Excess

threaded rod may interfer with the bafe lters.

STEP 10:

Feed any excess exi-ducting back into the ceiling space ensuring that any excess gathering of ducting is pulled tight. Loose and gathered ducting will reduce the extraction levels.

STEP 11:

Attach the male power plug of the rangehood unit to mains power supply. Note to electricians: Standard 10 Amp General Power Outlet (GPO) required. Position GPO as close to the hood unit as possible.

INSTALLING THE GREASE TRAP AND BAFFLE FILTERS:

All WHISPAIR hoods utilise removable bafe lters and grease trap. This ltration system is used to catch by-products such as grease and moisture from the air ow.

To install the bafe lters, simply locate the lter on the top ledge of the hood and then slide the lter on a downward angle to rest in the channel of the grease trap. Ensure the lter vane are aligned towards the rear of the hood.

Most by-products are captured and stored directly in the bafe lters however the grease trap may begin to ll when excess amounts of grease and condensate build up in the lter vanes.

The grease trap can be removed for cleaning by removing the two (2) screw xings in the channel.

To clean your bafe lters and grease trap please wash with warm soapy water or simply place in the dishwasher for convenience. Please

note that the edge’s of the lters can be sharp and caution should be taken when removing or cleaning by hand.

It is recommended the bafe lters and grease trap are cleaned every 4 weeks to reduce the risk of re.

Lift Chimney

Into Position

(Step 7)

Lift Hood

Into Position

(Step 9)

Hood Mounting Points

Bafe Filter and Grease Trap Position

Top Ledge

Bafe Filter Grease Trap

Front Rear

PART 1: HOOD INSTALLATION GUIDE

Ceiling Mounted Cassette and Universal Hung Hood

Models included: X9C12S5 and X5C10S5

STEP 1:

NOTE:

The height of the underside of the hood body must be a minimum of 600mm above an electric cooktop & 650mm above a gas cooktop. The maximum recommended height for a cassette unit is 1500mm above the cooktop. If the instructions of the hob specify a greater distance than the minimum detailed, this shall be the minimum height for installation.

Building codes that stipulate a minimum dimension may vary from state to state, please check with your local council prior to installation.

STEP 2:

Place the two (2) supplied supporting metal beams (500mm long) with pre-drilled xing holes perpendicular (90) to the roof trusses.

STEP 3:

STEP 4:

Refer to Part 2: Motor Installation Guide.

STEP 5:

Attach the exi-ducting to the top of the hood unit and x into place with a pipe clamp (provided).

WARNING

DIMENSIONS ARE ACCURATE AT THE TIME OF PRINTING, HAUS GROUP RESERVES THE RIGHT TO

CHANGE SPECIFICATIONS WITHOUT NOTICE. FOR BUILDING PURPOSES THE UNIT SHOULD BE

PROVIDED TO THE CABINET MAKER / BUILDER / KITCHEN DESIGNER FOR EXACT MEASUREMENTS.

Threaded Rod

Supporting Metal Beams

PART 1: HOOD INSTALLATION GUIDE

STEP 6:

Lift and attach the hood unit to the base of the threaded rod with the provided nuts and washers. Secure the hood cassette rmly to the underside of the ceiling. Level the unit off by tensioning the 10mm nuts. Being mindful not to over tighten. Minimise how much threaded rod is below the nut. Excess threaded rod may interfer with the bafe lters.

STEP 7:

Feed any excess exi-ducting back into the ceiling space ensuring that any excess gathering of ducting is pulled tight. Loose and gathered ducting will reduce the extraction levels.

STEP 8:

Attach the male power plug of the rangehood unit to mains power supply. Note to electricians: Standard 10 Amp General Power Outlet (GPO) required. Position GPO as close to the hood unit as possible.

INSTALLING THE GREASE TRAP AND BAFFLE FILTERS:

All WHISPAIR hoods utilise removable bafe lters and grease trap. This ltration system is used to catch by-products such as grease and moisture from the air ow.

Most by-products are captured and stored directly in the bafe lters however the grease trap may begin to ll when excess amounts of grease and condensate build up in the lter vanes.

The grease trap can be removed for cleaning by removing the two (2) screw xings in the channel.

To clean your bafe lters and grease trap please wash with warm soapy water or simply place in the dishwasher for convenience. Please

note that the edge’s of the lters can be sharp and caution should be taken when removing or cleaning by hand.

It is recommended the bafe lters and grease trap are cleaned every 4 weeks to reduce the risk of re.

Lift Hood

Into Position

Bafe Filter and Grease Trap Position

Top Ledge

Bafe Filter Grease Trap

Front Rear

PART 2: FAN MOTOR INSTALLTION GUIDE

185

440

702

200

108

Wall

Fan Power Supply

Attached to Internal Hood Unit

200mm Ducting

Attached to Internal Hood Unit Outlet

Gentle Bend In Ducting

Ducting Pulled Tight

Housing Mounts

(Optional Accessory)

Flashing to suit

Metal or Tile Roof

(Optional Accessory)

Fan Power Supply

Attached to Internal Hood Unit

200mm Ducting

Attached to Internal

Hood Unit Outlet

Ducting Pulled Tight

Gentle Bend In Ducting

EXTERNAL KLEENAIR MOTOR SOLUTION

Roof (Upper) and Wall (Lower) Mounted

Roof

Wall

Fan Power Supply

Attached to Internal Hood Unit

200mm Ducting

Attached to Internal

Hood Unit Outlet

Gentle Bend In Ducting

Ducting Pulled Tight

INLINE KLEENAIR MOTOR SOLUTION

Eave (Upper) and Wall (Lower) Vented

Vent & Eave

Fan Power Supply

Attached to Internal Hood Unit

200mm Ducting

Attached to Internal Hood Unit Outlet

Gentle Bend In Ducting

Ducting Pulled Tight

Roof

Vent

70 314

200

390

159

363.5

143.5 125

PART 2: FAN MOTOR INSTALLTION GUIDE

Inline Solution

Models included: IL-800 and IP-1140

Positioning your KLEENAIR Unit:

It is recommended that the KLEENAIR INLINE unit be mounted in a roof space or wall cavity. Please ensure that the KLEENAIR unit is positioned in an environment that is free of other gases to enable an efcient expulsion of the cooking by-products and to ensure that back draft of external gases doesn’t take place.

Please ensure the fan motor is positioned away from other exhausts such as chimneys, gas ues, etc. The inline unit can be mounted so that it ducts directly through the wall or eave vent.

STEP 1:

Establish a suitable position in the roof or wall cavity for the KLEENAIR unit, ensuring that the distance between the KLEENAIR unit and the outside vent is no greater than 800mm. The KLEENAIR unit must be located a minimum

of 3 metres from the hood unit.

STEP 2:

Using the mounting bracket and screws, mount the KLEENAIR unit to a beam, truss or another appropriate structures in the roof or wall space through the rubber grommets. Hang the fan motor unit from the mounting bracket ensuring the mounting bracket is located at the top of the unit. Ensure the direction of airow is toward the outside. The direction of airow is marked on the KLEENAIR unit.

STEP 3:

Cut a 200mm diameter hole in the wall or eave to enable the mounting of the external vent. Please ensure that the hole is cut in a practical position to enable the exi-duct to be secured. Attach the exi-duct to the vent and then mount vent to the wall or eave.

STEP 4:

Attach the exi-duct from the external vent to the outlet of the KLEENAIR unit using pipe clamps. To minimise inefciencies and noise ensure the duct is pulled tight and the 200mm diameter is maintained.

STEP 5:

Gentle bends in the ducting are

recommended as it assists in mufing noise from the fan motor unit back to the rangehood

. If the exi-duct needs to be extended attach two exi-duct ends using a rigid duct insert and secured by pipe clamps (Optional installation accessories HBX200DUCT).

STEP 6:

Attach the male plug of the KLEENAIR unit to the female plug of the rangehood to enable power supply to the fan motor unit. An extension lead (not supplied) of up to ve meters may be added if required.

OutletMounting Bracket

Inlet

PART 2: FAN MOTOR INSTALLTION GUIDE

External Solution - Wall Mounted

Models included: EL-800, EP-1140 and EPP-2010

Positioning your KLEENAIR Unit:

It is recommended that when the KLEENAIR EXTERNAL UNIT is WALL mounted, it is positioned a minimum 1800mm above the ground surface with a downward clearance of 1200mm and with a radial clearance of 600mm. Please ensure that the KLEENAIR unit is positioned in an environment that is free of other gases to enable an efcient expulsion of the cooking bi-products and to ensure that back-draft of external gases doesn’t take place.

Please ensure the fan motor is positioned away from other exhausts such as chimneys, gas fuses, etc. The unit can be mounted so that it ducts directly through the wall.

STEP 1:

Cut a 200mm diameter hole in the wall to enable the rigid duct on the back of the KLEENAIR unit to protrude. Please ensure that the hole is cut in a practical position to enable sufcient clearance around the fan motor unit.

STEP 2:

Remove the mounting bracket from your KLEENAIR unit by twisting the cover in an anti-clockwise direction. Mark at least four mounting points on the wall and pre-drill the holes required.

STEP 3:

The rigid duct may require cutting to suit your particular wall thickness. Attach the exi-duct to the rigid duct on the back of the mounting bracket using the pipe clamps supplied.

STEP 4:

Fix the mounting bracket to the wall using the screws and wall plugs provided. Making sure to secure it at 90 degree’s to the horizontal. A secondary mounting bracket (HBXP24) is available is additional clearance between the wall and outlet is required.

Cover

Inlet

Outlet

Mounting Holes

Primary Wall Mounting Bracket (Supplied)

Secondary Wall

Mounting Bracket (Optional)

Locking Screw

STEP 5:

Feed the power cable through the centre of the mounting bracket and return the KLEENAIR unit onto the mounting bracket and x it by rotating the cover in a clockwise direction noting the locating points. Lock the cover into position by tightening the locking screw.

STEP 6:

PART 2: FAN MOTOR INSTALLTION GUIDE

External Solution - Roof Mounted

Models included: EL-800, EP-1140 and EPP-2010

Inlet

Outlet

Mounting Bracket

Rigid Duct

Positioning your KLEENAIR Unit:

It is recommended that when the KLEENAIR EXTERNAL UNIT is ROOF mounted, it is positioned a minimum 2100mm above the ground surface with a radial clearance of 600mm. Please ensure that the KLEENAIR unit is positioned in an environment that is free of other gases to enable an efcient expulsion of the cooking by-products and to ensure that back-draft of external gases doesn’t take place.

The unit can be mounted so that it ducts directly through the roof. Please ensure the fan motor is positioned away from other exhausts such as chimneys, gas fuses, etc. and that the top of the fan motor is mounted below the top of the roof line.

STEP 1:

Cut a 200mm diameter hole in the roof to enable the rigid duct on the base of the KLEENAIR unit to protrude down into the roof space. Please ensure that the hole is cut in a practical position to enable sufcient clearance around the fan motor unit. Afx the ashing (Optional Accessory HBX200TILE or HBX200MET) to the roof surface. Please ensure that the ashing is sealed thoroughly onto the rigid duct with silicone to prevent water leaks.

STEP 2:

Using standard 200mm pipe mounts (Optional Accessory HBX200TILE or HBX200MET), mount the rigid duct to beams, trusses or other appropriate structures in the roof space. Ensure the rigid duct protrudes past the top of the ashing by at least 75mm.

Max=150mm Min=75mm

STEP 3:

Remove the mounting bracket from your KLEENAIR unit by rotating the cover in an anti-clockwise direction.

STEP 4:

Fix the mounting bracket to the rigid duct using the screws provided.

STEP 5:

Feed the power cable through the centre of the mounting bracket and return the KLEENAIR unit on to the mounting bracket and x it by rotating the cover in a clockwise direction. Lock the cover into position by tightening the locking screw, which is located between the outlet and the mounting bracket.

STEP 6:

Attach the exi-duct to the rigid duct using the pipe clamps supplied.

STEP 7:

Attach exi-duct from the KLEENAIR unit to the rangehood using pipe clamps. Ensure that the duct is pulled tightly to ensure that exi-duct remains rm and stable during operation. Avoid sharp bends in the duct. Gentle bends in the ducting are recommended as it assists in mufing noise from the fan unit back to the rangehood. If the exi-duct needs to be extended, attach the two exi-duct ends using a rigid duct insert, secured by pipe clamps or duct tape. (Optional Accessory - HBX200DUCT)

STEP 8:

OPERATION

Operating your 4-button control panel

Models included: Electronic Control or Touch Control

TURNING THE EXTRACTION FUNCTION ON OR OFF:

• In standby mode, press button 2 or 3 to change the speed.

• The hood has three speed options and a 4th boost speed (4 speeds in total).

• The LED indicators directly above the buttons indicates the speed setting selected.

• To turn hood off, press button 2 repeatedly until hood returns to standby mode.

• Auto off function: After 2 hour of operation without alteration the fan motor will turn off (returned to standby).

TURNING THE LIGHT FUNCTION ON OR OFF:

Press button 1 to turn on or turn off the light independently in standby mode.

TURNING THE TIMER FUNCTION ON OR OFF:

In operating mode, press button 4 to engage the timer function, then press button 2 or 3 to adjust the delay time.

The default timer is set to 10mins and can be increased in increments of 10mins up to 1 hour (i.e. 4 pushes of button 3 will result in timer set to 50mins before shut off).

When the timer is rst activated, the LED positioned behind button 4 (timer) will ash quickly to indicate the time setting i.e. for 30mins remaining the LED will blink 3 times quickly. When the timer function is engaged the (timer) LED positioned behind button 4 (timer) will blink slowly until the timer expires.

1 2 3 4

PRODUCT CARE

It is recommended that your WHISPAIR rangehood and all of its items be cleaned regularly. Before any cleaning or maintenance work, disconnect the cooker hood from the mains power supply.

CLEANING THE STAINLESS STEEL HOOD UNIT

• It is expected that the stainless steel is cleaned with a quality non-abrasive stainless steel cleaner.

• Use a soft cloth for application.

• It is recommended that this is performed every 4 weeks.

CLEANING THE KLEENAIR FAN MOTOR UNIT

• The KLEENAIR unit should be checked regularly to ensure that nothing is obstructing the air ow from the housing.

• If there are obstructions, please remove the debris ensuring the product returns to the manufacturer’s intended operating condition.

CLEANING THE BAFFLE FILTERS AND GREASE TRAP

• The bafe lters and grease trap can be removed from the mounted position within the hood and washed in the dishwasher or by hand.

• Use hot water and liquid detergent.

• After cleaning, leave the lters and trap to dry before placing back in the hood.

WARNING WHEN CHANGING THE LED LAMP

Please be aware that whilst in use LED lighting units may become hot and the surrounding area may remain hot for some time after switching off. Please allow the lamp area to cool before operating near the lighting.

REPLACEMENT OF LED LAMP

• Make sure the main power supply into hood is disconnected at the GPO.

• Using a ne at blade, wedge the LED unit from the insert whilst applying pressure to the locking tab.

• Disconnect the 12V connectors.

• Replace with a new unit and push back inside the cut outs in the fascia.

• Please replace only with a genuine unit available from Haus Group Australia Pty Ltd.

WARRANTY

Every WHISPAIR rangehood comes with a 5-Year parts and labour warranty. This warranty is conditional upon the appliance being used only for personal, domestic and household purposes and installed and operated in accordance with WHISPAIR instructions.

The consumer is responsible for any charges associated with removal of the faulty unit and installation of the new unit.

The customer may also be responsible for any freight charges incurred in this change over process.

The installation of WHISPAIR rangehoods must comply with the information in the guide. Installation of the rangehood must be in a covered area, to avoid direct weathering. Failure to follow the guidelines will result in loss of warranty.

We recommend our customers use an authorised WHISPAIR installer.

Any imperfections in the nishes or in the natural materials used should not be considered as faults but a typical characteristic of these crafted products.

Should you ever need to make a warranty related enquiry about your WHISPAIR product, in Australia simply call Haus Group Australia on +61 (0) 3 8593 9600 or New Zealand on +64 (0) 9 887 6959 to speak with our friendly customer service team consultants. We suggest you have the following information close at hand to make the process as easy as possible:

1. Model number of your complete rangehood and motor unit

2. A copy of your WHISPAIR proforma invoice

3. Address details of where the appliance has been installed

Any associated or ancillary costs to be incurred by you as a result of replacement or repair of your WHISPAIR rangehood under this guarantee shall, in all cases, be previously approved by Haus Group Australia Pty Ltd.

Please note: The benets provided under this warranty are additional to other rights and remedies available to the customer under the Australian Customer Law.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or a refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

YOUR STATUTORY RIGHTS