Whirlpool YWED6400SW1, YWED6400SW0, YWED6200SW1, YWED6200SW0, WED6400SW1 Owner’s Manual

...

cabr o

FABRIC CARE SYSTEM

CABRIOTMFABRIC

CARESYSTEM

ELECTRICDRYER

For questions about features, operation/perlormance,

parts, accessories or service call: 1-800-253-130t

In Canada, call: 1-800-807-6777

www,whirlpool.eom or www.whirlpool,ca

SECADORAELECTRICA

CABRIOTMCON

SISTEMADECUIDADO

or visit our website at

DELAROPA

W10054070A

i_ J;, _ 1 _ _:.......

Si tiene preguntas respecte a las caraeteristicas, funeionamiento,

rendimiento, partes, aacesories e servicio tecnico, lame al:

1-800-253-130t

o visite nuestro sitio web en

www.whirlpool.com

SECHEUSE

ELECTRIQUE,CABRIOTM

AVECSYSTEMEDE

SOINDESTISSUS

" +' * I

Au Canada, pour assistance, installation ou service, composez le :

Table of Contents/Indice/Table des matieres ...... 2

1-800-807-6777

ou visitez notre site internet &

www.whirlpool.ca

TABLEOFCONTENTS

DRYER SAFETY .............................................................................. 3

INSTALLATION INSTRUCTIONS .................................................. 4

Tools and Parts ............................................................................ 4

Location Requirements ............................................................... 4

Electrical Requirements - U.S.A. Only ......................................... 5

Electrical Requirements - Canada Only ....................................... 6

Electrical Connection - U.S.A. Only ............................................. 7

Venting Requirements ................................................................ 12

Plan Vent System ....................................................................... 13

Install Vent System ..................................................................... 14

Install Leveling Legs ................................................................... 14

Connect Vent .............................................................................. 14

Level Dryer ................................................................................. 14

Reverse Door Swing .................................................................. 15

Complete Installation ................................................................. 16

DRYER USE .................................................................................. 17

Starting Your Dryer ..................................................................... 17

Stopping, Pausing or Restarting ................................................ 18

Drying and Cycle Tips ................................................................ 18

Status Lights .............................................................................. 18

Cycles ......................................................................................... 19

Modifiers ..................................................................................... 20

Options ....................................................................................... 20

End of Cycle Signal .................................................................... 21

Changing Cycles, Modifiers and Options .................................. 21

Drying Rack Option .................................................................... 21

DRYER CARE ............................................................................... 22

Cleaning the Dryer Location ...................................................... 22

Cleaning the Lint Screen ............................................................ 22

Cleaning the Dryer Interior ......................................................... 22

Removing Accumulated Lint ...................................................... 22

Vacation and Moving Care ......................................................... 23

Changing the Drum Light ........................................................... 23

TROUBLESHOOTING .................................................................. 23

ASSISTANCE OR SERVICE ......................................................... 25

WARRANTY .................................................................................. 26

INDICE

SEGURIDAD DE LA SECADORA ................................................ 28

INSTRUCCIONES DE INSTALACION ......................................... 29

Herramientas y piezas ................................................................ 29

Requisitos de ubicaci6n ............................................................ 29

Requisitos electricos - $61o en EE. UU..................................... 30

Conexi6n electrica - S61oen EE. UU......................................... 32

Requisitos de ventilaci6n ........................................................... 37

Planificacidn del sistema de ventilaci6n .................................... 38

Instalacidn del sistema de ventilaci6n ....................................... 39

Instalaci6n de las patas niveladoras .......................................... 40

Conexi6n del ducto de escape .................................................. 40

Nivelacidn de la secadora .......................................................... 40

C6mo invertir el cierre de la puerta ............................................ 41

Complete la instalacidn - EE. UU............................................... 42

USO DE LA SECADORA .............................................................. 43

Puesta en marcha de la secadora ............................................. 43

C6mo detener, pausar y volver a poner en marcha .................. 44

Sugerencias de ciclos y secado ................................................ 45

Luces de estado ......................................................................... 45

Ciclos .......................................................................................... 46

Modificadores ............................................................................ 47

Opciones .................................................................................... 47

Sehal de fin de ciclo (End of Cycle Signal) ................................ 48

Cambio de ciclos, modificadores y opciones ........................... 48

Opci6n de estante de secado .................................................... 48

CUIDADO DE LA SECADORA ..................................................... 49

Limpieza del lugar donde esta la secadora ............................... 49

Limpieza del filtro de pelusa ...................................................... 49

Limpieza del interior de la secadora .......................................... 50

Eliminaci6n de pelusa acumulada ............................................. 50

Cuidado durante las vacaciones y mudanzas ........................... 50

Cambio de la luz del tambor ...................................................... 50

SOLUCION DE PROBLEMAS ...................................................... 51

AYUDA O SERVICIO TECNICO ................................................... 53

GARANTIA ..................................................................................... 54

TABLEDESMATIERES

SI_CURIT¢: DE LA SI_CHEUSE .................................................... 55

INSTRUCTIONS D'INSTALLATION ............................................. 56

Outillage et pieces ...................................................................... 56

Exigences d'emplacement ......................................................... 56

Specifications electriques - Pour le Canada seulement ............ 57

Exigences concernant I'evacuation ........................................... 58

Planification du systeme d'evacuation ...................................... 59

Installation du systeme d'evacuation ......................................... 61

Installation des pieds de reglage de I'aplomb ........................... 61

Raccordement du conduit d'evacuation ................................... 61

Reglage de I'aplomb de la secheuse ......................................... 61

Inversion du sens d'ouverture de la porte ................................. 62

Achever I'installation .................................................................. 63

UTILISATION DE LA S¢:CHEUSE ................................................ 54

Mise en marche de la secheuse ................................................ 64

Arr_t, pause ou remise en marche ............................................. 65

Conseils pour le sechage et les programmes ........................... 65

Temoins lumineux ...................................................................... 66

Programmes ............................................................................... 66

Modificateurs .............................................................................. 67

Options ....................................................................................... 68

Signal de fin de programme ....................................................... 68

Changement des programmes, modificateurs et options .........69

Option de grille de sechage ....................................................... 69

ENTRETIEN DE LA S¢:CHEUSE .................................................. 70

Nettoyage de I'emplacement de la secheuse ........................... 70

Nettoyage du filtre a charpie ...................................................... 70

Nettoyage de I'interieur de la secheuse ..................................... 71

Retrait de la charpie accumulee ................................................ 71

Precautions h prendre pour les vacances et avant

un dem6nagement ..................................................................... 71

Changement de I'ampoule d'eclairage du tambour .................. 71

DI!:PANNAGE ................................................................................. 72

ASSISTANCE OU SERVICE ......................................................... 75

GARANTI E..................................................................................... 76

TODO LO OUE [14AGINAS"

DRYERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,

including the following:

[] Read all instructions before using the dryer. [] Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to

a chemical reaction that could cause a load to catch fire.

[] Do not dry articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry- cleaning solvents, or other flammable or explosive substances as they give off vapors that could ignite or

explode.

[] Do not allow children to play on or in the dryer. Close

supervision of children is necessary when the dryer is used near children.

[] Before the dryer is removed from service or discarded,

remove the door to the drying compartment. [] Do not reach into the dryer if the drum is moving. [] Do not install or store the dryer where it will be exposed

to the weather. [] Do not tamper with controls.

SAVE TH ESE iNSTRUCTiONS

[] Do not repair or replace any part of the dryer or attempt

any servicing unless specifically recommended in this Use and Care Guide or in published user-repair

instructions that you understand and have the skills to carry out.

[] Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric softener or product.

[] Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

[] Clean lint screen before or after each load. [] Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust, and dirt.

[] The interior of the dryer and exhaust vent should be

cleaned periodically by qualified service personnel.

[] See installation instructions for grounding requirements.

INSTALLATIONINSTRUCTIONS

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed

here.

• Flat-blade screwdriver • Tin snips (new vent

• #2 Phillips screwdriver installations)

• Adjustable wrench that • Level opens to 1" (2.5 cm) or • Vent clamps

hex-head socket wrench (for adjusting dryer feet) • Caulking gun and

• Wire stripper (direct wire new exhaust vent) installations) • Tape measure

Parts supplied:

Remove parts package from dryer drum. Check that all parts were included.

4 leveling legs

compound (for installing

• If you are using a power supply cord, a grounded electrical outlet located within 2 ft (61 cm) of either side of the dryer. See "Electrical Requirements."

• A sturdy floor to support the total weight (dryer and load) of 200 Ibs (90.7 kg). The combined weight of a companion appliance should also be considered.

• A level floor with a maximum slope of 1" (2.5 cm) under entire dryer.

Do not operate your dryer at temperatures below 45°F (7°C). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. Drying times can be extended.

The dryer must not be installed or stored in an area where it will be exposed to water and/or weather.

Check code requirements. Some codes limit, or do not permit, installation of the dryer in garages, closets, mobile homes or sleeping quarters. Contact your local building inspector.

Installation Clearances

The location must be large enough to allow the dryer door to open fully.

Dryer Dimensions

Parts needed:

Check local codes. Check existing electrical supply and venting and see "Electrical Requirements" and "Venting Requirements" before purchasing parts.

Mobile home installations require metal exhaust system hardware available for purchase from the dealer from whom you purchased

your dryer. For information on ordering, please refer to the

"Assistance or Service" section of this manual. You may also contact the dealer from whom you purchased your dryer.

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from dryer,

Place dryer at least 18 inches (46 cm) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

You will need

• A location that allows for proper exhaust installation. See "Venting Requirements."

• A separate 30-amp circuit.

431/2'

(110.5

!2¼"

*29¼"

(74.3 cm), 29"

(73.7 cm)

(56.5 cm)

*Most installations require a minimum 5" (12.7 cm) clearance

behind the dryer for the exhaust vent with elbow. See "Venting Requirements."

Installation spacing for recessed area or closet installation

The following spacing dimensions are recommended for this dryer. This dryer has been tested for spacing of 0" (0 cm) clearance on the sides and rear. Recommended spacing should be considered for the following reasons:

• Additional spacing should be considered for ease of installation and servicing.

• Additional clearances might be required for wall, door and floor moldings.

• Additional spacing should be considered on all sides of the dryer to reduce noise transfer.

For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.

• Companion appliance spacing should also be considered.

Additionalspacingisrequiredifyouexhaustouttherearof thedryertoeithertherightorleftside.

-NNNI_

A. Recessed area B. Side view - closet or confined area

C. Closet door with vents

*Required spacing

_f 3 'j*

_.6 cm)

(7.6cm)

Mobile home - Additional installation requirements This dryer is suitable for mobile home installations. The

installation must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280) or Standard CAN/CSA-Z240

MH.

Mobile home installations require:

• Metal exhaust system hardware, which is available for

purchase from your dealer. Special provisions must be made in mobile homes to

introduce outside air into the dryer. The opening (such as a nearby window) should be at least twice as large as the dryer exhaust opening.

It is your responsibility

• To contact aqualified electrical installer.

• To be sure that the electrical connection is adequate and in conformance with the National Electrical Code, ANSl/NFPA

70-latest edition and all local codes and ordinances. The National Electric Code requires a 4-wire power supply

connection for homes built after 1996, dryer circuits involved in remodeling after 1996, and all mobile home installations.

A copy of the above code standards can be obtained from: National Fire Protection Association, One Batterymarch Park, Quincy, MA 02269.

To supply the required 3 or 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt electrical supply, if specified on the serial/rating plate) on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Connect

to an individual branch circuit. Do not have a fuse in the neutral or grounding circuit.

• Do not use an extension cord.

• If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

Electrical Connection

To properly install your dryer, you must determine the type of

electrical connection you will be using and follow the instructions provided for it here.

• This dryer is manufactured ready to install with a 3-wire electrical supply connection. The neutral ground conductor is permanently connected to the neutral conductor (white wire) within the dryer. If the dryer is installed with a 4-wire electrical supply connection, the neutral ground conductor must be removed from the external ground connector (green screw), and secured under the neutral terminal (center or white wire) of the terminal block. When the neutral ground conductor is secured under the neutral terminal (center or white wire) of the terminal block, the dryer cabinet is isolated from the

neutral conductor.

• If local codes do not permit the connection of a neutral ground wire to the neutral wire, see "Optional 3-wire connection" in "Electrical Connection - U.S.A. Only" section.

A 4-wire power supply connection must be used when the appliance is installed in a location where grounding through the neutral conductor is prohibited. Grounding through the neutral is prohibited for (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral

conductors.

If using a power supply cord: Use a UL listed power supply cord kit marked for use with

clothes dryers. The kit should contain:

• A UL listed 30-amp power supply cord, rated 120/240 volt minimum. The cord should be type SRD or SRDT and be at least 4 ft (1.22 m) long, The wires that connect to the dryer must end in ring terminals or spade terminals with upturned

ends.

• A UL listed strain relief.

If your outlet looks like this:

4-wire receptacle (14-30R)

Then choose a 4-wire power supply cord with ring or spade terminals and UL listed strain relief. The 4-wire power supply cord, at least 4 ft (1.22 m) long, must have four 10-gauge copper wires and match a 4-wire receptacle of NEMA Type 14-30R. The ground wire (ground conductor) may be either green or bare. The neutral conductor must be identified by a white cover.

If your outlet looks like this:

3-wire receptacle (10-30R)

Then choose a 3-wire power supply cord with ring or spade terminals and UL listed strain relief. The 3-wire power supply cord, at least 4 ft (1.22 m) long, must have three 10-gauge copper wires and match a 3-wire receptacle of NEMA Type 10-30R.

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire) and be:

[] Flexible armored cable or nonmetallic sheathed copper cable

(with ground wire), protected with flexible metallic conduit. All

current-carrying wires must be insulated. [] 10-gauge solid copper wire (do not use aluminum). [] At least 5 ft (1.52 m) long.

GROUNDING INSTRUCTIONS

[] For a grounded, cord-connected dryer: This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This dryer uses a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

[] For a permanently connected dryer: This dryer must be connected to a grounded metal, permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the dryer.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is properly grounded. Do not modify the plug on the power supply cord: if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

To supply the required 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical supply on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or

circuit breaker is recommended. Connect to an individual branch circuit.

This dryer is equipped with a CSA International Certified Power Cord intended to be plugged into a standard 14-30R wall receptacle. The cord is 5 ft (1.52 m) in length. Be sure wall receptacle is within reach of dryer's final location.

4-wire receptacle 14-30R

[] Do not use an extension cord. If you are using a replacement power supply cord, it is

recommended that you use Power Supply Cord Replacement Part Number 3394208. For further information, please reference the service numbers located in the "Assistance or Service"

section of this manual.

GROUNDING INSTRUCTIONS

[] For a grounded, cord-connected dryer: This dryer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current. This dryer is equipped with a cord having an equipment- grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes and ordinances.

WARNING: Improper connection of the equipment- grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is properly grounded. Do not modify the plug provided with the dryer: if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

Electrical Shock Hazard

Plug into a grounded 4 prong outlet, Failure to do so can result in death or electrical shock.

It is your responsibility

[] To contact a qualified electrical installer. [] To be sure that the electrical connection is adequate and in

conformance with the Canadian Electrical Code, C22.1 -latest

edition and all local codes. A copy of the above codes

standard may be obtained from: Canadian Standards

Association, 178 Rexdale Blvd., Toronto, ON M9W 1R3

CANADA.

i_¸ , _:_,__ _,_ x •_•,_, ,,_ T _¸_i

Power Supply Cord

Fire Hazard

Use a new UL listed 30 amp power supply cord. Use a UL listed strain relief.

Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center

terminal (silver).

Ground wire (green or bare wire) must be connected to green ground connector.

Connect remaining 2 supply wires to remaining 2 terminals (gold).

Securely tighten all electrical connections. Failure to de so can result in death, fire, or

electrical shock.

Direct Wire

Fire Hazard

Use 10 gauge solid copper wire. Use a UL listed strain relief.

Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center

terminal (silver).

Ground wire (green or bare wire) must be connected to green ground connector.

Connect remaining 2 supply wires to remaining 2 terminals (gold).

Securely tighten all electrical connections.

Failure to do so can result in death, fire, or

electrical shock.

1. Disconnect power. 3. Install strain relief.

2. Remove the hold-down screw and terminal block cover. Style 1: Power supply cord strain relief

C D

Remove the screws from a 3/4"(1.9 cm) UL listed strain relief (UL marking on strain relief). Put the tabs of the two clamp sections into the hole below the terminal block opening so that one tab is pointing up and the other is pointing down, and hold in place. Tighten strain relief screws just enough to hold the two clamp sections together•

A. Terminal block cover B. Hold-down screw

C. External ground conductor screw D. Center, silver-colored terminal block screw

E.Neutral ground wire F. Hole below terminal block opening

A. Strain relief tab pointing up

B. Hole below terminal block opening C. Clamp section D. Strain relief tab pointing down

Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Do not further tighten strain relief screws at this point.

Style 2: Direct wire strain relief

Unscrew the removable conduit connector and any screws from a %" (1.9 cm) UL listed strain relief (UL marking on strain relief). Put the threaded section of the strain relief through the hole below the terminal block opening. Reaching inside the terminal block opening, screw the removable conduit

connector onto the strain relief threads.

Electrical Connection Options

If your home has: And you will be Go to Section:

connecting to:

4-wire receptacle A UL listed, 4-wire connection: (NEMA type 14-30R) 120/240-volt Power Supply Cord

30-amp, dryer

(_ minimum,

power supply cord*

4-wire direct A fused 4-wire connection:

disconnect or Direct Wire circuit breakerbox*

(12.7 cm)

3-wire receptacle A UL listed, (NEMA type 10-30R) 120/240-volt

3-wire connection:

Power Supply Cord

30-amp, dryer power supply

minimum, cord*

3-wire direct A fused 3-wire connection:

disconnect or Direct Wire box*

circuit breaker

............................B

..............................C

A. Removable conduit connector B. Hole below terminal block opening

C. Strain relief threads

Put direct wire cable through the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Tighten strain relief screw against the

direct wire cable.

*If local codes do not permit the connection of a cabinet-ground

conductor to the neutral wire, go to "Optional 3-wire connection" section.

4-wire connection: Power supply cord

IMPORTANT: A 4-wire connection is required for mobile homes

and where local codes do not permit the use of 3-wire connections.

B F

C D E G

A. 4-wire receptacle (NEMA type 14-30R) B. 4-prong plug C. Ground prong D. Neutral prong

E.Spade terminals with upturned ends F. _" (1.9 cm) UL Iisted strain relief

G. Ring terminals

Now complete installation following instructions for your type of electrical connection:

4-wire (recommended) 3-wire (if 4-wire is not available

Remove center silver-colored terminal block screw.

Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and the neutral wire (white or center wire) of power supply cord under center, silver-colored terminal block screw. Tighten screw.

A. Neutral ground wire B. External ground conductor screw - Dotted line shows

position of NEUTRAL ground wire before being moved to center silver-colored terminal block screw.

C. Center silver-colored terminal block screw D. Neutral wire (white or center wire)

E.3/4"(1.9 cm) UL listed strain relief

Connect ground wire (green or bare) of power supply cord to external ground conductor screw. Tighten screw.

5. Tighten strain relief screws.

6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

7. You have completed your electrical connection. Now go to "Venting Requirements."

4-wire connection: Direct Wire

IMPORTANT: A 4-wire connection is required for mobile homes

and where local codes do not permit the use of 3 wire connections.

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer

can be moved if needed. Strip 5" (12.7 cm) of outer covering from end of cable, leaving

bare ground wire at 5" (12.7 cm). Cut 11/2"(3.8 cm) from 3 remaining wires. Strip insulation back 1" (2.5 cm). Shape ends

of wires into a hook shape.

When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right),

squeeze hooked end together and tighten screw, as shown.

A. External ground conductor screw B. Neutral ground wire C. Ground wire (green or bare) of power supply cord D. 3/_,,(1.9 cm) UL Iisted strain relief

E.Center silver-colored terminal block screw

F Neutral wire (white or center wire)

Connect the other wires to outer terminal block screws. Tighten screws.

!! !!

Remove center silver-colored terminal block screw.

Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and place the hooked end (hook facing right) of the neutral wire (white or center wire) of direct wire cable under the center screw of the terminal block. Squeeze hooked ends together. Tighten

screw.

A. Neutral ground wire B. External ground conductor screw - Dotted line shows

position of NEUTRAL ground wire before being moved to center silver-colored terminal block screw.

C. Center silver-colored terminal block screw D. Neutral wire (white or center wire)

E.3_,,(1.9 cm) UL listed strain relief

3. Connect ground wire (green or bare) of direct wire cable to external ground conductor screw. Tighten screw.

Loosen or remove center silver-colored terminal block screw.

Connect neutral wire (white or center wire) of power supply cord to the center, silver-colored terminal screw of the terminal block. Tighten screw.

................i .........................C

A. External ground conductor screw

B. Neutral ground wire C. Ground wire (green or bare) of power supply cord D. 3_,, (1.9 cm) UL listed strain relief

E. Center silver-colored terminal block screw

F Neutral wire (white or center wire)

4. Place the hooked ends of the other direct wire cable wires under the outer terminal block screws (hooks facing right).

Squeeze hooked ends together. Tighten screws.

!! !!

5. Tighten strain relief screw.

6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

7. You have completed your electrical connection. Now go to "Venting Requirements."

3-wire connection: Power supply cord

Use where local codes permit connecting cabinet-ground conductor to neutral wire.

A. External ground conductor screw B. Neutral ground wire

C. Center silver-colored terminal block screw D. Neutral wire (white or center wire)

E. _" (1.9 cm) UL listed strain relief

3. Connect the other wires to outer terminal block screws. Tighten screws.

!! !!

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

6. You have completed your electrical connection. Now go to "Venting Requirements,"

3-wire connection: Direct Wire

Use where local codes permit connecting cabinet-ground conductor to neutral wire.

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer can be moved if needed.

Strip 31/2'' (8.9 cm) of outer covering from end of cable. Strip insulation back 1" (2.5 cm). If using 3-wire cable with ground wire, cut bare wire even with outer covering, Shape ends of wires into a hook shape.

C G F

A. 3-wire receptacle (NEMA type 10-30R) B. 3-wire plug C. Neutral prong D. Spade terminals with upturned ends

E. _" (1.9 cm) UL listed strain relief F. Ring terminals

G. Neutral wire (white or center wire)

When connecting to the terminal block, place the hooked end of

the wire under the screw of the terminal block (hook facing right),

squeeze hooked end together and tighten screw, as shown.

Loosen or remove center silver-colored terminal block screw.

Place the hooked end of the neutral wire (white or center wire) of direct wire cable under the center screw of terminal block

(hook facing right). Squeeze hooked end together. Tighten screw.

Optional 3-wire connection

Use for direct wire or power supply cord where local codes do not permit connecting cabinet-ground conductor to neutral wire.

1. Remove center silver-colored terminal block screw.

2. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and the neutral wire (white or center wire) of power supply cord/cable under center, silver-colored terminal block screw. Tighten screw.

A. External ground conductor screw

B. Neutral ground wire C. Center silver-colored terminal block screw

D. Neutral wire (white or center wire)

E. _" (1.9 cm) UL listed strain relief

Place the hooked ends of the other direct wire cable wires under the outer terminal block screws (hooks facing right).

Squeeze hooked ends together. Tighten screws.

!! !!

4. Tighten strain relief screw.

5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

You have completed your electrical connection. Now go to "Venting Requirements."

A. External ground conductor screw

B. Neutral ground wire C. Center silver-colored terminal block screw

D. Neutral wire (white or center wire)

E. _" (1.9 cm) UL Iisted strain relief

E Grounding path determined by a qualified electrician

Connect the other wires to outer terminal block screws. Tighten screws.

!! !!

__m__

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

6. Connect a separate copper ground wire from the external ground conductor screw to an adequate ground.

Fire Hazard

Use a heavy metal vent. Do not use a plastic vent.

Do not use a metal foil vent. Failure to fellow these instructions can result in death

or fire.

• Remove excess flexible metal vent to avoid sagging and kinking that may result in reduced airflow and poor performance.

• Do not install flexible metal vent in enclosed walls, ceilings or floors.

Elbows

45° elbows provide better airflow than 90° elbows.

Good Better

WARNING: To reduce the risk of fire, this dryer MUST BE

EXHAUSTED OUTDOORS. IMPORTANT: Observe all governing codes and ordinances.

The dryer exhaust must not be connected into any gas vent,

chimney, wall, ceiling or a concealed space of a building.

If using an existing vent system

• Clean lint from the entire length of the system and make sure exhaust hood is not plugged with lint.

• Replace any plastic or metal foil vent with rigid or flexible heavy metal vent.

• Review Vent system chart. Modify existing vent system if necessary to achieve the best drying performance.

If this is a new vent system

Vent material

• Use a heavy metal vent. Do not use plastic or metal foil vent.

• 4" (10.2 cm) heavy metal exhaust vent and clamps must be used. DURASAFE TM venting products are recommended.

Clamps

Use clamps to seal all joints. Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into the interior of the duct. Do not use duct tape.

Clamp

Exhaust

Recommended hood styles are shown here.

(10.2 cm)

A. Louveredhood style

B.Box hood style

The angled hood style (shown here) is acceptable.

4-"

4" (10.2cm) heavymetal exhaust vent

DURASAFE TM vent products can be purchased from your dealer or by calling Whirlpool Parts and Accessories. For

more information, see the "Assistance or Service" section of this manual.

Rigid metal vent

• For best drying performance, rigid metal vents are recommended.

• Rigid metal vent is recommended to avoid crushing and kinking.

Flexible metal vent

• Flexible metal vents are acceptable only if accessible for cleaning.

• Flexible metal vent must be fully extended and supported when the dryer is in its final location.

(10.2 cm}__

_'_,_ 21/2"

(6.4- cm)

• An exhaust hood should cap the vent to keep rodents and insects from entering the home.

• Exhaust hood must be at least 12" (30.5 cm) from the ground or any object that may be in the path of the exhaust (such as

flowers, rocks or bushes, snow line, etc.).

• Do not use an exhaust hood with a magnetic latch.

improper venting can cause moisture and lint to collect indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint, wallpaper,

carpets, etc.

[] Housecleaning problems and health problems.

Chooseyourexhaustinstallationtype

Recommendedexhaustinstallations

Typical installations vent the dryer from the rear of the dryer.

A ¸-

.-- m

A. Dryer E. Clamps B. Elbow F. Rigid metal or flexible metal vent

C. Wall G, Vent length necessary to connect D. Exhaust hood elbows

H. Exhaust outlet

Standard exhaust installation with rigid metal or flexible metal vent

NOTE: The following kits for close clearance alternate installations are available for purchase. Please see the

"Assistance or Service" section of this manual to order.

• Over-the-Top Installation: Part Number 4396028

• Periscope Installation (For use with dryer vent to wall vent mismatch):

Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm) mismatch Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm)

mismatch Part Number 4396014 - 29" (73.66 cm) to 50" (127 cm)

mismatch

• Rear exhaust installation to left or right side: Part Number 8212504

Special provisions for mobile home installations The exhaust vent must be securely fastened to a noncombustible

portion of the mobile home structure and must not terminate beneath the mobile home. Terminate the exhaust vent outside.

Alternate installations for close clearances Venting systems come in many varieties. Select the type best for

your installation. Two close-clearance installations are shown.

Refer to the manufacturer's instructions.

-.q...

B C

A. Over-the-top installation (also available with one

offset elbow)

B. Periscope installation C. Rear exhaust installation to left or right side

Determine vent path

• Select the route that will provide the straightest and most direct path outdoors.

• Plan the installation to use the fewest number of elbows and turns.

• When using elbows or making turns, allow as much room as possible.

• Bend vent gradually to avoid kinking.

• Use the fewest 90° turns possible.

Determine vent length and elbows needed for best drying performance

• Use the following Vent system chart to determine type of vent material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified in the Vent system chart. Exhaust systems longer than those specified will:

• Shorten the life of the dryer.

• Reduce performance, resulting in longer drying times and

increased energy usage.

The Vent system chart provides venting requirements that will help to achieve the best drying performance.

Vent system chart

NOTE: Performance of rear exhaust to either side of the dryer is equivalent to adding one elbow. To determine maximum exhaust length, add one elbow to the chart.

Number of Type of Box or Angled

90° turns vent Louvered hoods

or elbows hoods

0 Rigid metal 64 ft (20 m) 58 ft (17,7 m)

Flexible metal 36 ft (11 m) 28 ft (8,5 m)

1 Rigid metal 54 ft (16.5 m) 48 ft (14.6 m)

Flexible metal 31 ft (9.4 m) 23 ft (7 m)

2 Rigid metal 44 ft (13.4 m) 38 ft (11,6 m)

Flexible metal 27 ft (8,2 m) 19 ft (5,8 m)

3 Rigid metal 35 ft (10.7 m) 29 ft (8.8 m)

Flexible metal 25 ft (7,6 m) 17 ft (5,2 m)

4 Rigid metal 27 ft (8,2 m) 21 ft (6,4 m)

Flexible metal 23 ft (7 m) 15 ft (4,6 m)

1. Install exhaust hood. Use caulking compound to seal exterior wall opening around exhaust hood.

2. Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.

3. Run vent to dryer location. Use the straightest path possible. See "Determine vent path" in "Plan Vent System." Avoid 90° turns. Use clamps to seal all joints. Do not use duct tape, screws or other fastening devices that extend into the interior

of the vent to secure vent.

Examine the leveling legs. Find the diamond marking.

4. Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs until the diamond marking is no longer

visible.

5. Place a carton corner post from dryer packaging under each of the 2 dryer back corners. Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location. Leave enough room to connect the exhaust vent.

1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure the vent is

clean. The dryer vent must fit over the dryer exhaust outlet and inside the exhaust hood. Check that the vent is secured

to exhaust hood with a 4" (10.2 cm) clamp.

2. Move dryer into its final location. Do not crush or kink vent.

3. (On gas models) Check that there are no kinks in the flexible gas line.

4. Once the exhaust vent connection is made, remove the corner posts and cardboard.

Check the levelness of the dryer by first placing a level on the top of the dryer near the console.

Excessive Weight Hazard

Use two or more people to move and install dryer. Failure to do so can result in back or other injury.

1. To protect the floor, use a large, flat piece of cardboard from the dryer carton. Place cardboard under the entire back edge of the dryer.

2. Firmly grasp the body of the dryer (not the top or console panel). Gently lay the dryer on the cardboard. See illustration.

Then, by placing a level in the crease on the side of the dryer between the top of the dryer and the dryer cabinet, check the

levelness from front to back.

If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs up or down and check again for

levelness.

You can change your door swing from a right-side opening to a left-side opening, if desired.

1. Place a towel or soft cloth on top of the dryer or work space to protect the surface.

Remove the door assembly

1. Open the dryer door.

2. Remove the bottom screw from each of the 2 hinges that attach the dryer door to the front panel of the dryer.

3. Loosen the top screw from each of the 2 hinges in Step 2.

A B

-B

A. Loosen these screws. B. Remove these screws.

Reverse the strike

1. Remove the door strike from the dryer door opening.

2. Remove the cosmetic screw opposite the door strike.

A. Door strike B. Cosmetic screw

3. Reinstall the door strike and cosmetic screw on the opposite side of the dryer door opening from where they were

removed. NOTE: Door strike and plugs must be on the same side of the

dryer door opening.

Reinstall the door

1. Remove the 4 screws and 2 hinges from the dryer door.

2. Replace the 4 screws in the same holes.

4. Remove the dryer door and the hinges by lifting upward on the door. Lay the door on a flat, protected surface, with the inside of the door facing up. Remove remaining 2 loose screws from dryer front panel.

5. Remove the 4 plastic plugs located outside the dryer door opening.

Install 4 plastic plugs into screw holes in the dryer left where the hinges were removed in Step 4.

3. Remove the 4 screws from the opposite side of the door.

4. Install the 2 hinges to the front panel of the dryer using 4 screws. Use the non-slotted side to attach the hinge to the front panel.

5. Install screws in the top hinge holes in the door. Do not tighten screws. Leave approximately 1A" (5 mm) of screw exposed.

A. Install these screws first.

Hang door by placing screw heads into top slotted holes of hinges and slide door down. Align bottom screw holes in hinge and door. Install two bottom screws. Tighten all hinge

screws.

]

7. Close door to engage door strike.

1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check the dryer's final location. Be sure the vent is not crushed or kinked.

5. Check that the dryer is level. See "Level Dryer."

6. In the U.S.A.

• For power supply cord installation, plug into a grounded

outlet. For direct wire installation, turn on power.

In Canada

• Plug into a grounded 4 prong outlet. Turn on power.

7. Remove any protective film or tape remaining on the dryer. NOTE: Glass door models have a protective film on the

window that should be removed.

8. Read "Dryer Use."

9. Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust.

10. Test dryer operation by selecting a Timed Dry heated cycle and starting the dryer. For this test, do not select the Air Only

modifier. If the dryer will not start, check the following:

• Controls are set in a running or "On" position.

• Start button has been pushed firmly.

• Dryer is plugged into an outlet and/or electrical supply

is on.

• Household fuse is intact and tight, or circuit breaker has

not tripped.

• Dryer door is closed.

11. When the dryer has been running for 5 minutes, open the dryer door and feel for heat. If you feel heat, cancel cycle and

close the door.

If you do not feel heat, turn off the dryer and check the

following:

• There may be 2 household fuses or circuit breakers for

the dryer. Check that both fuses are intact and tight, or that both circuit breakers have not tripped. If there is still no heat, contact a qualified technician.

NOTE: You may notice an odor when the dryer is first heated. This odor is common when the heating element is first used. The odor will go away.

DRYERUSE

TIMED QUICK TOuUpCH

DRY DRY

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from dryer.

Do not dry anything that has ever had anything

flammable on it (even after washing).

Failure to follow these instructions can result in death,

explosion, or fire.

WARNING: To reduce the risk of fire, electric shock, or injury to To use an Automatic Cycle

persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance. •

This manual covers several different models. Your dryer may not •

have all of the cycles and features described. • Follow these basic steps to start your dryer. Please refer to

specific sections of this manual for more detailed information.

1. Clean lint screen before each load. See "Cleaning the Lint Screen."

2. Place laundry into dryer and shut door.

3. Press POWER.

4. Turn the knob to the selected cycle. The preset settings for Automatic Cycles or Timed Cycles will illuminate. The estimated (automatic cycle) or actual (timed) cycle time (in •

minutes) will show in the display. To NOTE: A default time is displayed when an automatic cycle is selected. During the first few minutes of the drying process, • the cycle time may automatically vary from the default time based on the size and fabric type of the load. Toward the end of the drying process, the estimated time display will adjust again, showing the final drying time.

No washer can completely remove oil. Do not dry anything that has ever had any type of oil on

it (including cooking oils).

Items containing foam, rubber, or plastic must be dried on a clothesline or by using an Air Cycle.

Failure to follow these instructions can result in death or fire.

Press POWER. Turn the knob to desired Automatic Cycle.

Select DRYNESS to adjust how dry you want the load. As the cycle runs, the control senses the dryness of the load and adjusts the time automatically for the selected dryness level.

The default dryness setting is Normal when an Automatic Cycle is selected. You can select a different dryness level, depending on your load, by pressing Dryness and choosing More, Less or Damp. Selecting More, Less or Damp automatically adjusts the sensed time needed. Once a dryness level is set, it cannot be changed without stopping the cycle.

Select the desired Options.

make changes during an Automatic Cycle:

Press PAUSE/CANCEL

Fire Hazard

• Adjust Dryness.

DRYNESS

NOTE: Dryness selections can be made only while using Automatic Cycles.

How the AccelerCare TM Drying System Works Moisture-sensing strips inside the dryer drum and

temperature sensors in the airstream monitor how fast the load is drying, how hot the air should be and when clothes

are dry. The system automatically stops the cycle to help save time and avoid overdrying.

To use a Timed Cycle

Turn knob to desired Timed Cycle. Press the TIME ADJUST up or down arrows until the

desired drying time is displayed. Press the up or down arrows and the time will change by 1-minute intervals.

Press and hold the up or down arrows and the time will change by 5-minute intervals.

NOTE: The Time Adjust features can be used only with Timed Cycles.

TIMEADJUST

• Press TEMP until the desired temperature illuminates.

TEMP

NOTE: The Temp feature can be used only with Timed Cycles.

NOTE: During a Timed Cycle, you can change the settings for Time, Temp, the WRINKLE SHIELD TM setting and the End of Cycle Signal.

5. (OPTIONAL STEP) If desired, select OPTIONS. For more details, see "Options."

6. (OPTIONAL STEP) If desired, press END OF CYCLE SIGNAL. A signal will sound to alert you when a cycle ends. For more

details, see "End of Cycle Signal."

7. Press START. Be sure the door is closed.

• If you do not press Start within 5 minutes of selecting the

cycle, the dryer automatically shuts off.

• If you wish to end your drying cycle after pressing Start,

press PAUSE/CANCEL twice.

Select the correct cycle and dryness level or temperature for your load. If an Automatic Cycle is running, the display shows the estimated cycle time when your dryer is automatically sensing the dryness level of your load. If a Timed Cycle is running, the display shows the exact number of minutes remaining in the cycle.

Cool Down tumbles the load without heat during the last few minutes of all cycles. Cool Down makes the loads easier to handle and reduces wrinkling. The length of the Cool Down depends on the load size and dryness level.

Drying tips

• Follow care label directions when they are available.

• If desired, add a fabric softener sheet. Follow package instructions.

• To reduce wrinkling, remove the load from the dryer as soon as tumbling stops. This is especially important for permanent press, knits and synthetic fabrics.

• Avoid drying heavy work clothes together with lighter fabrics. This could cause overdrying of lighter fabrics and lead to increased shrinkage or wrinkling.

Cycle tips

• Dry most loads using the preset cycle settings.

• Refer to the Automatic or Timed Preset Cycle Settings chart (in the "Cycles" section) for a guide to drying various loads.

• Drying temperature and dryness level are preset when

you choose an Automatic Cycle. You can select a different dryness level, depending on your load, by pressing Dryness and choosing More, Normal, Less or Damp.

NOTE: You cannot use the Time Adjust and you cannot choose a Temperature with the Automatic Cycles.

• If you wish to adjust the cycle length of a Timed Cycle,

press the Time Adjust up or down arrows. Adjust the temperature of a Timed Cycle by pressing Temp until the desired temperature is selected.

NOTE: You cannot choose a dryness level with Timed Cycles.

Follow the progress of your dryer with the drying Status indicator lights.

Cool Wrinkle

Sensing

• In an Automatic Cycle, the Sensing light illuminates until a wet item is detected.

• In a Timed Cycle, the Sensing light illuminates at the beginning of a cycle and turns off 5 minutes into the cycle.

To stop or pause your dryer at any time Open the door or press PAUSE/CANCEL once. Press PAUSE/ CANCEL twice to cancel a cycle.

To restart the dryer

Close the door. Press START until dryer starts. NOTE: Drying will continue from where the cycle was interrupted

if you close the door and press Start within 5 minutes. Ifthe cycle is interrupted for more than 5 minutes, the dryer will shut off.

Select new cycle settings before restarting the dryer.

Wet

The Wet light illuminates at the beginning of an Automatic Cycle if a wet item is detected.

• In an Automatic Cycle, if a wet item is not detected after approximately 5 minutes, the dryer goes directly into Cool

Down and the Cool Down and the WRINKLE SHIELD TM setting indicators illuminate, if selected.

• In a Timed Cycle, wet items are not detected. The dryer will continue to run for the length of time selected, and the Wet light will illuminate. The damp light will not illuminate.

Damp

The Damp light illuminates in an Automatic Cycle when the

laundry is approximately 80% dry. Damp Dry Signal beeps, if selected. See "Options."

Cool Down

The Cool Down light illuminates during the cool down part of the

cycle. Laundry cools for ease in handling.

Done

The Done light illuminates when the drying cycle is finished. This

indicator stays on during the WRINKLE SHIELD TM setting.

WRINKLE SHIELD TM Setting

The WRINKLE SHIELD TM setting light illuminates when this

option is selected. This indicator stays on during the WRINKLE SHIELD TM setting.

Indicator lights Other indicator lights show Cycle, Modifiers, Options and Cycle

Signal settings selected. The display shows the estimated or actual time remaining.

Select the drying cycle that matches the type of load you are drying. See Automatic or Timed Preset Cycle Settings charts.

CASUAL

DELICATE

Automatic Preset Cycle Settings Automatic Cycles Temperature

Load Type HEAVY DUTY High

Heavyweight mixed loads, cottons,

jeans

NORMAL Medium

Corduroys, work clothes

CASUAL Low

Business casual clothes, permanent press, synthetics

DELICATE Extra-Low Lingerie, blouses, washable knit

fabrics

Timed Cycles

Use Timed Cycles to select a specific amount of drying time and a drying temperature. When a Timed Cycle is selected, the Estimated Time Remaining display shows the actual time remaining in your cycle. You can change the actual time in the cycle by pressing the Time Adjust up or down arrows. See "Changing Cycles, Modifiers and Options."

NOTE: Timed Cycles may also be used with the dryer rack. See "Dryer Rack."

TIMED

DRY QUICK TOUCH

DRY UP

Automatic Cycles

Automatic Cycles allow you to match the cycle to the load you

are drying. See the following Automatic Preset Cycle Settings chart. Each cycle dries certain fabrics at the recommended

temperature. A sensor detects the moisture in the load and

automatically adjusts the drying time for optimal drying.

Heavy Duty

Use this cycle to get high heat for heavyweight mixed loads, cottons and jeans.

Normal

Use this cycle to get medium heat for drying sturdy fabrics such as work clothes.

Casual

Use this cycle to get low heat for drying no-iron fabrics, such as sport shirts, casual business clothes and permanent press

blends.

Timed Dry

Use this cycle to complete drying if items are still damp after an Automatic Cycle. Timed Dry is also useful for drying heavyweight and bulky items, such as bedspreads and work clothes.

Lightweight garments, such as exercise wear, can be dried using Timed Dry on a low temperature setting.

QUICK DRY

Use this cycle for drying small loads or loads that need a short drying time.

Touch Up

Use this cycle to help smooth out wrinkles from such items as clothes packed in a suitcase or items wrinkled from being left in the dryer too long.

Timed Preset Cycle Settings Timed Cycles Default Default Time

Load Type Temperature (Minutes) TIMED DRY High 40

Heavyweight, bulky items, work clothes

QUICK DRY Medium 24 Small loads

TOUCH UP Medium 20 Helps to smooth out

wrinkles

Delicate

Use this cycle to get extra-low heat to gently dry items such as lingerie, blouses or washable knit fabrics.

Automatic Cycle Modifiers

Use the Dryness Modifier to select dryness levels for the Auto Dry Cycles. Press DRYNESS until the desired Dryness setting

illuminates.

The preset dryness setting is Normal when an Automatic Cycle is

selected. You can select a different dryness level, depending on

your load, by pressing Dryness and choosing More, Normal, Less

or Damp. Selecting More, Normal, Less or Damp automatically adjusts the dryness level at which the dryer will shut off. Once a dryness level is set, it cannot be changed without stopping the cycle.

DRYNESS

NOTE: Dryness Level selections cannot be used with the Timed Cycles.

Timed Cycle Modifiers

Use the Temperature Modifier to select temperatures for the

Timed Cycles. Press TEMP until the desired temperature setting

illuminates.

TEMP

NOTE: Temperature modifiers cannot be used with the Auto Dry Cycles.

Air Only

Use the Air Only Modifier for items that require drying without heat such as rubber, plastic and heat-sensitive fabrics. This table shows examples of items that can be dried using Air Only.

Type of Load Time*

(Minutes)

Foam rubber - pillows, padded bras, stuffed toys 20 - 30 Plastic - Shower curtains, tablecloths 20 - 30 Rubber-backed rugs 40 - 50 Olefin, polypropylene, sheer nylon 10 - 20

*Reset cycle to complete drying, if needed.

When using Air Only

• Check that coverings are securely stitched.

• Shake and fluff pillows by hand periodically during the cycle.

• Dry item completely. Foam rubber pillows are slow to dry. NOTE: Air Only is not available with Automatic Cycles.

You can customize your cycles by selecting options.

"V"

DRUM LIGHT

WRINKLESHELD

DAMP DRY

SIGNAL

OPTIONS

Drum Light

On some models, select Drum Light to turn on the light inside the dryer drum. During a cycle, if Drum Light is selected, the drum light turns on and will remain on until DRUM LIGHT is pressed again, the door is opened and closed, or the door is left open for

5 minutes. When the dryer is not running, the drum light will turn on when

DRUM LIGHT is pressed or the dryer door is opened, and it will remain on until the dryer door has been open for 5 minutes, the dryer door is closed or DRUM LIGHT is pressed again.

Press DRUM LIGHT at any time to turn the drum light ON or OFR

WRINKLE SHIELD TM Setting

The WRINKLE SHIELD TM setting helps keep wrinkles from forming when you cannot unload the dryer promptly at the end of a cycle. During this option, the dryer stops tumbling and then tumbles again for a brief period.

• Press the WRINKLE SHIELD TM setting to get up to 120 minutes of heat-free, periodic tumbling at the end of a cycle.

• Stop the WRINKLE SHIELD TM setting at any time by pressing WRINKLE SHIELD TM setting or opening the dryer door.

For the Perm Press/Casual Cycle, the WRINKLE SHIELD TM setting is preset to ON. The other Automatic Cycles will retain the WRINKLE SHIELD TM setting. For example, if you select the WRINKLE SHIELD TM setting in the Normal cycle, the WRINKLE SHIELD TM setting will be on the next time you select the Normal cycle.

NOTE: If you do not select the WRINKLE SHIELD TM setting, the dryer stops after cool down.

Damp Dry Signal

Select the Damp Dry Signal to alert you that your clothes are approximately 80% dry. This is useful when you want to remove lightweight items in a mixed load to avoid overdrying or remove partially dry items that may need ironing.

The Damp Dry Signal is useful when drying bedsheets/linens in a mixed load. When the signal goes off, open the door to stop the dryer, rearrange the load inside the dryer, close the door and restart the dryer to finish the drying cycle. Rearranging the load will aid in the drying process.

NOTE: The Damp Dry Signal is available only with the Automatic Cycles.

End of Cycle Signal

The End of Cycle Signal produces an audible sound when the

drying cycle is finished. Promptly removing clothes at the end of

the cycle reduces wrinkling.

Press END OF CYCLE SIGNAL until the desired volume (Loud, Soft or Off) is selected.

[0_d Soft Off

((4*b))

ENDOf CYCLE

SIGNAL

NOTE: When the WRINKLE SHIELD TM setting is selected and the End of Cycle Signal is on, a tone sounds every 5 minutes until the clothes are removed, or the WRINKLE SHIELD TM setting ends.

You can change Automatic and Timed Cycles, Modifiers and Options anytime before pressing Start.

• Three short tones sound if an unavailable combination is selected. The last selection will not be accepted.

Changing Cycles after pressing Start

1. Press PAUSE/CANCEL twice.

2. Select the desired cycle and options.

3. Press START. The dryer starts at the beginning of the new cycle.

NOTE: If you do not press Start within 5 minutes of selecting the cycle, the dryer automatically shuts off.

NOTE: While cycling through the settings, the current setting will not flash, but the other settings will flash.

4. Press START to save the drying setting.

5. The drying setting you selected will become your new preset

drying setting for all Auto Dry cycles.

Use the Drying Rack to dry items such as sweaters and pillows without tumbling. The drum turns, but the rack does not move.

If your model does not have a drying rack, you may be able to purchase one for your model. To find out whether your model allows drying rack usage and for information on ordering, please refer to the front page of the manual or contact the dealer from whom you purchased your dryer.

NOTE: The rack must be removed for normal tumbling. Do not use the automatic cycle with the drying rack.

To use the drying rack

1. Open dryer door.

__ .............A

A. Front edge

2. Place drying rack inside dryer drum, positioning the back wire on the ledge of the inner dryer back panel. Push down on front edge of drying rack to secure at the front of the dryer.

Changing Modifiers and Options after pressing Start

You can change an Option or Modifier anytime before the selected Option or Modifier begins.

1. Press PAUSE/CANCEL once.

2. Select the new Option and/or Modifiers.

3. Press START to continue the cycle. NOTE: If you happen to press PAUSE/CANCEL twice, the

program clears and your dryer shuts down. Restart the selection process.

Changing the Preset Dryness Level Settings

If all of your loads on all Auto Dry cycles are consistently not as dry as you would like, you may change the preset Dryness Level settings to increase the dryness. This change will affect all of your

Auto Dry cycles.

Your Dryness Level settings can be adjusted to adapt to different installations, environmental conditions or personal preference.

There are 3 drying settings: 1 (factory preset dryness level),

2 (slightly dryer clothes, approximately 15% more drying time) and 3 (much dryer clothes, approximately 30% more drying

time).

1. The Dryness Level settings cannot be changed while the dryer is running.

2. Press and hold the DRYNESS button for 5 seconds. The dryer will beep, and "CF" will be displayed for 1 second

followed by the current drying setting.

3. To select a new drying setting, press the DRYNESS button again until the desired drying setting is shown.

A. Dryerrack front edge

B.Dryerback panel

3. Put the wet items on top of the rack. Leave space between the items so air can reach all the surfaces.

NOTE: Do not allow items to hang over the edge of the rack.

4. Close the door.

5. Press the POWER button.

6. Select a timed drying cycle and temperature (see following chart). Items containing foam, rubber or plastic must be dried on a clothesline or by using the Air Only temperature setting.

7. You must select a time by pressing TIME ADJUST Up or Down. Reset time as needed to complete drying. Refer to the following table.

8. Press (and hold) START button (about 1 second).

This chart shows examples of items that can be rack dried and the suggested cycle, temperature setting and drying time. Actual

drying time will depend on the amount of moisture items hold.

Rack Dry Setting Temp. Time*

Wool Sweaters Timed Low 60

Block to shape and lay flat on Dry

the rack. Stuffed toys or pillows Timed Low 60

Cotton or polyester fiber filled Dry

Stuffed toys or pillows Timed Air Only 90

Foam rubber filled Dry (no heat)

Sneakers or canvas shoes Timed Air Only 90

Dry (no heat)

*(Minutes) Reset time to complete drying, if needed.

DRYERCARE

Every load cleaning

f. The lint screen is located on the top of the dryer. Pull the lint

screen toward you. Roll lint off the screen with your fingers. Do not rinse or wash screen to remove lint. Wet lint is hard to

remove.

2. Push the lint screen firmly back into place.

As needed cleaning

1. Roll lint off screen with your fingers.

2. Wet both sides of lint screen with hot water.

3. Wet a nylon brush with hot water and liquid detergent. Scrub lint screen with the brush to remove residue buildup.

4. Rinse screen with hot water.

5. Thoroughly dry lint screen with a clean towel. Insert lint screen back into dryer.

Keep dryer area clear and free from items that would obstruct the

flow of combustion and ventilation air.

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from dryer.

Place dryer at least 18 inches (46 cm) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

Clean the lint screen before each load. A screen blocked by lint can increase drying time.

IMPORTANT:

• Do not run the dryer with the lint screen loose, damaged, blocked or missing. Doing so can cause overheating and

damage to both the dryer and fabrics.

• If lint falls off the screen into the dryer during removal, check the exhaust hood and remove the lint.

1. Apply a liquid, nonflammable household cleaner to the stained area of the drum and rub with a soft cloth until stain is

removed.

2. Wipe drum thoroughly with a damp cloth.

3. Tumble a load of clean cloths or towels to dry the drum.

NOTE: Garments that contain unstable dyes, such as denim blue jeans or brightly colored cotton items, may discolor the dryer interior. These stains are not harmful to your dryer and will not stain future loads of clothes. Dry unstable dye items inside-out to avoid dye transfer.

From Inside the Dryer Cabinet

Lint should be removed every 2 years, or more often, depending on dryer usage. Cleaning should be done by a qualified person.

From the Exhaust Vent

Lint should be removed every 2 years, or more often, depending on dryer usage.

Vacation care

' '_" ' " : i:_=l I.I!¢I},I.

The dryer light automatically turns on inside the dryer drum when you open the door.

' :_/_ _ :_O_ =¸_"

Operate your dryer only when you are at home. If you will be on vacation or not using your dryer for an extended period of time,

you should:

1. Unplug dryer or disconnect power.

2. Clean lint screen. See "Cleaning the Lint Screen."

Moving care

For power supply cord-connected dryers:

1. Unplug the power supply cord.

2. Make sure leveling legs are secure in dryer base.

3. Use masking tape to secure dryer door.

For direct-wired dryers:

Electrical Shock Hazard

Disconnect power before servicing. Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

To change the drum light

1. Unplug dryer or disconnect power.

2. Open the dryer door. Locate the light bulb cover on the back wall of the dryer. Remove the screw located in the lower right

corner of the cover. Remove the cover.

3. Turn bulb counterclockwise. Replace the bulb with a 10-watt appliance bulb only. Replace the cover and secure with the screw.

4. Plug in dryer or reconnect power.

1. Disconnect power.

2. Disconnect wiring.

3. Make sure leveling legs are secure in dryer base.

4. Use masking tape to secure dryer door.

TROUBLESHOOTING

First try the solutions suggested here and possibly avoid the cost of a service call...

Dryer will not run

Has a household fuse blown, or has a circuit breaker tripped?

There may be 2 household fuses or circuit breakers for the dryer. Check that both fuses are intact and tight, or that both

circuit breakers have not tripped. Replace the fuse or reset the circuit breaker. If the problem continues, call an

electrician.

• Is the correct power supply available? Electric dryers require 240-volt power supply. Check with a

qualified electrician.

• Was a regular fuse used? Use a time-delay fuse.

• Is the dryer door firmly closed?

• Was the Start button firmly pressed? Large loads may require pressing and holding the Start

button for 2-5 seconds.

No heat

Has a household fuse blown, or has a circuit breaker tripped?

The drum may be turning, but you may not have heat. Electric dryers use 2 household fuses or circuit breakers. Replace the fuse or reset the circuit breaker. If the problem continues, call

an electrician.

Unusualsounds

• Has the dryer had a period of non-use? If the dryer hasn't been used for a while, there may be a thumping sound during the first few minutes of operation.

Is a coin, button or paper clip caught between the drum and front or rear of the dryer? Check the front and rear edges of the drum for small objects. Clean out pockets before laundering.

+ 53 hidden pages