Whirlpool YGEW9200LW0, YGEW9200LQ0 Owner’s Manual

ELECTRONIC

ELECTRICDRYER

T£ ,

For assistance call: 1-800-461-5681,

for installation and service, call: 1-800-807-6777

or visit our webeite at... www.whirlpool.com/canada

SECHEUSE

ELECTRIQUE

ELECTRONIQUE

Pour assistance, compoeez le 1-800-461-5681,

pour installation ou service le 1-800-807-6777

ou vieitez notre site web _ www.whirlpooLcom/canada

3979275B

Table of Contents/Table des matieres ................. 2

TABLEOFCONTENTS

TABLEDESMATIERES

DRYER SAFETY .............................................................................. 3

INSTALLATION INSTRUCTIONS .................................................. 4

Tools and Parts ............................................................................ 4

Optional Pedestal ......................................................................... 4

Location Requirements ............................................................... 4

Electrical Requirements ............................................................... 6

Venting Requirements .................................................................. 7

Plan Vent System ......................................................................... 7

Install Vent System ....................................................................... 9

Install Leveling Legs ..................................................................... 9

Level Dryer ................................................................................... 9

Connect Vent ................................................................................ 9

Reverse Door Swing .................................................................. 10

Complete Installation ................................................................. 12

DRYER USE .................................................................................. 13

Starting Your Dryer ..................................................................... 13

Stopping Your Dryer .................................................................. 14

Pausing or Restarting ................................................................. 14

Control Locked ........................................................................... 14

Loading ....................................................................................... 14

Drying and Cycle Tips ................................................................ 15

Status Lights .............................................................................. 15

Cycles ......................................................................................... 15

Additional Features .................................................................... 16

Drying Rack ................................................................................ 17

DRYER CARE ............................................................................... 18

Cleaning the Dryer Location ...................................................... 18

Cleaning the Lint Screen ............................................................ 18

Cleaning the Dryer Interior ......................................................... 18

Removing Accumulated Lint ...................................................... 18

Vacation and Moving Care ......................................................... 19

Changing the Drum Light ........................................................... 19

TROUBLESHOOTING .................................................................. 19

ASSISTANCE OR SERVICE ......................................................... 20

WARRANTY .................................................................................. 21

SI_CURITE DE LA SI_CHEUSE .................................................... 23

INSTRUCTIONS D'INSTALLATION ............................................. 24

Outillage et pieces n_cessaires ................................................. 24

Piedestal facultatif ...................................................................... 24

Emplacement d'installation ........................................................ 24

Specifications electriques .......................................................... 26

Exigences concernant I'evacuation ........................................... 27

Planification du syst_me d'evacuation ...................................... 27

Installation du conduit d'evacuation .......................................... 29

Installation des pieds de nivellement ......................................... 29

Mise & niveau de la secheuse .................................................... 30

Conduit d'evacuation ................................................................. 30

Inversion de I'ouverture de la porte ........................................... 30

Achever I'installation .................................................................. 32

UTILISATION DE LA SI_CHEUSE ................................................ 33

Mise en marche de la secheuse ................................................ 33

Arr_t de la secheuse ................................................................... 34

Arr_t et remise en marche .......................................................... 34

Verrouillage des commandes ..................................................... 34

Chargement ................................................................................ 34

Conseils pour le sechage et les programmes ........................... 35

Temoins lumineux ...................................................................... 35

Programmes ............................................................................... 36

Caract_ristiques supplementaires ............................................. 37

Grille de sechage ........................................................................ 38

ENTRETIEN DE LA SECHEUSE .................................................. 39

Nettoyage de I'emplacement de la secheuse ........................... 39

Nettoyage du filtre h charpie ...................................................... 39

Nettoyage de I'interieur de la secheuse ..................................... 39

Retrait de la charpie accumulee ................................................ 40

Precautions a prendre pour les vacances et avant

un demenagement ..................................................................... 40

Changement de I'ampoule d'eclairage du tambour .................. 40

DC:PANNAGE ................................................................................. 40

ASSISTANCE OU SERVICE ......................................................... 42

GARANTIE ..................................................................................... 43

Wh 1

Whi#_ol °

DRYERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word "DANGER" or

This is the safety alert symbol. "WARNING." These words mean:

You can be killed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic

precautions, including the following:

[]

Read all instructions before using the dryer.

[]

Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could

cause a load to catch fire.

[] Do not dry articles that have been previously

cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, other flammable,

or explosive substances as they give off vapors that could ignite or explode.

[] Do not allow children to play on or in the dryer.

Close supervision of children is necessary when the dryer is used near children.

[] Before the dryer is removed from service or dis-

carded, remove the door to the drying compart- ment.

[] Do not reach into the dryer if the drum is moving. [] Do not install or store the dryer where it will be

exposed to the weather.

[] Do not tamper with controls.

[] Do not repair or replace any part of the dryer or

attempt any servicing unless specifically recom- mended in this Use and Care Guide or in published user-repair instructions that you understand and have

the skills to carry out.

[] Do not use fabric softeners or products to eliminate

static unless recommended by the manufacturer of

the fabric softener or product.

[] Do not use heat to dry articles containing foam rubber

or similarly textured rubber-like materials.

[] Clean lint screen before or after each load. [] Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust, and dirt.

[] The interior of the dryer and exhaust vent should be

cleaned periodically by qualified service personnel.

[] See installation instructions for grounding require-

ments.

SAVE THESE INSTRUCTIONS

INSTALLATION

INSTRUCTIONS

Check that you have everything necessary for correct installation. Proper installation is your responsibility.

• Flat-blade screwdriver • Safety glasses

• Adjustable wrench that • Vent clamps opens to 1 in. (2.5 cm) or

hex-head socket wrench • Caulking gun and (for adjusting dryer feet) new exhaust vent)

• Level

• #2 Phillips screwdriver • Tin snips (new vent

Parts supplied

Remove parts packages from dryer drum. Check that all parts are included.

• Door Reversal Kit

compound (for installing

• Gloves

installations)

Are you placing the dryer on a pedestal? You may purchase a pedestal separately for this dryer. This pedestal will add about 13 in. (33 cm) to the height of your unit for a total height of approximately 51 in. (130 cm).

Optional pedestal

To order, call the dealer from whom you purchased your dryer or refer to the "Assistance or Service" section of this manual. Ask

for Part Number LAB2700LQ (White) or LAB2700LT (Biscuit).

• Parts package

4 Leveling legs

NOTE: Do not use leveling legs if installing the dryer on a pedestal.

Parts needed

Check local codes. Check existing electrical supply and venting. See "Electrical Requirements" and "Venting Requirements" before purchasing parts.

• For close-clearance installations between 31.5 in. (80.01 cm) and 37 in. (93.98 cm), see "Plan Vent System" section for venting requirements.

I_ 37" 91

(93,98 cm)

Mobile home installations require metal exhaust system hardware available for purchase from the dealer from whom you purchased your dryer. For further information, please refer to the "Assistance

or Service" section of this manual.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer. Place dryer at least 18 inches (46 cm) above the

floor for a garage installation. Failure to do so can result in death, explosion,

or fire.

You will need

• A location that allows for proper exhaust installation. See "Venting Requirements."

• A separate 30 amp circuit.

• A grounded electrical outlet located within 2 ft (61 cm) of either side of the dryer. See "Electrical Requirements."

• A sturdy floor to support the total dryer weight of 200 Ibs (90.7 kg). The combined weight of a companion appliance

should also be considered. A level floor with a maximum slope of 1 in. (2.5 cm) under

entire dryer. If slope is greater than 1 in. (2.5 cm), install Extended Dryer Feet Kit, Part No. 279810. Clothes may not tumble properly and automatic sensor cycles may not operate correctly if dryer is not level.

• For a garage installation, you will need to place the dryer at least 18 in. (46 cm) above the floor. If using a pedestal, you will need an additional 6 in. (15.24 cm).

Donotoperateyourdryerattemperaturesbelow45°F(7°C).At lowertemperatures,thedryermightnotshutoffattheendofan automaticcycle.Thiscanresultinlongerdryingtimes.

Installthedryerwhereitisprotectedfromwaterand/orweather. Checkcoderequirements.Somecodeslimit,ordonotpermit,

installationofthedryeringarages,closets,mobilehomes,or sleepingquarters.Contactyourlocalbuildinginspector.

Installation clearances

• The location must be large enough to fully open the dryer door.

• Additional spacing should be considered for ease of installation and servicing.

• Additional clearances might be required for wall, door and floor moldings.

• Additional spacing of I in. (2.5 cm) on all sides of the dryer is recommended to reduce noise transfer.

• Companion appliance spacing should also be considered.

Dryer Dimensions

38"

(96,52 cm)

Minimum installation spacing for recessed or closet installation, with or without a pedestal

• The dimensions shown are for the minimum spacing allowed. For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.

Closet installation - Dryer only

_'_ 48,2

(7.6 cm)

(310cm_) -

(1524"c2m2 }

Io"_ 311/2,,_1o"l

(Ocm) (80cm) (Ocm)

1 2

1. Side view- closet or confined area

2. Closet door with vents

(7.6 cm)

(88 cm)

* Most installations require a minimum 51/2in. (14 cm) clearance

behind the dryer for the exhaust vent with elbow. See "Venting

Requirements."

Minimum installation spacing for custom undercounter installation

The dimensions shown are for the minimum spacing allowed. Custom undercounter installation - Dryer only

0" 27" 0"

(0 cm) "--'_(68.6 cm"_ _- (0 cm)

Recessed or closet installation - Dryer on pedestal

IH 1-14 4,,0,ox

0"_ 27" _i_._ O"

(Ocm) (68.6 cm) (0 cm)

1 2

1. Recessed area

2. Side view - closet or confined area

10"1_8_y2"_1 0"

(Ocrn) (80cm) (Ocm)

Minimum installation spacing for cabinet installation

• The dimensions shown are for the minimum spacing allowed.

• For cabinet installation, with a door, minimum ventilation openings in the top of the cabinet are required.

7"(17.8 cm)

_i-- I1

{22.9cm)

To be sure that the electrical connection is adequate and in conformance with the Canadian Electrical Code, C22.1 -latest edition and all local codes. A copy of the above codes standard may be obtained from: Canadian Standards Association, 178 Rexdale Blvd., Toronto, ON M9W 1R3

CANADA. To supply the required 4 wire, single phase, 115/230-volt, 60-

Hz., AC-only electrical supply on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit

breaker is recommended. Connect to an individual branch circuit.

This dryer is equipped with a CSA International Certified Power Cord intended to be plugged into a standard 14-30R wall receptacle. The cord is 5 ft (1.52 m) in length. Be sure wall receptacle is within reach of dryer's final location.

0 31½ 0

(0cm) (80.0crn)(0crn)(0crn)(68.6cm)(0crn)

Mobile home-additional installation requirements

This dryer is suitable for mobile home installations. The installation must conform to the Manufactured Home

Construction and Safety Standard CAN/CSA-Z240 MH.

Mobile home installations require:

• Metal exhaust system hardware which is available for purchase from your dealer.

Special provisions must be made in mobile homes to introduce outside air into the dryer. The opening (such as a nearby window) should be at least twice as large as the dryer exhaust opening.

4-wire receptacle 14-30R

• Do not use an extension cord. If using a replacement power supply cord, it is recommended

that you use Power Supply Cord Replacement Part Number

9831317. For further information, please reference the service numbers located in the "Assistance and Service" section of this

manual.

GROUNDING INSTRUCTIONS

[] For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current. This dryer is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged

into an appropriate outlet that is properly installed and ground- ed in accordance with all local codes and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or

personnel if you are in doubt as to whether the dryer is proper-

ly grounded. Do not modify the plug provided with the dryer: if

it will not fit the outlet, have a proper outlet installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

Electrical Shock Hazard

Plug into a grounded 4 prong outlet.

Failure to do so can result in death or electrical shock.

It is your responsibility

• Tocontact a qualified electrical installer.

Fire Hazard

Use a heavy metal vent. Do not use a plastic vent.

Do not use a metal foil vent. Failure to follow these instructions can result in

death or fire.

WARNING: To reduce the risk of fire, this dryer MUST BE

EXHAUSTED OUTDOORS.

Exhaust hood must be at least 12 in. (30.5 cm) from the ground or any object that is in the path of the exhaust (such as flowers, rocks or bushes, etc.).

If using an existing vent system, clean lint from the entire length of the system and make sure exhaust hood is not plugged with lint. Replace any plastic or metal foil vent with rigid metal or

flexible metal vent.

Typical exhaust installations

Typical installations vent the dryer from the rear of the dryer.

Other installations are possible.

1 .........

............ 6

......... 7

4 in. (10.2 cm) heavy metal exhaust vent and clamps must be used. DURASAFE TM vent products are recommended.

DURASAFF Mvent products can be purchased from your dealer or by calling Whirlpool Parts and Accessories. For more information, see the "Assistance or Service" section of this

manual.

• The dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling, or a concealed space of a building.

• Do not use an exhaust hood with a magnetic latch.

• Do not install flexible metal vent in enclosed walls, ceilings or floors.

Use clamps to seal all joints. Exhaust vent must not be connected or secured with screws or other fastening devices

which extend into the interior of the duct. Do not use duct tape.

IMPORTANT: Observe all governing codes and ordinances.

improper venting can cause moisture and lint to collect indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint, wall-

paper, carpets, etc.

[] Housecleaning problems and health problems.

Use a heavy metal vent. Do not use plastic or metal foil vent. Rigid metal vent is recommended to prevent crushing and

kinking. Flexible metal vent must be fully extended and supported when

the dryer is in its final position. Remove excess flexible metal vent to avoid sagging and kinking that can result in reduced airflow and poor performance.

An exhaust hood should cap the vent to prevent rodents and insects from entering the home.

1.Dryer

2. Elbow

3. Wall

4. Exhaust hood

5. Clamps

6. Rigid metal or flexible metal vent

7. Vent length necessary to connect elbows

8. Exhaust outlet

Optional exhaust installations

This dryer can be converted to exhaust out the right side, left side, or through the bottom.

Fire Hazard

Cover unused exhaust holes with one of the following kits:

279818 (white) 279925 (biscuit) Contact your local dealer.

Failure to follow these instructions can result in death, fire, electrical shock, or serious injury.

1 2 3

1. Standard rear offset exhaust installation

2. Left or right side exhaust installation

3. Bottom exhaust installation (Not an option with pedestal installations.)

Alternate installations for close clearances Venting systems come in many varieties. Select the type best for

your installation. Two close-clearance installations are shown. Refer to the manufacturer's instructions.

i /Y

\ i \'_ I

1 2

1. Over-The-Top installation (also available with one offset elbow)

2. Periscope installation

\ i

NOTE: The following kits for close clearance alternate installations are available for purchase. Please see the

"Assistance or Service" section of this manual to order.

• Over-The-Top Installation: Part Number 4396028

• Periscope Installation (For use with dryer vent to wall vent mismatch):

Part Number 4396037 - 0 in. (0 cm) to 18 in. (45.72 cm) mismatch

Part Number 4396011 - 18 in. (45.72 cm) to 29 in. (73.66 cm) mismatch

Part Number 4396014 - 29 in. (73.66 cm) to 50 in. (127 cm) mismatch

Special provisions for mobile home installations The exhaust vent must be securely fastened to a noncombustible

portion of the mobile home structure and must not terminate beneath the mobile home. Terminate the exhaust vent outside.

Determine Vent Length

1. Select the route that will provide the straightest and most

direct path outdoors. Plan the installation to use the fewest number of elbows and turns, When using elbows or making turns, allow as much room as possible. Bend vent gradually to avoid kinking. Avoid 90° turns.

Determine vent length. The maximum length of the exhaust system depends upon:

• The type of vent (rigid metal or flexible metal).

• The number of elbows used.

• The type of hood. Recommended hood styles are shown here.

_ ( • )

(10.2 era)

1.Louvered hood style

2. Box hood style

The angled hood style (shown following) is acceptable.

4" _

See the exhaust vent length chart that matches your hood type for the maximum vent lengths you can use.

Exhaust systems longer than specified will:

• Shorten the life of the dryer.

• Reduce performance, resulting in longer drying times and increased energy usage.

Determine the number of elbows you will need. IMPORTANT: Do not use vent runs longer than those

specified in the Vent Length Chart. The following chart helps you determine your maximum vent

length based on the number of 90° turns or elbows you will need and the type of vent (rigid or flexible metal) and hood

that you will use.

Vent Length Chart

Number of Type of Box or Angled

90° turns vent Louvered hoods

or elbows hoods

0 Rigid metal 64 ft (20 m) 58 ft (17.7 m)

Flexible metal 36 ft (11 m) 28 ft (8.5 m)

1 Rigid metal 54 ft (16.5 m) 48 ft (14.6 m)

Flexible metal 31 ft (9.4 m) 23 ft (7 m)

2 Rigid metal 44 ft (13.4 m) 38 ft (11.6 m)

Flexible metal 27 ft (8.2 m) 19 ft (5.8 m)

3 Rigid metal 35 ft (10.7 m) 29 ft (8.8 m)

Flexible metal 25 ft (7.6 m) 17 ft (5.2 m)

4 Rigid metal 27 ft (8.2 m) 21 ft (6.4 m)

Flexible metal 23 ft (7 m) 15 ft (4.6 m)

2. Firmly grasp the body of the dryer (not the console panel).

Gently lay the dryer on the cardboard.

Examine the leveling legs. Find the diamond marking.

NOTE: Side and bottom exhaust installations have a 90° turn inside the dryer. To determine maximum exhaust length, add 1

90° turn to the chart.

1. (Optional) Put on safety glasses and gloves.

2. Install exhaust hood. Use caulking compound to seal exterior wall opening around exhaust hood.

3. Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust hood with 4 in. (10.2 cm)

clamp.

4. Run vent to dryer location. Use the straightest path possible. See "Determine Vent Length." Avoid 90 ° turns. Use clamps to seal all joints. Do not use duct tape, screws or other fastening

devices that extend into the interior of the vent to secure vent.

Excessive Weight Hazard

Use two or more people to move and install

dryer.

Failure to do so can result in back or other injury.

Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs until the diamond marking is no longer

visible.

5. Place a carton corner post under each of the 2 dryer back corners. Stand the dryer up. Slide the dryer on the corner

posts until it is close to its final location. Leave enough room to connect the exhaust vent.

6. Once connection is made and dryer is in final location, remove corner posts and cardboard.

Check the levelness of the dryer. Check levelness first side-to-side, then front-to-back.

If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs up or down and check again for

levelness. NOTE: It might be necessary to level the dryer again after it has

been moved into its final position.

1. To protect the floor, use a large flat piece of cardboard from the dryer carton. Place cardboard under the entire back edge of the dryer. See illustration.

1. Using a 4 in. (10.2 cm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust outlet

and inside the exhaust hood. Make sure the vent is secured to exhaust hood with a 4 in. (10.2 cm) clamp.

2. Move dryer into final position. Do not crush or kink vent. Make sure dryer is level.

3. (On gas models) Check to be sure there are no kinks in the flexible gas line.

Youcanchangeyourdoorswingfromaright-sideopeningtoa left-sideopening,ifdesired.

Locatethedoorreversingkitthatwasshippedinthedrumof yourdryer.Youwillneedthesepartstocompletethedoor

reversal. Loosendoortrim

1. Placeatowelorsoftclothontopofthedryerorworkspace toprotectthesurface.

2. Loosentheplastictrimaboveandbelowthehandlefiller. Carefullypulloutonthetrimuntilitunsnaps.Removethe

handlefillerandsetaside.

1. Plastic trim

2. Handle filler

Remove the door

1. Open the dryer door. Remove the 5 screws that hold the door hinge on the front panel of the dryer. Loosen, but do not remove, the screw with the top keyhole opening LAST (second from the top).

Lift and pull forward on the door so that the screwhead clears the keyhole. Remove the door.

Lay the dryer door on a flat, protected surface with the inside door assembly facing up. Remove the 2 screws holding the handle to the door. Pull handle straight out and set aside. A new handle is provided.

Loosen the plastic trim above and below the hinge cover. Carefully pull out on the trim until it unsnaps. Remove the hinge cover and set aside.

j//

1. Plastic trim

2. Hinge cover

Keep the original handle filler and hinge cover in case you decide to return the door to its original position.

A new handle filler and hinge cover are provided in the door reversing kit that will be installed in a later step.

NOTE: Keep this handle in case you decide to return the door to its original position.

Remove the 6 screws to release the outer door assembly from the inner door assembly (see illustration). It is important that you remove ONLY the 6 indicated screws.

Lift the inner door assembly off of the outer door assembly. Set the outer door assembly aside.

Reverse the hinge and hinge bracket

1. Place the inner door, screwhead side up, on the work surface.

2. Remove the 4 screws that hold the hinge to the door.

Remove the 2 screws that hold the handle bracket to the door.

Insert the new handle into the side opening of the door. Make sure the handle seats all the way in, and the holes line up with

the holes in the door. Reattach with 2 screws.

Use a small flat-head screwdriver to remove hole plugs in the door opening. Slide the head of the screwdriver under the cap of each hole plug, being careful not to scratch the dryer surface. Lift up. Remove the hole plugs in the door opening and insert in the opposite side.

Insert a screw in the second opening from the top of the hinge opening and partially tighten, Hang the door by placing

the top hinge keyhole over the second screwhead and tighten the screw. By putting this screw in first, the door will hang in

place while you insert and tighten the remaining 4 screws.

4. Move hinge to the other side and reattach.

5. Move handle bracket to the other side and reattach.

6. Set the inner door assembly aside.

Reinstalling the door

1. Check for fingerprints on the glass. Clean if necessary.

2. Place the inner door assembly into the outer door assembly. Align the hinge in the opening on the side, To fit correctly, the inside door assembly edge is completely inside the outside door assembly edge,

3. Reassemble the inner and outer door assemblies with the 6 screws.

Install new handle filler and hinge cover

1. Using the new handle filler provided in the reversing kit, hook

the top of the handle filler onto the loosened upper door trim, Snap the joined pieces into place, You may need to use the heel of your hand to firmly snap the pieces back into place,

2. Hook the bottom of the handle filler onto the lower door trim and snap into place,

3. Repeat steps 1 and 2 to install the hinge cover on the opposite side.

4. Close the door and check that it latches securely.

1. Check to be sure all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.

2. Check to be sure you have all of your tools.

3. Dispose of all packaging materials.

4. Check the dryer's final location. Be sure the vent is not crushed or kinked.

5. Check to be sure the dryer is level. (See "Level Dryer.")

6. Plug into a grounded outlet. Turn power on.

7. Remove the blue protective film on the console and any tape remaining on the dryer.

8. Read "Dryer Use."

9. Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust.

10. Set the dryer on a full heat cycle (not an air cycle) for 20 minutes and start the dryer.

If the dryer will not start, check the following:

• Controls are set in a running or "On" position.

• Start button has been pushed firmly.

• Dryer is plugged into a grounded outlet.

• Electrical supplyis connected.

• House fuse is intact and tight; or circuit breaker has not

tripped.

• Dryer door is closed.

11. When the dryer has been running for 5 minutes, open the dryer door and feel for heat.

If you do not feel heat, turn the dryer off and check the

following:

• There may be 2 fuses or circuit breakers for the dryer. Check to make sure both fuses are intact and tight, or that both circuit breakers have not tripped. If there is still no heat, contact a qualified technician.

NOTE: You may notice a burning odor when the dryer is first heated. This odor is common when the heating element is first used. The odor will go away.

DRYERUSE

Normal

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from dryer.

Do not dry anything that has ever had anything

flammable on it (even after washing).

Failure to follow these instructions can result in death, explosion, or fire.

o High

o _ew o Louder

0 Extra Low 0 Softer

o on

Wrinkle Shield Femperatute End Of Cycle Signal

WARNING: To reduce the risk of fire, electric shock, or injury to

persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.

The following is a guide to starting your dryer. Please refer to specific sections of this manual for more detailed information,

1. Clean lint screen before or after each cycle.

2. Place laundry into dryer and shut door. See "Loading,"

3. Rotate the dial to select either an Automatic or Manual Cycle then press the CONTROL ON button. The preset settings and drying time for the cycle chosen will be displayed.

To use an Automatic Cycle

Point the dial to an Automatic Cycle. Select DRYNESS LEVEL to adjust how dry you want the

load to be. The time displayed is an estimated length of the cycle based on the Dryness Level selected. As the cycle runs, the control senses the dryness of the load and adjusts the time automatically for the selected Dryness

Level.

O AJtOn_y 0 Off

0 More

0 Less

Fire Hazard

No washer can completely remove oil. Do not dry anything that has ever had any type of

oil on it (including cooking oils). Items containing foam, rubber, or plastic must be

dried on a clothesline or by using an Air Cycle. Failure to follow these instructions can result in

death or fire.

Dryness

Level

NOTE: Time is not adjustable for Automatic Cycles. Pressing the More Time or Less Time buttons will cause a triple beep, indicating that the time cannot be changed.

Press the WRINKLE SHIELD TM feature button if this option is desired.

Press the END OF CYCLE SIGNAL button to set signal volume to desired level.

Press (and hold) HOLD TO START button until dryer starts (about 1 second).

Once an Automatic cycle has started, the WRINKLE SHIELD TM feature and the End of Cycle Signal level can be adjusted. Press the PAUSE/CANCEL key twice to stop the dryer and clear the settings, allowing you to select another cycle and Dryness Level.

To use a Manual Cycle

Rotate the dial to select a Manual Cycle. Press MORE TIME or LESS TIME until the desired drying

time is displayed. Tap MORE TIME or LESS TIME and the time will change by 1-minute intervals. Press and hold MORE TIME or LESS TIME and the time will change by 5-minute intervals. The initial time displayed is the actual drying time.

Mo_

Time

Less

_me

NOTE: The More Time or Less Time feature can be used only with Manual Cycles.

• Press TEMPERATURE until the desired temperature glows.

NOTE: Pressing the Dryness Level button will cause the triple beep indicating that this option is not selectable. Also, a Dryness Level is not indicated.

• Press the WRINKLE SHIELD TM feature button if this option is desired.

• Press the END OF CYCLE SIGNAL button to set volume to desired level.

• Press (and hold) HOLD TO START button until dryer starts (about 1 second).

While a Manual Cycle is running, you can change the settings for Time, Temperature, the WRINKLE SHIELD TM feature, and the End of Cycle Signal. Press the PAUSE/CANCEL key twice to stop the dryer and clear the settings, allowing you to select another cycle.

This feature allows you to lock your settings to prevent unintended use of the dryer. You can also use the Control Locked feature to prevent unintended cycle or option changes during dryer operation.

To enable the Control Locked feature when dryer is running:

Press and hold the END OF CYCLE SIGNAL button for three seconds. The control is locked when a single beep is heard and

the Control Locked status light is on.

• When the dryer is off, it is not necessary to press the Control On button before activating the Control Locked feature.

To unlock:

Press and hold the END OF CYCLE SIGNAL button for three seconds to turn this feature off.

NOTE: When the dryer is running and Control Locked is on, the dryer can be stopped by pressing the Pause/Cancel button, but

can't be restarted until the control is unlocked.

Properly loading your dryer can lower your utility bill and prolong the life of your garments.

Loading suggestions

• Load the dryer by the amount of space items take up, not by their weight.

• Do not overload the dryer. This causes wrinkling and uneven drying.

Super Capacity Plus Dryers

To stop your dryer at anytime Press PAUSE/CANCELtwice or open the door.

To pause the dryer at any time Open the door or press PAUSE/CANCEL once.

To restart the dryer Close the door and press (and hold) HOLD TO START button until

dryer starts, NOTE: Drying will continue from where the cycle was interrupted

if you close the door and press Start within 5 minutes. Ifthe cycle is interrupted for more than 5 minutes, the dryer will shut off. Select new cycle settings before restarting the dryer.

Heavy Work Clothes

4 jeans 2 sweatpants 4 workpants 2 sweatshirts

4 workshirts

Towels

10 bath towels

14 washcloths

10 hand towels

Mixed Load

3 sheets (1 king, 2 twin) 9 T-shirts 4 pillowcases 9 shorts

3 shirts 10 handkerchiefs 3 blouses

+ 30 hidden pages