Whirlpool YET17JKYJW00, YET18TKXJW00, YET17JKXJW00, YET14JKYJW00, YET14JKXJW00 Owner’s Manual
...
TOP-MOUNT
REFRIGERATOR
For questions about features, operation/performance,
parts accessories or service, call: 1-800-253-1301.
In Canada, call for assistance 1-800-461-5681, for installation
www.whirlpool.com or www.whirlpool.com/canada
and service, call: 1-800-807-6777
or visit our website at...
RI FRIGI RATEUR
suPr. osr
Au Canada, pour assistance, composer le 1-800-461-5681, pour
Table of Contents/Table des mati_res .......................................... 2
installation ou service 1-800-807-6777
ou visitez notre site web &
www.whirlpool.com/canada
2210108
TABLEOFCONTENTS
TABLEDES MATIERES
REFRIGERATOR SAFETY .......................................................... 3
INSTALLING YOUR REFRIGERATOR ....................................... 4
Unpacking Your Refrigerator ....................................................... 4
Space Requirements .................................................................... 4
Electrical Requirements ............................................................... 5
Connecting the Refrigerator to a Water Source .......................... 5
Refrigerator Doors: Removing, Reversing and Replacing ........... 7
Door Closing and Alignment ........................................................ 8
Understanding Sounds You May Hear........................................ 9
USING YOUR REFRIGERATOR ................................................. 9
Ensuring Proper Air Circulation .................................................... 9
Setting the Control(s) ................................................................. 10
Adjusting Control Settings ......................................................... 10
REFRIGERATOR FEATURES ................................................... 11
Refrigerator Shelves ................................................................... 11
Meat Drawer and Cover ............................................................. 11
Crisper and Crisper Cover ......................................................... 12
Utility or Egg Bin ......................................................................... 12
FREEZER FEATURES .............................................................. 12
Ice Maker .................................................................................... 12
Freezer Shelf .............................................................................. 13
DOOR FEATURES .................................................................... 13
Drop-in Door Rails ...................................................................... 13
CARING FOR YOUR REFRIGERATOR ................................... 13
Cleaning Your Refrigerator ......................................................... 13
Changing the Light Bulb ............................................................ 14
Power Interruptions .................................................................... 14
Vacation and Moving Care ......................................................... 14
TROUBLESHOOTING ............................................................... 15
ASSISTANCE OR SERVICE ..................................................... 17
WARRANTY .............................................................................. 18
S¢:CURIT¢: DU RC:FRIGC:RATEUR ........................................... 19
INSTALLATION DU RC:FRIGC:RATEUR ................................... 20
Deballage de votre refrigerateur ................................................ 20
Espacement requis ..................................................................... 20
Specifications electriques .......................................................... 21
Raccordement du refrigerateur a une canalisation d'eau .........21
Portes du refrigerateur :
Demontage, inversion et reinstallation ....................................... 23
Fermeture et alignement des portes .......................................... 25
Les bruits de I'appareil que vous pouvez entendre ................... 25
UTILISATION DU RC:FRIGC:RATEUR ....................................... 26
Pour s'assurer d'une circulation d'air appropriee ...................... 26
Reglage des commandes .......................................................... 26
Ajustement des reglages de commande ................................... 26
CARACTC:RISTIQUES DU RC:FRIGC:RATEUR ......................... 27
Tablettes du refrigerateur ........................................................... 27
Bac a viande et couvercle .......................................................... 27
Bac a legumes et couvercle ....................................................... 28
Casier utilitaire ou oeufrier .......................................................... 28
CARACTC:RISTIQUES DU CONGC:LATEUR ............................ 29
Machine a gla(_ons ..................................................................... 29
Clayette du congelateur ............................................................. 29
CARACTC:RISTIQUES
DE LA PORTE ............................................................................ 30
Tringles dans la porte ................................................................. 30
ENTRETIEN DE VOTRE RC:FRIGC:RATEUR ............................ 30
Nettoyage du refrigerateur ......................................................... 30
Remplacement de I'ampoule d'_clairage .................................. 31
Pannes de courant ..................................................................... 31
Entretien avant les vacances
ou Iors d'un demenagement ...................................................... 31
DC:PANNAGE ............................................................................. 32
ASSISTANCE OU SERVICE ...................................................... 34
GARANTI E................................................................................. 35
REFRIGERATORSAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or
This is the safety alert symbol.
"WARNING." These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic
precautions:
• Plug into a grounded 3 prong outlet.
• Do not remove ground prong.
• Do not use an adapter.
• Do not use an extension cord.
• Disconnect power before servicing.
• Replace all panels before operating.
• Remove doors from your old refrigerator.
• Use nonflammable cleaner.
• Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
• Use two or more people to move and install
refrigerator.
• Disconnect power before installing ice maker (on
ice maker kit ready models only).
• Use a sturdy glass when dispensing ice or water
(on some models).
SAVETHESE INSTRUCTIONS
Proper Disposal of YourOldRefrigerator
Suffocation Hazard
Remove doors from your old refrigerator.
Failure to do so can result in death or
brain damage.
IMPORTANT: Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are still dangerous
- even if they will sit for "just a few days." Ifyou are getting rid of
your old refrigerator, please follow these instructions to help
prevent accidents.
Before you throw away your old refrigerator or freezer:
• Take off the doors.
• Leave the shelves in place so that children may not easily
climb inside.
INSTALLINGYOUR
REFRIGERATOR
Excessive Weight Hazard
Use two or more people to move and install
refrigerator.
Failure to do so can result in back or other injury.
Remove shelves from the shipping position (shelves are
shipped upside down):
IMPORTANT: Do not clean glass shelves with warm water when
they are cold. Shelves may break if exposed to sudden
temperature changes or impact, such as bumping. For your
protection, tempered glass is designed to shatter into many small
pebble-size pieces. This is normal.
NOTE: Glass shelves are heavy. Use special care when removing
them to avoid impact from dropping.
1. Grasp the front of the upper shelf with one hand and use the
other hand to remove packing material from the shelf area.
2. Lower the front of the upper shelf until shelf hooks can be
removed from the shelf supports and pull the shelf forward.
3. Flip the shelf over and insert the rear shelf hooks into the
shelf supports. Tilt the front of shelf up until rear shelf hooks
drop into the shelf supports.
4. Lower the front of the shelf and check to make sure that it is
securely in position.
Removing packaging materials
• Remove tape and any labels from your refrigerator before
using (except the model and serial number label).
To remove any remaining tape or glue, rub the area briskly
with your thumb. Tape or glue residue can also be easily
removed by rubbing a small amount of liquid dish soap over
the adhesive with your fingers. Wipe with warm water and
dry.
Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your refrigerator. For
more information, see "Refrigerator Safety" section.
On some models, shelves, bins, door shelf rails, and other
feature parts may be packaged in the Interior FeaturePak.
Follow the instructions contained in the package for proper
assembly.
IMPORTANT:
• Depending on your model, do not remove any permanent
instruction labels inside your refrigerator or the Tech Sheet
that is fastened behind the base grille.
Depending on your model, do not remove the white
Styrofoam insert that is located behind the control panel on
the ceiling of the refrigerator. The insert is part of the
refrigerator and not part of the packing material. If the insert
is removed, ice may migrate down from the freezer and cause
icicles to form.
When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator
for cleaning or service, be sure to protect the floor.
Always pull the refrigerator straight out when moving it.
Do not wiggle or "walk" the refrigerator when trying to move
it, as floor damage could occur.
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion,
or fire.
To ensure proper ventilation for your refrigerator, allow for a
.5 in. (1.25 cm) space on each side
Allow 3 in. (7.5 cm) of space between overhead cabinets and
refrigerator top.
Allow at least 1 in. (2.5 cm) between back of cabinet and the
wall.
II I
u
_11I
/
/
2" (5.08 era)
• If your refrigerator has an ice maker, make sure you leave
some extra space at the back for the water line connections.
• If you are installing your refrigerator next to a fixed wall, leave
2 in. (5.08 cm) minimum on the hinge side (depending on your
model) to allow for the door to swing open.
• Level the refrigerator (See "Door Closing and Alignment").
NOTE: Do not install the refrigerator near an oven, radiator, or
other heat source, nor in a location where the temperature will fall
below 40 ° F (5° C).
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical
connection:
Recommended grounding method
A 115 Volt, 60 Hz., AC only 15 or 20 ampere fused, grounded
electrical supply is required. It is recommended that a separate
circuit serving only your refrigerator be provided. Use an outlet
that cannot be turned off by a switch. Do not use an extension
cord.
NOTE: Before performing any type of installation, cleaning, or
removing a light bulb, turn the control, (Thermostat, Refrigerator
or Freezer Control depending on the model) to OFF and then
disconnect the refrigerator from the electrical source. When you
are finished, reconnect the refrigerator to the electrical source
and reset the control (Thermostat, Refrigerator or Freezer Control
depending on the model) to the desired setting.
C ..... •
0 <: SO 'C
Read all directions carefully before you begin.
IMPORTANT:
• If operating the refrigerator before installing the water
connection, turn ice maker to the OFF position to prevent
operation without water.
• All installations must be in accordance with local plumbing
code requirements.
• Use copper tubing and check for leaks.
• Install copper tubing only in areas where temperatures will
remain above freezing.
• It may take up to 24 hours for your ice maker to begin
producing ice.
Tools required:
• Standard screwdriver
• 7_6in. and 1/2in. open-end wrenches or two adjustable
wrenches
• ¼in. nut driver
• ¼in. drill bit
• Hand drill or electric drill (properly grounded)
NOTE: Your refrigerator dealer has a kit available with a
1/4in. (6.35 mm) saddle-type shut-off valve, a union, and copper
tubing. Before purchasing, make sure a saddle-type valve
complies with your local plumbing codes. Do not use a piercing-
type or 3/16in. (4.76 mm) saddle valve which reduces water flow
and clogs more easily.
Cold Water Supply
The ice maker water valve contains aflow washer which is used
as a water pressure regulator. The ice maker needs to be
connected to a cold water line with water pressure between 30
and 120 psi. If a problem occurs, call your utility company.
Connecting to water line:
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.
3. Find a 1/2in. (1.27 ram) to 11/4in. (3.18 cm) vertical COLD
water pipe near the refrigerator.
NOTE: Horizontal pipe will work, but the following procedure
must be followed: Drill on the top side of the pipe, not the
bottom. This will help keep water away from the drill. This
also keeps normal sediment from collecting in the valve.
4.
To determine the length of copper tubing you will need,
measure from connection on lower left rear of refrigerator to
water pipe. Add 7 feet (2.1 m) to allow for moving refrigerator
for cleaning. Use 1/4in. (6.35 mm) O.D. (outside diameter)
copper tubing. Be sure both ends of copper tubing are cut
square.
5.
Using a grounded drill, drill a 1/4in. (6.35 mm) hole in the cold Style 1
water pipe you have selected.
...... •........ 2
7 ._ ................3
1. Cold Water Pipe
2. Pipe Clamp
3. Copper Tubing
4. Compression Nut
5. Compression Sleeve
6. Shut-Off Valve
7. Packing Nut
1. Tube Clamp
2. Copper Tubing
3. Compression Nut
4. Valve Inlet
6. Fasten shut-off valve to cold water pipe with pipe clamp. Be
sure outlet end is solidly in the 1/4in. (6.35 mm) drilled hole in
the water pipe and that washer is under the pipe clamp.
Tighten packing nut. Tighten the pipe clamp screws carefully
and evenly so washer makes a watertight seal. Do not
overtighten or you may crush the copper tubing, especially if
soft (coiled) copper tubing is used. Now you are ready to
connect the copper tubing•
7. Slip compression sleeve and compression nut on copper
tubing as shown. Insert end of tubing into outlet end squarely
as far as it will go. Screw compression nut onto outlet end
with adjustable wrench. Do not overtighten.
8. Place the free end of the tubing into a container or sink, and
turn ON main water supply and flush out tubing until water is
clear• Turn OFF shut-off valve on the water pipe. Coil copper
tubing.
Connecting to refrigerator:
NOTE: The first step for connecting the water line to your
refrigerator is different depending on the type of water valve
provided with your refrigerator• See the diagrams below to
determine the style of valve you have. (On kit models, assemble
water valve to refrigerator per kit instructions.)
1. For Style 1, disconnect the tube clamp on the back of the
product and insert the copper tubing through the clamp, as
shown. Remove the tape label from the valve inlet and insert
copper tubing until it bottoms out (approximately ¾ in. [1.9
cm]). Tighten nut by hand as much as possible; then turn the
nut an additional 1/2turn using a wrench• Do not overtighten.
Re-attach the tube clamp and tube to the back of the cabinet.
Skip to Step 2.
For Style 2, disconnect the tube clamp on the back of the
product and insert copper tubing through the clamp as
shown. Attach the copper tube to the valve inlet using a
compression nut and sleeve as shown. Tighten the
compression nut. Do not overtighten. Re-attach the tube
clamp and tube to the back of the cabinet• Move to Step 2.
2. Turn shut-off valve ON. Check For Leaks. Tighten any
connections (including connections at the valve) or nuts that
leak.
Style 2
2
1. Tube Clamp
2. Copper Tubing
3. Compression Nut
3. The ice maker is equipped with a built-in water strainer. If
local water conditions require periodic cleaning or a well is
your source of water supply, a second water strainer should
be installed in the 1/4in. (6.35 mm) water line. Obtain a water
strainer from your nearest appliance dealer. Install at either
tube connection.
4. Plug in refrigerator or reconnect power•
_ ._ _ ._ _ _ # _ _ _'_ _ _ _._ T¸¸ _ _,._ _ / _ o _
TOOLS NEEDED: %6in. hex-head socket wrench, No. 2 Phillips screwdriver, flat-head screwdriver, %6 in. open-end wrench, flat 2 in.
putty knife.
IMPORTANT: Before you begin, turn the refrigerator control OFE unplug refrigerator or disconnect power. Remove food from doors.
I I
1. Cabinet Hinge Hole Plugs
1.5/_,, Hex-Head Hinge
Screws and Washers
1. Door Hinge Hole Plug
%,
1. Flat-Head Handle Screws
2. Freezer Handle
1. Door Handle Sealing Screws
Front View Side View
1. Door Step Screw 1 2
2. Door Step
1
Y
1. Door Handle
Seal Screw Front
I. Flat-Head Handle Screw
2. Refrigerator Handle
3. Handle Screw
4. Screw Cover
Door and hinge removal
5/16in Hex-Head Hinge Screw
1.
Unplug refrigerator or disconnect power.
2.
Keep both doors closed until you are ready to lift them free
from the cabinet.
NOTE: Provide additional support for the doors while the
hinges are being moved. Do not depend on the door magnets
to hold the doors in place while you are working.
3. Remove the parts for the top hinge as shown in Top Hinge
graphic.
4. Lift the freezer door free from the cabinet.
5. Remove the parts for the center hinge as shown inthe Center
Hinge graphic.
6. Lift the refrigerator door free from the cabinet,
7. Remove the parts for the bottom hinge as shown in the
Bottom Hinge graphic,
IMPORTANT: If you want to reverse your doors so that they
open in the opposite direction, follow these steps. If you are
not reversing the doors, see "Door and Hinge Replacement."
Door reversal (optional)
Door Stop Screw
Door Handle Sealing Screw
Flat-Head Handle Screw
Door Hinge Hole Plug
Cabinet Hinge Hole Plug
Door Handle Screw Cover
4. Remove door handle sealing screws. Move to opposite side
of refrigerator door as shown (see Graphic 4).
5. Remove door handle seal screw front. Move to opposite side
of refrigerator door as shown (see Graphic 7).
6. Remove door stop. Move to opposite side of refrigerator door
as shown (see Graphic 5),
7. Position refrigerator handle on opposite side of the
refrigerator door as shown (see Graphic 6). Drive top two
screws in handle first, Align lower portion of handle and drive
bottom screw.
8. Replace screw cover (see Graphic 6),
9. Tighten all screws. Set aside refrigerator door until bottom
hinge is installed on product,
Door and hinge replacement
Note: Graphic may be reversed if door swing is reversed.
1. Replace the parts for the bottom hinge as shown. Tighten
screws,
2. Replace the refrigerator door.
NOTE: Provide additional support for the doors while the
hinges are being moved. Do not depend on the door magnets
to hold the doors in place while you are working.
3. Assemble the parts for the center hinge as shown and tighten
all screws (see Center Hinge graphic).
4. Replace the freezer door.
5. Assemble the parts the top hinge as shown (see Top Hinge
graphic). Do not tighten screws completely.
6. Line up the doors so that the bottom of the freezer door
aligns evenly with the top of the refrigerator door. Tighten all
screws,
Final Steps
1. Check all holes to make sure that hole plugs and screws are
in place.
2. Plug in refrigerator or reconnect power.
3. Reset the controls (see "Setting the Controls" section.)
Door Handle Seal Screw Front
Round-Head Handle Screw
Cabinet
1. Remove %6 in. hex-head hinge screws from handle side and
move them to opposite side (see Graphic 1-1).
2. Remove cabinet hinge hole plugs from cabinet top and move
them to opposite side hinge holes as shown (see Graphic 1-
2).
Freezer door
1. Remove freezer handle assembly as shown. Keep all parts
together (see Graphic 2).
2. Remove door hinge hole plug, Move to opposite side as
shown (see Graphic 3).
3. Remove door handle sealing screws. Move to opposite side
of freezer door as shown (see Graphic 4),
4. Remove door stop. Move to opposite side of freezer door as
shown (see Graphic 5).
5. Position freezer handle on opposite side of freezer door.
Assemble handle on door as shown (see
Graphic 2).
6. Tighten all screws. Set aside door until hinges and refrigerator
compartment door are in place,
Refrigerator door
1. Remove the screw cover (see Graphic 6).
2. Remove refrigerator handle assembly as shown. Keep all
parts together (see Graphic 6).
3. Remove door hinge hole plug from refrigerator door. Move to
opposite side hinge hole as shown (see Graphic 3).
Your refrigerator has two front adjustable rollers - one on the right
and one on the left. If your refrigerator seems unsteady or you
want the doors to close easier, adjust the refrigerator's tilt using
the instructions below:
1. Roll out the refrigerator and use a level to check the floor at
the back from side-to-side, If needed, use shims to level the
back of the refrigerator if it is uneven. Roll the refrigerator
back into place with the rear rollers on top of any shim(s)
used so that the rear of the refrigerator is level,
2. With the rear already level and the refrigerator in place, use
the bottom leveling screws to level the refrigerator from side-
to-side. They are part of the front roller assemblies, which are
found at the base of the refrigerator on either side.
NOTE: Having someone push against the top of the
refrigerator takes some weight off the leveling screws and
rollers, This makes it easier to adjust the screws.
Style 1
Water dripping on the defrost heater during a defrost cycle
may cause a sizzling sound.
You may hear the evaporator fan motor circulating the air
through the refrigerator and freezer compartments.
As each cycle ends, you may hear a gurgling sound due to
the refrigerant flowing in your refrigerator.
Contraction and expansion of the inside walls may cause a
popping noise.
You may hear air being forced over the condenser by the
condenser fan.
You may hear water running into the drain pan during the
defrost cycle.
USINGYOUR
Style 2
3. Depending on your model, to level your refrigerator you may
either turn the screw clockwise to raise that side of the
refrigerator or turn the screw counterclockwise to lower that
side. Place a level on top of the refrigerator to check
adjustments.
4. If the doors do not close on their own, you will need to raise
the front of the refrigerator so it is slightly higher than the
back. To do this, turn both leveling screws clockwise 1/2turn.
IMPORTANT: Be sure to turn both screws an equal amount
or the refrigerator will no longer be level side-to-side.
5. Open doors and check if they close automatically. If not,
repeat steps 3 and 4.
6. Using a level, check to see if the refrigerator is still level side-
to-side. Readjust if necessary.
REFRIGERATOR
In order to ensure proper temperatures, you need to permit air
flow between the refrigerator and freezer sections. As shown in
the illustration, cool air enters through the bottom of the freezer
section and moves up. Most of the air then flows through the
freezer section vents and recirculates under the freezer floor. The
rest of the air enters the refrigerator section through the top vent.
Your new refrigerator may make sounds that your old one didn't
make. Because the sounds are new to you, you might be
concerned about them. Most of the new sounds are normal. Hard
surfaces, like the floor, walls, and cabinets, can make the sounds
seem louder than they actually are. The following describes the
kinds of sounds and what may be making them.
• If your product is equipped with an ice maker, you will hear a
buzzing sound when the water valve opens to fill the ice
maker for each cycle.
The defrost timer will click when the automatic defrost cycle
begins and ends. Also, the Thermostat Control (or
Refrigerator Control depending on the model) will click when
cycling on and off.
• Rattling noises may come from the flow of refrigerant, the
water line, or items stored on top of the refrigerator.
Your refrigerator is designed to run more efficiently to keep
your food items at the desired temperature. The high
efficiency compressor may cause your new refrigerator to run
longer than your old one, and you may hear a pulsating or
high-pitched sound.
Do not block any of these vents with food packages. If the
vents are blocked, airflow will be prevented and temperature and
moisture problems may occur.
IMPORTANT: Because air circulates between both sections, any
odors formed in one section will transfer to the other. You must
thoroughly clean both sections to eliminate odors. To prevent
odor transfer and drying out of food, wrap or cover foods tightly.
(See the "Refrigerator Safety" section for details.)
C _ , _,'_ .... _ _, _ _'_ _ _
K_ _ !} "_ _";_ •
For your convenience, the refrigerator controls are preset at
the factory. Controls for the refrigerator and freezer are located
in the top of the refrigerator section.
When you first install your refrigerator, make sure that the
control(s) are still preset. The control(s} should be at the
"mid-settings" as shown for each style of control.
Mid-setting "3"
OFF
5 1
Mid-setting "3"
Mid-setting "4"
REFmGERATOR
NOTE: To turn your refrigerator off, turn the refrigerator control to
the word OFF or until the word OFF appears, as shown below.
Your product will not cool when the refrigerator control is set to
OFR
!i .....
Give the refrigerator time to cool down completely before adding
food. It is best to wait 24 hours before you put food into the
refrigerator. The "mid-settings" indicated in the previous section
should be correct for normal household refrigerator usage. The
controls are set correctly when milk or juice is as cold as you like
and when ice cream is firm.
For models with two controls:
The Refrigerator Control functions as the thermostat for the entire
product (refrigerator and freezer sections). The higher the number
setting, the longer the compressor will run to keep the
temperature colder. The Freezer Control adjusts the cold air flow
from the freezer to the refrigerator.
If you need to adjust temperatures in the refrigerator or freezer,
start by adjusting the refrigerator first. Wait 24 hours after the
refrigerator adjustment to check the freezer temperature. If it is
too warm or too cold, then adjust the Freezer Control as well.
For models with a single control:
The Temperature Control functions as the thermostat for the
entire product (refrigerator and freezer sections). The higher the
number setting, the longer the compressor will run to keep the
temperature colder.
Use the settings listed in the chart below as a guide. Always
remember to wait at least 24 hours between adjustments.
CONDITION/REASON: ADJUSTMENT:
REFRIGERATOR section
too warm
• Door opened often
• Large amount of food added
• Room temperature very warm
• Blocked air stream
RECOMMENDED
Turn
REFRIGERATOR
Control or
TEMPERATURE
Control to next
higher number, wait
24 hours, then re-
check
Move items out of
air stream
Give your refrigerator time to cool down completely before
adding food. It is best to wait 24 hours before you put food into
the refrigerator.
IMPORTANT: If you add food before the refrigerator has cooled
completely, your food may spoil. Turning the Refrigerator or
Freezer Control(s} to a higher (colder} than recommended
setting will not cool the compartments any faster.
On models with two controls, the Freezer Control functions as an
airflow director. Setting "1" will direct more of the cold air into the
refrigerator section, while setting "5" (or "7" depending on your
model) will direct more of the cold air into the freezer section. The
cold air flows from the freezer compartment through the top vent
into your fresh food section (see diagram in the "Ensuring Proper
Air Circulation" section). On models with one control, the airflow
does not require adjustment.
FREEZER section too warm/ice not
made fast enough
• Door opened often
• Large amount of food added
• Very cold room temperature
Turn FREEZER
Control or
TEMPERATURE
Control to next
higher number, wait
24 hours, then re-
check
(can't cycle often enough)
• Heavy ice usage Move items out of
• Blocked air stream
air stream
10
CONDITION/REASON: ADJUSTMENT:
REFRIGERATOR section Turn
too cold REFRIGERATOR
• Controls not set correctly for TEMPERATURE
your conditions Control to next
• Blocked air stream
FREEZER section too cold
• Controls not set correctly for
your conditions
• Blocked air stream
RECOMMENDED
Control or
lower number, wait
24 hours, then re-
check
Move items out of
air stream
Turn FREEZER
Control or
TEMPERATURE
Control to next
lower number, wait
24 hours, then re-
check
Move items out of
air stream
REFRIGERATOR
FEATURES
To remove and replace the meat drawer:
1. Slide meat drawer out to the stop.
2. Lift front of meat drawer with one hand while supporting
bottom of drawer with other hand. Slide drawer out the rest of
the way.
3. Replace the drawer by sliding it back in fully past the drawer
stop.
To remove and replace the meat drawer cover
(Glass meat drawer cover on some models}:
1. Remove the meat drawer.
2. Push the cover back to release the rear clips from the shelf.
Tilt the cover up at the front, and pull it forward.
3. Replace the meat drawer cover by fitting the notches and
clips on underside of the cover over the rear and center
crossbars on the shelf.
4. Lower cover into place and pull the cover forward to secure
the rear clips onto the shelf.
5. Replace the meat drawer.
Your model may have some or all of these features. Features that
can be purchased separately as product accessories are labeled
with the word "Accessory." Not all accessories will fit all models.
If you are interested in purchasing one of the accessories, please
call the toll-free number on the cover or in the "Assistance or
Service" section.
(, s ,.
The shelves in your refrigerator are adjustable to match your
individual storage needs.
Storing similar food items together in your refrigerator and
adjusting the shelves to fit different heights of items will make
finding the exact item you want easier. It will also reduce the
amount of time the refrigerator door is open, and save energy.
To remove and replace a shelf:
1. Remove items from the shelf.
2. Slide the shelf straight out to the stop.
3. Depending on your model, lift back or front of the shelf past
the stop. Slide shelf out the rest of the way.
4. Replace the shelf by sliding the back of the shelf into the
track in the wall of the cabinet.
5. Guide the front of the shelf into the shelf track. Be sure to
slide the shelf in all the way.
Meat storage guide
Store most meat in original wrapping as long as it is airtight and
moisture-proof. Rewrap if necessary. See the following chart for
storage times. When storing meat longer than the times given,
freeze the meat.
Fresh fish or shellfish .................. use same day as purchased
Chicken, ground beef, variety meats (liver) ............... 1-2 days
Cold cuts, steaks/roasts ........................................... 3-5 days
Cured meats ............................................................ 7-10 days
Leftovers - Cover leftovers with plastic wrap, aluminum foil, or
plastic containers with tight lids.
11
Loading...