Whirlpool YCEP2760KQ2, YCEP2760KQ1, YCEP2760KQ0 Installation Guide

IMPORTANT:

Part No, 8528107

Read and save

these instructions

IMPORTANT
Installer: Leave Installation Instructions

with the owner.

Owner: Keep Installation Instructions for

future reference.

Save Installation Instructions for local

electrical inspector's use.

www.whirlpool.com LAUNDRY

COMMERCIAL

DRYER

ELECTRIC

120-volt, 60 Hz

120/240-volt, 60 Hz

COMMERCIAL

PRODUCTS

®

Before you start...

Your safety and the safety of others are very important.

We have provided many important

safety messages in this manual and
on your appliance. Always read and

obey all safety messages.

You can be killed or seriously

injured if you don't immediately

follow instructions.

This is the safety alert symbol.

This symbol alerts you to

potentialhazards that can kill

or hurtyou and others.

All safety messages will follow the

safety alert symbol and either the word
=DANGER" or "WARNING". These

words mean:

You can be killed or seriously

injured if you don't follow
instructions.

All safety messages will tell you
what the potential hazard is, tell you

how to reduce the chance of injury,
and tell you what can happen if the
instructions are not followed.

WARNING:FOryoursefotythe

informationinthismanualmustbe

followedtominimizetheriskoffire or
explosionortopreventproperty

damage,personalinjuryordeath.

• Donottouchanyelecbicnl

switah;donotuseanyphonein
yourbuilding.

• Cleartheroom,buildingornrseof

nil occupants.

• Immndintalycallyourgassupplier

-- Donotstoreor usegasoline,

orotherflammablevaporsandliquids

inthevicinityofthis oranyother

appliance.

-- WHATTOO0 IFYOUSMELLGAS:

• Donottrytolightanyappliance.

fromnneighbor'sphone.Follow
thegassupplier'sinstructions.

• Ifyoucannotreachyourgas
supplier,callthe firedepartment.

-- Installationandservicemustbe

donebynqualifiedinstaller,
serviceagencyorthegassupplier.

It is your

responsibility to:

Observe allgoverningcodesand
ordinances.

Check code requirements: Some codes

Explosion Hazard

Keep flammable materials and
vapors, such as gasoline, away
from dryer.

Place dryer at least 18 inches

(45.8cm) above the floor for a

garage installation.

Failureto do so can result in death,
explosion, or fire.

If installingaGASdieter:

It is required that the operator post, in a

prominent location, instructions for the
customer's use in the event the

customer smells gas, This information
shall be obtained from your local gas
supplier,

Page 2

limit or do not permit installation of clothes
dryers in garages, closets, or sleeping
quarters, Contact your local building

inspector,

Comply with the installation specifications
and dimensions,

Consider spacing reduirements for
companion appliances,

Make sure you have everything necessary
far proper installation,

Properly install dryer,

Contact a qualified installer to insure that
the electrical and gas installations meet all

national and local codes and ordinances,

Exhaust to outdoors: Dryer must be
exhausted outdoors,

Note: The dryer must not be installed in an
area where itwill be exposed to water

and/or weather,

IMPORTANTSAFELYINSTRUC11ONS

WARNING -- To reduce the riskof fire,
elecldc shock, or injury to persons when

using your appliance, follow basic
precautions, including Ihe following:

1. Read all instructions before using the

appliance,

2. Do not dry articles that have bean
previously cleaned in, washed in,

soaked in, or speffed with gasoline,

dry-cleaning solvents,or other

flammable or explosive substances, as
they give off vapors that could ignite

or explode,

3. Do not allow children to play on or in

the appliance, Close supervision of

children is necessary when the
appliance isused near children,

4. Before the appliance isremoved from

service or discarded, remove the door
to the drying compartment,

5. Do nat reach inte the appliance if the
drum ismoving,

6. Do nat install or stere this appliance

where itwill be exposed to the
weather,

7. Do nat tamper with cantrols,

8. Do not repair or replace any part of

the appliance or attempt any
servicing unless specifically

recommended in the user-
maintenance instructions or in

published user-repair instructions that

you understand and have the skillsto

carry out,

9. Do not use fabric softeners or products

to eliminate static unless

recommended by the manufacturer
of the fabric softener or product,

10. Do not use heat to dry articles
containing foam rubber or similarly

textured rubber-like materials,

11. Clean lint screen before or after each
load,

12. Keep area around the exhaust
opening and adjacent surrounding

areas flee from the accumulation of
lint, dust, and dirt,

13. 11neinteriorof the appliance and
exhaust duct should be cleaned

periodically by qualified service
personnel,

14. Do not place items exposed to
cooking oils in your dryer, Items
contaminated with caokJng oiLsmay

canlTibute to a chemical reaction that
could cause a load to catch fire,

SAVE THESEINSTRUCTIONS

Post the following in a prominent

location.

FOR YOUR SAFEW

Do not store or use gasoline or
other flammable vapors and liquids

in the vicinity of this or any other
appliance.

The console houses the electronic
control board, The board is factory set

for a dry time of 45 minutes, Consult
the Tech Sheet found inside the dryer

toe panel to reset dry time and for
other options,

The coin-slide mechanism, control
panel lock and key, and coin-box lock

and key are not included and are
available from usual industry sources,

Exhaust
requirements

Fire Hazard

Use a heavy metal vent.
Do not use a plastic vent.

Do not use a metal foil vent.
Failure to do so can result in

death or fire,

Do not use non-metal flexible vent,
metal vent that is smaller than four

inches in diameter or exhaust hoods

with magnetic latches,
The dryer must be exhausted

outdoors,

Do not exhaust dryer into a gas vent,
chimney, wall, ceiling, or concealed
space of a building,

Do not install flexible vent in enclosed
walls, ceilings or floors,

If using an existing exhaust system,
clean lint from entire length of exhaust
system, Make sure exhaust hood is not

plugged with lint,
The exhaust system should be

inspected and cleaned yearly,

Replace any plastic or metal foil
exhaust vent with rigid metal or

flexible metal vent,

Use 4" (10,2 cm) vent clamps to

secure vent system,

exhaust airflow

better r_ good _=1

Four-inch (10.2 cm) metal exhaust
vent isrequired, Plan installation to

use the fewest number of elbows and
turns,

Metal flexible vent must be fully
extended and supported when the
dryer isin its final position, DO NOT

KINK OR CRUSH THEVENT, The metal

flexible vent must be completely

open to allow adequate exhaust air
to flow.

Allow as much room as possible

when using elbows or making turns,

Bend vent gradually to avoid kinking,
Remove excess flexible vent to avoid

sagging and kinking that may result in
reduced air flow,

Exhaust outlet is located at the
center of the boftom dryer back,

The exhaust vent can be routed up,

down, left, right, behind the dryer or
straight out the back of the dryer,

Maximum length of exhaust system
depends upon the type of vent used,
number of elbows and type of
exhaust hood, The maximum length
for both rigid and flexible vent is

shown in the chart,

EXHAUSTHOOD TYPE

4_ r

of90°

.o,

turm

(I (10=c_ 1_ c_)

MAXIMUM LENGTH OF&-INCH (I 0.2 cm) DIAMEilER

O 64FT.(19.5m) 64FT.(19.5m) 58FT.(17.7m)

I 54FT.(16.5m) 54FT.(16.5m) 48FT.(14.6m)

2 44 FT.(13.4 m) 44 FT.(13"4 m) 38 FT.(11.6 m)

3 35FT.(10.7m) 35FT.(10.7m) 29FT.(8.8m)
4 27FT.(8.2 m) 27FT.(8.2 m) 21FT.(6,4 m)

MAXIMUMLENG1HOF4-INCH(10.2cm)DIAMElSR

O 36 FT.(11.0 m) 36 FT.(ll.a m) 28 FT.(8.5 m)
1 31 FT.(9.4 m) 31 FT.(9"4 nO 23FT.(7.0 m)

2 27FT.(8.2m) 27FT.(8.2m) 19FT.(5.8m)

3 25 FT.(7.6 m) 28FT.(7.6 nO 17 FT.(5.2 m)

4 23FT.(7.am) 23 FT.(7.0 nO 18FT.(4.6 m)

RIGIDMETALVENT

FLI'_(IBLEMErALVENT

For exhaust systems not covered by
the exhaust length chart, see
Whirlpool Service Manual, "Exhausting
Whirlpool Dryers," Part No, 603197,
available from your Whirlpool parts

distributor,

The dryer must be exhausted to the
outside and provisionmade for

enough airforcombustion and
ventilation,(Check governing codes

and ordinances,) See °Recessed area
and closet installation instructions" on

Page 12,
An exhaust hood should cap the

exhaust vent to prevent exhausted air
from returning into the dryer, The

outlet of the hood must be at least

12 inches (30,5 cm) from the ground
or anything else that may be in the
path of the exhaust,

Four-inchoutlethood ispreferred.

However,a 2-I12-inch(6,4cm) outlet
exhausthood may be used,A
2-I/2-inch(6,4cm) outletcreates
greaterback pressurethan other
hood types,Forpermanent

installation,a stationaryexhaust
systemisrequired,

Page 3

A main exhaust vent can be used for

exhausting a group of dryers, Main
exhaust vent should be sized to

remove 200 CFM of air per dryer,
Large-capacity lint screens of proper

design may be used in the main
exhaust vent if checked and cleaned

frequently, The room where the dryers
are located should have make-up air
equal to or greater than the CFM of
all the dryers in the room,

alrnow _ ma[ncole_ot'vent -4_

Back-draft Damper Kits, Part No,

339191 B, are available from your
Whirlpool dealer and should be
installed in each dryer's exhaust vent
to prevent exhausted air from
returning into the dryers and to keep

the exhaust in balance within the
main exhaust vent, Unobstructed air

openings are required,
Each exhaust vent should enter the

main vent at an angle pointing in the
direction of the airflow, Vents entering
from the opposite side should be
staggered to reduce the exhausted
air from interfering with the other

vents,
The maximum angle of each vent

entering the main vent should be no
more than 30°,

Keep air openings free of dry
cleaning fluid fumes. Fumes create
acids which, when drawn through the
dryer heating units, can damage
dryers and loads being dried.

A clean-out cover should be located
on the main exhaust vent for

periodically cleaning of the exhaust
system,

An exhaust hood should cap the
outside end of the main vent to

prevent exhausted air from returning

to the dryers, If an exhaust hood
cannot be used, the outside end of

the main duct should have a sweep
elbow directed downward, Ifthe

main vent travels vertically through

the roof, rather than through the wall,

install 180 ° sweep elbow on the end
of vent at least 2 feet (61 cm) above
the highest part of the building, The
opening wall or roof shall have a
diameter 1/2 inch (1,3 cm) larger than

the exhaust vent diameter, The
exhaust vent should be centered in

the opening,

exhaull

hood or -_( wall

main exhaull vent

U.°°T,a-

wall

180°

2ft. (61 cm) I--_ _/elbow
min. above

highestpoint of

building main collector

Do Not install screening or cap over

end of vent,

_Neop

vent

Gas requirements

Explosion Hazard

Use a new AGA or CSA

approved gas supply line.

Install a shut-off valve.

Securely tighten all gas
connections.

If connected to LP, have a

qualified person make sure gas

pressure does not exceed t3"
(33 cm) water column. Examples

of a qualified person include

licensed heating personnel,

authorized gas company

personnel, and authorized

service personnel.

Failure to do so can result in

death, explosion, or fire.

OBSERVEALLGOVERNINGCODES
AND ORDINANCES.

An This installation must conform

with local codes, or in absence of

local codes with the National Fuel

Gas Code ANSI Z223,1/NFPA 54 or the
CAN/CGA - B149 installation codes,

B n The design of this dryer has
been certified by the CSA

International for use at altitudes up to
10,000 feet (3048 m) above sea level

at the B,T,U, rating indicated on the

model/serial plate, Burner input
adjustments are not required when
the dryer is operated up to this

elevation,
When installed above 10,000 feet

(3048 m), a four percent (4%)

reduction of the burner B,T,U, rating
shown on the model/serial plate is

required for each 1,000 foot (305 m)

increase in elevation, For assistance
when converting to other gas types

and/or installing above 10,000 feet
(3048 m) elevation, contact your

local service company,

Page 4

Cm Check that dryer is equipped

with the correct burner for the
particular type of gas used, Burner

information can be found on the

serial/rating plate in the door well of
the appliance, If this information does

not agree with the type of gas

available, see your dealer,

D mThis dryer is equipped for use

with NATURAL GAS, It is certified by
CSA International for manufactured,

mixed and L,P, (propane and
butane) gases with appropriate

conversion, No affempt shall be

made to convert the appliance from

the gas specified on the serial/rating
plate for use with a different gas
without consulting the serving gas
supplier, Conversion must be done by

a qualified service technician. Gas
conversion kit part numbers are listed

on the gas valve burner base.

E mProvide a rigid gas supply line of

I/2-inch IPSpipe to the dryer

location, If the total length of the
supply line is more than 20 feet
(6,1 m), larger pipe will be needed,

For L,P, gas usage, 3/8-inch,
approved copper tubing may be
used, Pipe-joint compounds suitable
for use with L,P, gas should be used,

shutoffvalve

_"open" position

gas supply

FmThe supply line shall be equipped

with a shutoff valve installed within 6
ft, (1,8 m) of dryer in accordance with

the National Fuel Gas Code, ANSI
Z223,1 -- latest edition*, In Canada,

an individual manual shutoff valve

must be installed in accordance with
the B149 installation codes CAN/CGA

B149,1 and CAN/CGA B149,2*, This
valve should be located in the same

room as the dryer and should be in a

location that allows ease of opening
and closing, Do Not block access to

the shutoff valve,

G mIf the dryer isinstalled in a
confined area such as a bathroom or

closet, provision must be made for
enough air for combustion and

ventilation, (Check governing codes
and ordinances, or refer to the

section of this instruction covering

recessed and closet installations,)

H m If local codes and ordinances

permit, it is recommended that new
flexible gas connector, design-
certified by the AGA or CSA, be used
for connecting the dryer to the gas
supply line, (The gas feed pipe which
extends through the lower rear of the
dryer isprovided with 3/8-inch metal
pipe thread,)

oom ,nat,o o p,p f,ft,ngsmust

be used to obtain an in-line
connection to the dryer,

J m Make sure that lower edges of
the cabinet, plus the back and

boffom sides of the dryer are free of
obstructions to permit adequate
clearance of air openings for

combustion air, See "Recessed area
and closet installation instructions,"

Page 12, for minimum spacing
requirements,

Km For ease of installation,

operation and servicing (if ever
needed) adequate space should be
provided around the dryer,

Lm A 1/8-inch NPT plugged tapping,

accessible for gauge testing, must be
installed immediately upstream of the
gas supply connection to the dryer,

The dryer must be disconnected from
the gas supply piping system during
any pressure testing of the system at
test pressures in excess of 1/2 psig,

The dryer must be isolated from the gas
supply piping system by closing the

equipment shut-off valve during any
pressure testing of the gas supply piping

system at test pressures equal to or less

than 1/2 psi (3,45 kPa),

ElectzCcal
requirements

Electrical Shock Hazard

Plugintoa grounded3-prongoutlet.
Donot removegroundprong.

Donot useanadapter.
Donot useanextensioncord.

Failureto followthese insbucttons

can result indeath,fire, orelectrical
shock.

A 12B-volt, 6O-Hz, AC-only, 15-or
2B-ampere fused electrical supply is

required, A time-delay fuse or circuit
breaker is recommended,

It is recommended that a separate

circuit serving only this appliance be
provided,

If codes permit and a separate ground

wire is used, it is recommended that a
qualified electrician determine that the
ground path is adequate.

Recommended
ground method

The dryer, when installed, must be
electrically grounded in accordance

with local codes, or in the absence of

local codes, with the National

Electrical Code, ANSI/NFPA 70**, or
the Canadian Electrical Code, CSA
C22,1",

GROUNDING INSTRUCTIONS: This
appliance must be grounded, In the
event of malfunction or breakdown,
grounding will reduce the risk of

electric shock by providing a path of

least resistance for electric current,
The power supply cord plug must be

plugged into an appropriate outlet
that isproperly installed and
grounded in accordance with all

local codes and ordinances,
WARNING - Improper connection of

the equipment-grounding conductor
can result in a risk of electric shock,

Check with a qualified electrician or
serviceman if you are in doubt as to
whether the appliance isproperly
grounded, Do not modify the plug
provided with the appliance - if it will

not fit the outlet, have a proper outlet

installed by a qualified electrician,

3-prong
outlet

3-pron_l _
grouna ,K-._/7...-_I_

0u°

power /

supply cord ground

Copies of the standards listed above may
be obtained from:

* CSA International

8501 East Pleasant Valley Road
Cleveland, Ohio 44131 _5575

** National Fire Protection Association

One Balterymarch Park
Quincey, Massachuselfs 02269

prong

Important: Observe all governing
codes and ordinances. Page 5

Now Start...

With dryer in laundry area.

Excessive Weight Hazard

Usetwo or morepeopleto moveand
installdryer.
Failureto do so can resultin back or

otherinjury.

3-prong,
ogru_J_d'IypO

_ I _ oxhould vent

I, 1

i fS 1

J,_ I .

-" _ I 1 gas supply Ime

gasshuloffvalve

l mTake tape off front corners of

dryer, Open dryer and remove the

literature and parts packages, Wipe
the interior of the drum thoroughly
with a damp cloth,

mTake two of the cardboard

corners from the carton and place
them on the floor in back of the dryer,

Firmly grasp the body of the dryer
and gently lay it on its back on the
cardboard corners,

mWith one of the legs in hand,

check the ridges for a diamond

marking, That's how far the leg is
supposed to go into the hole,

mStaff to screw the leveling legs

into the holes by hand, (Use a small
amount of liquid detergent to

lubricate the screw threads so it is
easier to turn the legs,) Use a 1-inch

wrench or socket wrench to finish
turning the legs until you reach the

diamond mark,

Now stand the dryer up,

Slide dryer onto cardboard or

hardboard before moving across floor
to avoid damaging floor covering.

/

Electrical Shock Hazard

Disconnect power before

servicing.

Replace all parts and panels
before operating.
Failure to do so can result in

death or electrical shock,

mRemove the service door of the

meter case, Lift

the service door \ _ _

up at the back

and remove,

Install money-

accepting
device, (Refer to

manufacturer's
instructions for proper installation,)

For dryers using coin slides, use

adapter kit supplied with dryer,

Replace the meter case service door,
Put the coin vault with lock and key

the meter case opening,

mMove dryer close to final

position, Remove cardboard or
hardboard from under dryer,

mRemove red cap from gas pipe,

Carefully move dryer into final
position, Place level on top of the

dryer, first side to side; then front to

back, If the dryer is not level, adjust
the legs of the dryer up or down until
the dryer is level,

mConnect gas supply to dryer,

Use pipe-joint compound resistant to
the action of L,P, gas for gas
connections, If flexible metal tubing is

used, be certain there are no kinks,

If necessary for service, open the toe

panel, use a putty knife to press on
the toe panel lock located at the
center top of the toe panel, Pull
downward on the toe panel to open,
Toe panel ishinged at the bottom,

mOpen the shutoff valve in the

gas supply line,

0 • Use a non-corrosive leak

detection fluid to check for leaks,
Bubbles around connections will

indicate a leak, If a leak appears,

shut off gas valve controls and adjust

connections, Then check
connections again, Close toe panel,

All connections must be wrench-
tightened.

1 • To exhaust dryer, see Exhaust

requirements, Pages 3-4, Connect

exhaust vent system to dryer exhaust
outlet and exhaust hood using 4"
(10,2 cm) clamps, Use caulking to

seal exterior wall opening around
exhaust hood,

2. Carefully move dryer into

final position, Place level on top of
the dryer, first side to side; then front
to back, If the dryer is not level, adjust
the legs of the dryer up or down until
the dryer is level,

3 • Plug power supply cord into

grounded outlet,

4. Check dryer operation (some

accumulated time may be on the
timer due to factory testing),

Insert coins in slide and press slide in
slowly, (Operating time will
accumulate per number of coins and
type of timing cam used,) Push
START/RESTARTbutton, Using a full
heat cycle (not the air cycle), let the
dryer run for at least five minutes,

Dryer will stop when time isused up,
Note: Dryer door must be closed for

dryer to operate, When door is open,
dryer stops, but timer continues to run,
To restart dryer, close door and push

START/RESTARTbutton,

5 • If the burner does not ignite

and you can feel no heat inside the
dryer, shut off dryer for five minutes,

Check that all supply valve controls
are in "ON" position and that the

electrical cord is plugged in, Repeat
five-minute test,

6. If drying time is too long,

make sure lint screen is clean,

Page 6

Electrical

Now Start...

requirements

If codes permit and a separate
ground wire is used, it is
recommended that a qualified
electrician determine that the ground
path isadequate.

Important: Observe all governing

codes and ordinances.
A four-wire or three-wire (Canada:

four-wire only), single-phase, 1201240-
volt, 60-Hz, AC-only electrical supply

(or four-wire or three-wire, 120/208-
volt, if specified on the model/serial

rating plate) is required on a
separate, 30-ampere circuit, fused on

both sides of the line, A time-delay
fuse or circuit breaker is

recommended,

Recommended
ground method

In U.S.:

It is the personal responsibility and
obligation of the customer to contact
a qualified electrician to assure that
the electrical installation isadequate

and in conformance with the

National Electrical Code, ANSI/NFPA
70", and all local codes and
ordinances,

In Canada:

It isthe personal responsibility and
obligation of the customer to
install the dryer in accordance

with CAN 1-B149 installation
codes** and all national or local

codes.
Canadian models are equipped

with a four-wire, 30-amp rated
flexible-type power cord. The
power cord must be plugged into
a mating 30-amp receptacle.
(NEMA type 14-30R).

Copies of the standards listed above may
be obtained from:

* National Fire Protection Association

One Baited/march Park
Quincy, Massachusetts 02269

**CSA International

8501 East Pleasant Valley Road
Cleveland, Ohio 44131 _75

Excessive Weight Hazard

Use two or more people to move

and install dryer.

Failure to do so can result in
back or other injury.

With dryer in laundry area...

vent

sylle

exhaust_

l mTake tape off front corners of

dryer, Open dryer and remove the

literature and parts packages, Wipe

the interior of the drum thoroughly
with a damp cloth,

mTake two of the cardboard

corners from the carton and place
them on the floor in back of the dryer,

Firmly grasp the body of the dryer

and gently lay it on its back on the
cardboard corners,

mWith one of the legs in hand,

check the ridges for a diamond

marking, That's how far the leg is

supposed to go into the hole,

mStaff to screw the leveling legs

into the holes by hand, (Use a small

amount of liquid detergent to

lubricate the screw threads so it is

easier to turn the legs,) Use a 1-inch
wrench or socket wrench to finish

turning the legs until you reach the
diamond mark,

Now stand the dryer up,

Slide dryer onto cardboard or

hardboard before moving across floor

to avoid damaging floor covering.

'u:_°nnectbox

Electrical Shock Hazard

Disconnect power before

servicing,

Replace all parts and panels
before operating,
Failure to do so can result in
death or electrical shock,

mRemove the service door of the

meter case, Lift
the service door
up at the back

and remove,

Install money-
accepting

device, (Refer to

manufacturer's

instructions for proper installation,)

For dryers using coin slides, use
adapter kit supplied with dryer,

Replace the meter case service
door, Put the coin vault with lock and

key the meter case opening,

mMove dryer close to final

position, Remove cardboard or
hardboard from under dryer,

Page 7

7 • U.S. installations:

Make electrical connection,

Thisdryer is manufactured with the
cabinet-ground conductor
connected to the NEUTRAL(center) of
the wiring harness at the terminal
block. If local codes do NOT permit
this type of connection, use "Four-

wire connection" instructions.
For a grounded, cord-connected

appliance --

GROUNDING INSTRUCTIONS:
This appliance must be grounded, In

the event of malfunction or

breakdown, grounding will reduce
the risk of electric shock by providing
a path of least resistance for electric

current,

If using a power supply cord, the plug

must be plugged into an appropriate
outlet that is properly installed and
grounded in accordance with all

local codes and ordinances,
WARNING - Improper connection of

the equipment-grounding conductor
can result in a risk of electric shock,

Check with a qualified electrician or
serviceman if you are in doubt as to

whether the appliance isproperly
grounded, Do not modify the plug
provided with the appliance - if it will

not fit the outlet, have a proper outlet

installed by a qualified electrician,

For a permanently connected
appliance --

GROUNDING INSTRUCTIONS:
This appliance must be connected to

a grounded metal, permanent wiring
system; or an equipment-grounding

conductor must be run with the
circuit conductors and connected to

the equipment-grounding terminal or

lead on the appliance,

Canadian installations:

For a grounded, cord-connected
appliance --

GROUNDING INSTRUCTIONS:
This appliance must be grounded, In

the event of malfunction or

breakdown, grounding will reduce
the risk of electric shock by providing
a path of least resistance for electric

current,
This appliance isequipped with a

cord having an equipment-grounding
conductor and a grounding plug, The
plug must be plugged into an
appropriate outlet that isproperly

installed and grounded in
accordance with all local codes and

ordinances,

Page 8

WARNING -Improper connection of
the equipment-grounding conductor

can result in a risk of electric shock,

Check with a qualified electrician or
service representative or personnel if
you are in doubt as to whether the
appliance is properly grounded, Do

not modify the plug provided with the
appliance - if it will not fit the outlet,

have a proper outlet installed by a
qualified electrician,

Power supply cord

(u.s. oaiy)

Use a new UL-approved power supply
cord rated 240-volt rain., 30 amperes

and marked for use with a clothes
dryer.

Fire Hazard

Use a new UL approved 30

ampere power supply cord.

Use a UL approved strain relief.
Disconnect power before making

electrical connections.
Connect neutral wire (white or

center wire) to center terminal

(silver).

Ground wire (green or bare wire)

must be connected to green

ground connector.
Connect remaining 2 supply

wires to remaining 2 terminals

(gold).

Securely tighten all electrical
connections.

Failure to do so can result in

death, fire, or electrical shock.

91tactwire (o.s. o y)

Fire Hazard

Use 10-gauge solid copper wire.
Use a UL approved strain relief.
Disconnect power before making

electrical connections.
Connect neutral wire (white or

center wire) to center terminal

(silver).

Ground wire (green or bare wire)

must be connected to green

ground connector.
Connect remaining 2 supply

wires to remaining 2 terminals

(gold).

Securely tighten all electrical
connections.

Failure to do so can result in

death, fire, or electrical shock.

1• Disconnect the power supply.

external ground

_//_ductor screw

__"'1 hold-

jno, I/d°wn

_ screw

2. Remove hold-down screw
and terminal block cover,

strain _dryer
relief _ \cabinet

clamp ¢!,diL _ ?
sections..__._ /

3. Assemble _; _stroinrelief

3/4" U,L,-listed screws
strain relief (U,L, marking on strain relieT_

into the hole below terminal block

opening, Tighten strain relief screws just
enough to hold the two clamp
sections together, Install power supply
cord/cable through the strain relief,

Complete installation following
instructions for your type of

connection:

• Four-wire (recommended method)

• Three-wire (iftour-wire is not

available)