WHIRLPOOL XW29000VJ User Manual
LAUNDRY WORKSURFACE USE AND CARE GUIDE
BUANDERIE - GUIDE D’UTILISATION ET D’ENTRETIEN
LAVANDERÍA - MANUAL DE USO Y CUIDADO
Table of Contents
WORKSURFACE SAFETY .............................................. 2
INSTALLATION REQUIREMENTS .................................. 2
Tools and Parts .................................................................. 2
LOCATION REQUIREMENTS ............................................. 2
INSTALLATION INSTRUCTIONS ........................................ 3
WORKSURFACE CARE ........................................................ 4
WARRANTY............................................................................. 4
Table des matières
SÉCURITÉ DE LA SURFACE DE TRAVAIL .................... 5
EXIGENCES D’INSTALLATION ......................................5
Outils et pièces .................................................................. 5
EXIGENCES D’EMPLACEMENT ........................................ 5
INSTRUCTIONS D’INSTALLATION ............................... 6
ENTRETIEN DE LA SURFACE DE TRAVAIL .................. 7
GARANTIE ....................................................................... 8
Índice
SEGURIDAD DE LA SUPERFICIE DE TRABAJO .......... 9
REQUISITOS DE INSTALACIÓN .................................... 9
Herramientas y piezas ...................................................... 9
REQUISITOS DE UBICACIÓN ........................................ 9
INSTRUCCIONES DE INSTALACIÓN ............................ 10
CUIDADO DE LA SUPERFICIE DE TRABAJO .............. 11
GARANTÍA ....................................................................... 12
W10101296C
WORKSURFACE SAFETY
INSTALLATION REqUIREMENTS
TOOLS AND PARTS
Gather the required tools and parts before starting installation.
Tools needed:
Worksurface dimensions:
Top view:
Tape measure
Level
LOCATION REqUIREMENTS
The worksurface can be installed on top of a front-loading washer
and dryer pair situated next to each other. The washer and dryer
must be level side to side and front to back and at the same
height. Proper installation is your responsibility.
Installation Spacing:
The worksurface will t on top of a washer and dryer that are
each 27" (686 mm) wide and have a spacing of approximately
1" (25 mm) between them for the alignment pads.
Bottom view:
NOTE: The worksurface will add 3" (76 mm) to the overall height
of your washer and dryer.
2
INSTALLATION INSTRUCTIONS
3. Put worksurface into place
Seam
1. Check washer and dryer spacing
NOTE: Before you begin, set aside the rolled-up rubber mat
that came with your worksurface until later.
Check the spacing between your washer and dryer.
If necessary, move your washer or dryer so that there
is a space of approximately 1" (25 mm) between them.
2. Check washer and dryer levelness
Place the worksurface on top of the washer and dryer. Align
the front edge of the worksurface with the seam between the top
of the washer/dryer and the control panel. Center it left to right
so that the alignment pads t in the space between the washer
and dryer.
4. Put rubber mat in place
Check that the top of the washer and the bottom of the rubber
mat are clean and set mat in place on top of the worksurface.
IMPORTANT: Dispose of/recycle all packaging materials.
Check that the washer and dryer are level front to back and side
to side and the difference in height is no more than 3/8" (9.5 mm).
Place a level on both the washer and dryer to determine any
difference in height. If necessary, see the Installation Instructions
that came with your washer and dryer to properly adjust the
leveling feet.
Not Level LEVEL Not Level
3
WHIRLPOOL CORPORATION LAUNDRY WARRANTY
LIMITED WARRANTY
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or
furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter “Whirlpool”) will pay for Factory Specied Parts
and repair labor to correct defects in materials or workmanship that existed when this major appliance was purchased. Service must be
provided by a Whirlpool designated service company. YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY
SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. This limited warranty is valid only in the United States or Canada and applies
only when the major appliance is used in the country in which it was purchased. Proof of original purchase date is required to obtain
service under this limited warranty.
ITEMS EXCLUDED FROM WARRANTY
This limited warranty does not cover:
1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is
used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.
2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or
repair house fuses, or to correct house wiring or plumbing.
3. Service calls to repair or replace appliance light bulbs, air lters or water lters. Consumable parts are excluded from warranty
coverage.
4. Damage resulting from accident, alteration, misuse, abuse, re, ood, acts of God, improper installation, installation not in
accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.
5. Cosmetic damage, including scratches, dents, chips or other damage to the nish of your major appliance, unless such damage
results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase.
6. Pick up and delivery. This major appliance is intended to be repaired in your home.
7. Repairs to parts or systems resulting from unauthorized modications made to the appliance.
8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an
authorized Whirlpool servicer is not available.
9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance
with Whirlpool’s published installation instructions.
10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or
cannot be easily determined.
DISCLAIMER OF IMPLIED WARRANTIES
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR
A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces
do not allow limitations on the duration of implied warranties of merchantability or tness, so this limitation may not apply to you. This
warranty gives you specic legal rights, and you also may have other rights that vary from state to state or province to province.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow
the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This
warranty gives you specic legal rights, and you also may have other rights that vary from state to state or province to province.
If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies.
If you think you need repair service, rst see the “Troubleshooting” section of the Use & Care Guide. If you are unable to resolve the
problem after checking “Troubleshooting,” additional help can be found by checking the “Assistance or Service” section or by calling
Whirlpool. In the U.S.A., call
. In Canada, call 80/7.
WORKSURFACE CARE
The worksurface can be used for sorting, treating, and folding
laundry and for storing various laundry products.
IMPORTANT: The worksurface is not intended for ironing.
Using an iron on the worksurface could cause it to become
discolored.
Cleaning Your Worksurface:
To keep your worksurface clean, follow this recommended
cleaning procedure:
1. Use a soft damp cloth or sponge to wipe up any spills.
Occasionally wipe the worksurface to keep it looking new.
2. Use a mild soap and water or a household cleaner
and a soft brush on the worksurface. Do not use abrasive
products.
4
Loading...