Whirlpool XPSG User Manual

CONNECTED APPLIANCE INFORMATION

Federal Communications Commission (FCC) Compliance Notice

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one of the following
measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause
undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could
void the user‟s authority to operate the equipment.

RF Exposure Information

To comply with FCC/IC RF exposure requirements for mobile transmitting devices, this
transmitter should only be used or installed at locations where there is at least 20cm separation
distance between the antenna and all persons.

To comply with FCC/IC RF exposure limits for general population/uncontrolled exposure, the
antenna(s) used for this transmitter must be installed to provide a separation distance of at least
20 cm from all persons and must not be co-located or operating in conjunction with any other
antenna or transmitter

CONNECTED APPLIANCE INFORMATION

Industry Canada (IC) Compliance Notice

This Device complies with Industry Canada License-exempt RSS standard(s). Operation is
subject to the following two conditions:

1. This device may not cause interference,

2. This device must accept any interference, including interference that may cause

undesired operation of the device.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of
a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To
reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary
for successful communication.

To comply with FCC and Industry Canada RF radiation exposure limits for general population,
the antenna(s) used for this transmitter must be installed such that a minimum separation
distance of 20 cm is maintained between the radiator (antenna) and all persons at all times and
must not be co-located or operating in conjunction with any other antenna or transmitter.

Le présent appareil est conforme aux CNR d„Industrie Canada applicables aux appareils radio
exempts de licence. L„exploitation est autorisée aux deux conditions suivantes:

(1) l„appareil ne doit pas produire de brouillage, et
(2) l„utilisateur de l„appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d„en compromettre le fonctionnement.

Conformément à la réglementation d„Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d„un type et d„un gain maximal (ou inférieur) approuvé pour
l„émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique
à l„intention des autres utilisateurs, il faut choisir le type d„antenne et son gain de sorte que la
puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l„intensité nécessaire à
l„établissement d„une communication satisfaisante.

Pour satisfaire aux exigences de la FCC et IC d‟exposition aux radiofréquences, une distance de
séparation de 20 cm ou plus doit être maintenue entre cet appareil et des personnes lors de
fonctionnement du dispositif. Pour assurer la conformité des opérations au plus près que cette
distance n‟est pas recommandée. L‟antenne utilisée pour ce transmetteur ne doit pas être co­localisés en conjonction avec toute autre antenne ou transmetteur.