15.5" PEDESTAL INSTALLATION INSTRUCTIONS
For use only with front load washers and dryers
INSTRUCTIONS D’INSTALLATION DU PIÉDESTAL DE 15,5"
Pour utilisation avec les produits suivants seulement
laveuses et sécheuses à chargement par l’avant
Para una versión de estas instrucciones en español, visite www.whirlpool.com
Table of Contents
PEDESTAL SAFETY .....................................................1
INSTALLATION REQUIREMENTS ..............................2
Location Requirements .........................................2
Tools and Parts ......................................................2
INSTALLATION INSTRUCTIONS .................................3
Before Installing Pedestal .....................................3
INSTALLING THE PEDESTAL ...............................................5
COMPLETE THE INSTALLATION ..........................................6
WARRANTY ............................................................................8
INSTALLATION NOTES
Date of purchase: _________________________________
Date of installation: _______________________________
Installer: ________________________________________
Model number: ___________________________________
Serial number: ___________________________________
PEDESTAL SAFETY
SÉCURITÉ DU PIÉDESTAL .........................................9
EXIGENCES D’INSTALLATION ...................................9
Exigences d’emplacement ....................................9
Outillage et pièces .................................................9
INSTRUCTIONS D’INSTALLATION ...........................10
Avant l’installation du piédestal ..........................10
INSTALLATION DU PIÉDESTAL ................................12
ACHEVER L’INSTALLATION
GARANTIE ..................................................................16
NOTES CONCERNANT L’INSTALLATION
Date d’achat : _____________________________________
Date d’installation : ________________________________
Installateur : ______________________________________
Numéro de modèle : ________________________________
Numéro de série : __________________________________
Table des matières
.....................................14
W10178071B
W10348601B - SP
INSTALLATION REQUIREMENTS
LOCATION REQUIREMENTS
Additional Items Needed:
Towel Sponge
Parts Supplied:
NOTE: If the washer/dryer and pedestal assembly are located in
a garage, 3" (76 mm) must be added under the pedestal so that
the washer/dryer is 18" (458 mm) above the garage oor.
TOOLS AND PARTS
Gather the required tools and parts before starting installation.
Tools Needed:
Utility knife 1/4" hex-head ratchet
or open-end wrench
Four #12 x 5/8" hex-head Drawer divider
sheet metal screws
Level 9/16" open-end wrench
Pliers or slip-joint pliers Bucket
1/4" nut driver
or nut driver
2
5/16" hex-head ratchet
INSTALLATION INSTRUCTIONS
BEFORE INSTALLING PEDESTAL
IMPORTANT: If your washer and dryer are already installed, they
must be uninstalled.
Uninstalling your washer
To avoid possible damage to the washer, the transport bolts on
the back of the washer must be in place before installing the
pedestal. For more information on transport bolts, see “Remove
Transport System” in washer Use and Care Guide.
NOTE: If the washer is to be transported, call your local service
center. To avoid suspension and structural damage, your
washer must be properly set up for relocation by a certied
technician.
1. Turn off the hot and cold water faucets.
2. Unplug the power supply cord.
3. Slowly loosen the ll hoses at the faucets to relieve the water
pressure. Use a sponge or towel to absorb the released water.
4. Remove the “HOT” and “COLD” ll hoses from the back of
the washer. Drain the water from the hoses into a bucket.
5. Remove the drain hose from the standpipe or laundry tub and
drain any water remaining in the hose into a bucket.
6. Pull the washer away from the wall so it can be tipped on its
back.
7. To avoid oor damage and ease of installation and handling,
unfold the empty pedestal box at and place it next to the
washer. Lay the washer on its back (make sure that the power
supply cord is not under the washer) so that the cardboard is
under the entire lower back edge of the washer.
8. An additional small amount of water will drain out of the
washer when it is tipped back. See “Installing the Pedestal”.
Uninstalling your electric dryer
1. Unplug the power supply cord or disconnect wiring if dryer is
direct wired.
2. Pull the dryer away from the wall enough to loosen the vent
clamp. Loosen the clamp and gently remove the exhaust vent
from the dryer exhaust outlet.
3. Pull the dryer away from the wall so that it can be tipped on
its back.
4. To avoid oor damage and ease installation and handling,
unfold the empty pedestal box at and place it next to the
dryer. Lay the dryer on its back (make sure that the power
supply cord is not under the dryer) so that the cardboard is
under the entire lower back edge of the dryer. See “Installing
the Pedestal”.
Uninstalling your gas dryer
1. Unplug the power supply cord or disconnect power.
2. Turn off the gas supply.
3. Pull the dryer away from the wall enough to loosen the vent
clamp. Loosen the clamp and gently remove the exhaust vent
from the dryer exhaust outlet.
4. Disconnect the exible gas supply line from the dryer. Put a
piece of tape over the open ends of the gas line connection
ttings.
5. Pull the dryer away from the wall so that it can be tipped on
its back.
6. To avoid oor damage and ease installation and handling,
unfold the empty pedestal box at and place it next to the
dryer. Lay the dryer on its back (make sure that the power
supply cord is not under the dryer) so that the cardboard is
under the entire lower back edge of the dryer. See “Installing
the Pedestal”.
3
Installation of new washer/dryer
If your washer/dryer is still in the packaging:
Washer/Dryer still in packaging
Conrm transport bolts are in place
NOTE: Transport bolts are only in washers.
Washer
Cut packaging as follows:
Washer: Cut plastic lm along dotted cut line around the
base. Do not remove the packaging. Locate the transport
bolts on rear of washer. Transport bolts must remain in washer
while pedestal is installed. When laying the washer on its back,
hold the bottom cap down on the oor. Do not remove the
plastic lm, corner posts, or top cap.
Dryer: Cut carton around top and down corners along dotted
cut lines. Lay all four carton sides on oor. Discard carton top
and corner posts.
Dryer
4
Hex-head screw
Drawer slide
INSTALLING THE PEDESTAL
Follow these instructions to install the pedestal on a washer or
dryer.
1. Empty pedestal drawer
3. Remove pedestal drawer
Using a 1/4" nut driver, remove the hex-head screws from
both drawer slides and save screws. Remove the drawer
from the slides and set aside. Push the slides back into
the pedestal.
4. Prepare the washer/dryer
Open the pedestal drawer as far as possible and remove the
contents. The package contains four #12 x 5/8" hex-head
sheet metal screws and a drawer divider.
2. Locate spacer pads
The four spacer pads are installed on the top of the pedestal.
These pads reduce vibration between the pedestal and the
washer/dryer.
Washer Bottom
Partially install two of the #12 x 5/8" hex-head sheet metal
screws in the lower holes. Leave a space of about 3/8" (10 mm)
between the screw head and the bottom of the washer/dryer.
NOTE: If your washer/dryer has feet installed, remove them.
Dryer Bottom
5