Whirlpool WTW6400SW3, WTW6600SB2, WTW6600SB3, WTW6600SG2, WTW6600SG3 Owner’s Manual

...

CABRIOTMAUTOMATIC

WASHER WITH

6TH SENSETM

TECHNOLOGY

For questions about features, operation/performance,

parts, accessories or service call: 1-800-253-130t

In Canada, call: 1-800-807-6777

www.whirlpool.com or www.whirlpool.ca

or visit our website at

[AVADO£_

AUTOMATICACABRIOTM

CON TECNOLOGIA

6TH SENSETM

Si tiene preguntas respecto alas caracterfsticas, funcionamiento,

rendimiento, partes, accesorios o servicio tecnico, Ilame al:

En Canadfi, Ilame al: f-800-807-6777

www.whirlpool.eom o www.whirlpool.ea

1-800-253-130t

o visite nuestro sitio web en

W10113000A

LAVEUSE

AUTOMATIQUE

CABRIOTMAVEC

TECHNOLOGIE

6THSENSETM

Au Canada, pour assistance, installation ou service, composer le :

Table of Contents/Jndice/Table des matieres ..2

1-800-807-6777

ou visiter notre site internet h

www.whirlpool.ca

WOO[ MARK

TABLEOFCONTENTS

WASHER SAFETY .......................................................................... 3

INSTALLATION REQUIREMENTS ................................................ 4

Tools and Parts ............................................................................ 4

Location Requirements ................................................................ 5

Drain System ................................................................................ 5

Electrical Requirements ............................................................... 6

INSTALLATION INSTRUCTIONS .................................................. 7

Before You Start ........................................................................... 7

Remove Shipping Base and Packing Ring .................................. 7

Connect Drain Hose ..................................................................... 7

Connect the Inlet Hoses ............................................................... 8

Secure the Drain Hose ................................................................. 9

Level the Washer .......................................................................... 9

Complete Installation ................................................................. 10

BENEFITS AND FEATURES ........................................................ 11

WASHER USE ............................................................................... 12

Starting Your Washer ................................................................. 12

Using the Proper Detergent ....................................................... 12

Pausing or Restarting the Washer ............................................. 13

Stopping the Washer ................................................................. 13

Changing Cycles, Modifiers and Options .................................. 13

Status Lights .............................................................................. 14

Cycles ......................................................................................... 14

Modifiers ..................................................................................... 15

Options ....................................................................................... 16

Operating Controls ..................................................................... 17

Normal Sounds .......................................................................... 17

LAUNDRY TIPS ............................................................................ 18

WASHER CARE ............................................................................ 18

Cleaning Your Washer ............................................................... 18

Water Inlet Hoses ....................................................................... 19

Vacation, Storage and Moving Care .......................................... 19

TROUBLESHOOTING .................................................................. 20

ASSISTANCE OR SERVICE ......................................................... 24

WARRANTY .................................................................................. 25

INDICE

SEGURIDAD DE LA LAVADORA ................................................. 26

REQUISITOS DE INSTALACION ................................................. 27

Piezas y herramientas ................................................................ 27

Requisitos de ubicaci6n ............................................................. 28

Sistema de desagQe .................................................................. 28

Requisitos electricos .................................................................. 29

INSTRUCCIONES DE INSTALACION ......................................... 30

Antes de comenzar .................................................................... 30

Quite la base y el anillo de embalaje ......................................... 30

Conecte la manguera de desag0e ............................................. 30

Conexi6n de las mangueras de entrada .................................... 31

Fijaci6n de la manguera de desagQe ......................................... 32

Nivelaci6n de la lavadora ........................................................... 32

Complete la instalaci6n .............................................................. 33

BENEFICIOS Y CARACTERiSTICAS .......................................... 34

USO DE LA LAVADORA ............................................................... 35

Puesta en marcha de la lavadora .............................................. 35

Uso del detergente adecuado ................................................... 35

Pausa o reanudaci6n de la marcha de la lavadora ................... 36

C6mo detener la lavadora .......................................................... 37

Cambio de ciclos, modificadores y opciones ........................... 37

Luces de estado ......................................................................... 37

Ciclos .......................................................................................... 37

Modificadores ............................................................................. 39

Opciones .................................................................................... 40

Controles de funcionamiento ..................................................... 41

Sonidos normales ....................................................................... 41

CONSEJOS DE LAVANDERiA ..................................................... 42

CUIDADO DE LA LAVADORA ..................................................... 42

C6mo limpiar su lavadora .......................................................... 42

Mangueras de entrada de agua ................................................. 43

Cuidado durante las vacaciones, el almacenamiento

y las mudanzas ........................................................................... 43

SOLUCION DE PROBLEMAS ...................................................... 44

AYUDA O SERVICIO TECNICO ................................................... 48

GARANTiA .................................................................................... 49

TABLEDESMATIERES

SI_CURITI_ DE LA LAVEUSE ........................................................ 50

EXIGENCES D'INSTALLATION ................................................... 51

Outillage et pieces ...................................................................... 51

Exigences d'emplacement ......................................................... 52

Systeme de vidange ................................................................... 52

Specifications electriques .......................................................... 53

INSTRUCTIONS D'INSTALLATION ............................................. 54

Avant de commencer ................................................................. 54

Retrait de la base d'expedition et de I'anneau d'emballage .....54

Raccordement du tuyau de vidange .......................................... 54

Raccordement des tuyaux d'alimentation ................................. 55

Immobilisation du tuyau de vidange .......................................... 56

Reglage de I'aplomb de la laveuse ............................................ 56

Achever I'installation .................................................................. 57

AVANTAGES ET CARACTI_RISTIQUES ..................................... 58

UTILISATION DE LA LAVEUSE ................................................... 59

Mise en marche de la laveuse .................................................... 59

Utilisation du detergent approprie ............................................. 59

Pause ou remise en marche de la laveuse ................................ 60

Arr_t de la laveuse ...................................................................... 61

Changement des programmes, modificateurs et options .........61

Temoins lumineux ...................................................................... 61

Programmes ............................................................................... 61

Modificateurs .............................................................................. 63

Options ....................................................................................... 64

Fonctionnement des commandes ............................................. 65

Sons normaux ............................................................................ 65

CONSEILS DE LESSIVAGE .......................................................... 66

ENTRETIEN DE LA LAVEUSE ..................................................... 67

Nettoyage de la laveuse ............................................................. 67

Tuyaux d'arrivee d'eau ............................................................... 67

Precautions a prendre avant les vacances, un entreposage

ou un demenagement ................................................................ 67

DI_PANNAGE ................................................................................. 68

ASSISTANCE OU SERVICE ......................................................... 74

GARANTI E .................................................................................... 75

TODO LO QUE I_AG_NA

WASHERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer follow basic precautions,

including the following:

m Read all instructions before using the washer. mDo not wash articles that have been previously cleaned

in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, other flammable, or explosive

substances as they give off vapors that could ignite or

explode.

mDo not add gasoline, dry-cleaning solvents, or other

flammable, or explosive substances to the wash water.

These substances give off vapors that could ignite or explode.

mUnder certain conditions, hydrogen gas may be

produced in a hot water system that has not been used

for 2 weeks or more. HYDROGEN GAS IS

EXPLOSIVE. If the hot water system has not been used for such a period, before using the washing

machine, turn on all hot water faucets and let the water

flow from each for several minutes. This will release

any accumulated hydrogen gas. As the gas is

flammable, do not smoke or use an open flame during this time.

SAVE THESE INSTRUCTIONS

Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is used

near children.

Before the washer is removed from service or discarded,

remove the door or lid.

Do not reach into the washer if the drum, tub or agitator is

moving.

Do not install or store the washer where it will be exposed to the weather.

Do not tamper with controls. Do not repair or replace any part of the washer or attempt any

servicing unless specifically recommended in this manual or in

published user-repair instructions that you understand and have the skills to carry out.

See "Electrical Requirements" for grounding instructions.

INSTALLATIONREQUIREMENTS

Gather the required tools and parts before starting installation. The parts supplied are in the washer basket.

Tools needed for connecting the drain hose and water inlet hoses:

• Pliers that open to 19/16" • Flashlight (optional) (3.95 cm)

NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record hose installation or replacement dates for

future reference.

Parts supplied:

B C

Alternate Parts

Your installation may require additional parts. If you are interested in purchasing one of the items listed here, call the toll-free

number on the cover or in the "Assistance or Service" section.

If You Have: You Will Need to Buy: Laundry tub or Sump pump system (if not already

standpipe taller available) than 96" (2.4 m)

1" (2.5 cm) 2" (5 cm) diameter to 1" (2.5 cm) diameter standpipe diameter standpipe adapter,

Part Number 3363920 and connector kit Part Number 285835

Overhead sewer Standard 20 gal. (76 L) 39" (99 cm) tall

drain tub or utility sink, sump pump and connectors (available from local plumbing suppliers)

Floor drain Siphon break, Part Number 285834;

additional drain hose, Part Number 8318155 and connector kit, Part Number 285835

Water faucets 2 longer water fill hoses: beyond reach of fill 6 ft (1.8 m) Part Number 76314, hoses 10 ft (3.0 m) Part Number 350008

Lint clogged drain Drain protector, Part Number 367031

A. Drain hose form B. Water inlet hoses (2)

C. Flat water inlet hose washers (4) D. Beaded tie strap

Tools needed for securing the drain hose and leveling the washer:

• Adjustable or open end • Wood block wrench %6" (14 mm) • Ruler or measuring tape

• Level

Selectingtheproperlocationforyourwasherimproves performanceandminimizesnoiseandpossiblewasher"walk."

Yourwashercanbeinstalledinabasement,laundryroom, closet,orrecessedarea.See"DrainSystem."

IMPORTANT:Donotinstallorstorethewasherwhereitwillbe exposedtotheweather.

Properinstallationisyourresponsibility.

You will need:

• A water heater set to deliver 120°F (49°C) water to the washer.

• A grounded electrical outlet located within 4 ft (1.2 m) of where the power cord is attached to the back of the washer. See "Electrical Requirements."

• Hot and cold water faucets located within 3 ft (90 cm) of the hot and cold water fill valves, and water pressure of 20-100 psi (138-690 kPa) for best performance.

• A level floor with a maximum slope of 1" (2.5 cm) under entire washer. Installing the washer on carpeting is not

recommended.

• A sturdy floor to support the washer weight (washer, water and load) of 315 Ibs (143 kgs).

Do not store or operate your washer in temperatures at or below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures. See "Washer Care" for winterizing

information.

Installation spacing for recessed area and closet installations

The following spacing dimensions are recommended for this washer. This washer has been tested for installation with spacing of 0" (0 cm) clearance on the sides. Recommended spacing should be considered for the following reasons:

• Additional spacing should be considered for ease of installation and servicing.

• Additional spacing should be considered on all sides of the washer to reduce noise transfer.

• For closet installation with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.

• Companion appliance spacing should also be considered.

olo

_14'" may

(310or#_)_"

__ 3"*

(7.6 cm}

The washer can be installed using the standpipe drain system (floor or wall), the laundry tub drain system, or the floor drain system. Select the drain hose installation method you need. See

"Tools and Parts."

Standpipe drain system--wall or floor (views A & B)

The standpipe drain requires a minimum diameter standpipe of 2" (5 cm). The minimum carry-away capacity can be no less than 17 gal. (64 L) per minute. A 2" (5 cm) diameter to 1" (2.5 cm) diameter standpipe adapter kit is available. See "Tools and

Parts." The top of the standpipe must be at least 39" (99 cm) high and no

higher than 96" (244 cm) from the bottom of the washer.

39 _

(gecm)

Laundry tub drain system (view C)

The laundry tub needs a minimum 20 gal. (76 L) capacity. The top of the laundry tub must be at least 39" (99 cm) above the floor and no higher than 96" (244 cm) from the bottom of the washer.

Floor drain system (view D)

The floor drain system requires a siphon break that may be purchased separately. See "Tools and Parts."

The siphon break must be a minimum of 28" (71 cm) from the bottom of the washer. Additional hoses might be needed.

(2.5 cm) (69.9 cm) (2.5 cm}(2.5 cm} (68.6 cm) (12.7 cm}

A B

A. Front view

B. Side view C. Closet door with vents

*Required spacing

,2,

24111.2 =__

166cm)

t 3 ,_,

(7.6¢m)

Emectrica_ Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong° Do not use an adapter,

Do not use an extension cord° Failure to follow these }nstructions can reeumt }n death,

fire, or electr}cal shock.

A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply is required. A time-delay fuse or circuit breaker is

recommended. It is recommended that a separate circuit serving only this appliance be provided.

This washer is equipped with a power supply cord having a 3 prong grounding plug.

To minimize possible shock hazard, the cord must be plugged into a mating, 3 prong, grounding-type outlet,

grounded in accordance with local codes and ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the customer to have the properly grounded outlet installed by a qualified electrician.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

• Do not ground to a gas pipe.

• Check with a qualified electrician if you are not sure the washer is properly grounded.

• Do not have a fuse in the neutral or ground circuit.

GROUNDING INSTRUCTmONS

For a grounded, cord-connected washer: This washer must be grounded= In the event of a malfunction or breakdown, grounding will reduce the risk of electricaI

shock by providing a path of least resistance for electric current= This washer is equipped with a cord having an

equipment-grounding conductor and a grounding plug. The piug must be plugged into an appropriate outlet that is propedy installed and grounded in accordance with alI local

codes and ordinances= WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock= Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded=

Do not modify the plug provided with the appliance - if it wiII not fit the outlet, have a proper outlet instaIled by a qualified

electrician. For a permanently connected washer:

This washer must be connected to a grounded metal, permanent wiring system, or an equipment grounding

conductor must be ran with the circuit conductors and connected to the equipment-grounding terminal or lead on

the appliance.

INSTALLATIONINSTRUCTIONS

Excessive Weight Hazard Use two or more people to move and install washer. Failure to do so can result in back or other injury.

NOTE: To avoid floor damage during installation, set the washer

onto cardboard before moving across floor. IMPORTANT:

• Be sure the foam shipping base has been removed from the bottom of the washer as directed in the Unpacking

Instructions.

• If foam shipping base has not been removed, be sure lid is secured with tape before laying washer on its back.

• Removing the foam shipping base is necessary for proper operation.

6. Remove tape from lid. Open lid and remove foam packing ring from washer tub. Keep foam packing ring in case you

need to move the washer in the future.

Proper connection of the drain hose protects your floors from damage due to water leakage. Read and follow these

instructions. The drain hose is connected to your washer and is stored inside

the washer cabinet.

1. Place cardboard supports from shipping carton on floor behind washer for support.

2. Secure the lid with tape.

3. Using 2 or more people, tip the washer onto its back and place on cardboard supports.

4. Remove foam shipping base.

Set washer upright.

Remove drain hose from washer cabinet

Pull the corrugated drain hose out of the washer by first grabbing the pull tie. Continue to pull the hose until the end emerges. Do

not force excess drain hose back into the rear of the washer.

Laundry tub drain or standpipe drain

Connecting the drain hose form to the corrugated drain hose

4. Using pliers, tighten the couplings with an additional two-thirds turn.

Tighten the couplings with an additional two-thirds turn.

-F

4.5"

(11.4 cm)

A. Drain hose reliefs

!. Feed end of drain hose into one end of form. Place end of drain

hose form into the drain hose relief.

2. Bend the hose over the top of the form and feed into the other end of the form. Attach the other end of the form into the other drain

hose relief. The hose must extend 4Y_" (! 1.4 cm) beyond the form.

To keep drain water from going back into the washer:

• Do not force excess drain hose into standpipe. Hose should be secure but loose enough to provide a gap for air.

• Do not lay excess hose on the bottom of the laundry tub.

Floor drain

Do not install the drain hose form on to the corrugated drain hose, You may need additional parts. See Floor drain under

"Tools and Parts."

1. Insert new flat washers (supplied) into each end of the inlet hoses. Firmly seat the washers in the couplings,

NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result.

Clear the water lines

• Run water through both faucets and inlet hoses, into a laundry tub, drainpipe or bucket, to get rid of particles in the water lines that might clog the inlet valve screens.

• Check the temperature of the water to make sure that the hot water hose is connected to the hot water faucet and that the

cold water hose is connected to the cold water faucet.

Connect the inlet hoses to the washer

A B

A. Coupling B. Washer

Connect the inlet hoses to the water faucets

Make sure the washer basket is empty.

2. Attach the hose labeled hot to the hot water faucet. Screw on coupling by hand until it is seated on the washer.

3. Attach the hose labeled cold to the cold water faucet. Screw on coupling by hand until it is seated on the washer.

A. Hot water inlet valve

B.Cold water inlet valve

1. Attach the hot water hose to the inlet valve labeled hot.

2. Attaching one hose coupling first makes it easier to tighten the connection with pliers.

3. Screw on coupling by hand until it is seated on the washer.

Using pliers, tighten the coupling with an additional two-thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result.

Attach the cold water hose to the inlet valve labeled cold.

Screw on coupling by hand until it is seated on the washer.

Using pliers, tighten the coupling with an additional two-thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result.

Check for leaks

• Turn on the water faucets and check for leaks. A small amount of water might enter the washer. You will drain this in

a later step. NOTE: Replace inlet hoses after 5 years of use to reduce the

risk of hose failure. Record hose installation or replacement dates for future reference.

• Ifyou connect only one water hose, you must cap off the

remaining water inlet port.

• Periodically inspect and replace hoses if bulges, kinks,

cuts, wear, or leaks are found.

Fasten the drain hose to the laundry tub leg or drain standpipe with the beaded tie strap. See view A or B.

A B C

If the washer faucets and the drain standpipe are recessed, put the formed end of the drain hose into the standpipe. Tightly wrap the tie strap around the water inlet hoses and the

drain hose. See view C.

One washer foot has been installed at a different height on your new washer. The other three feet were preset at the factory. Properly leveling your washer will minimize noise and vibration.

1. Slide the washer to its final location.

2. Push on upper front panel to be sure the washer is on its rear feet.

Drape the power cord over the console.

Remove any cardboard used to move washer.

(22;>

Beaded tie strap

3. Lower right front foot until it contacts the floor. By hand, firmly rotate foot as much as an additional 11/2turns. The other three

feet have been preset at the factory.

Check the levelness of the washer by first placing a level on the lid near the console. Next, place the level on the side of the washer in the crease between the top of the washer and

the cabinet.

Level the fronL

Level the side.

5. If the washer is not level, move the washer out slightly, tip back, prop up the front of the washer on a wood block,

Adjust the feet up or down as necessary by twisting the feet. Repeat steps 1 through 4 until washer is level.

6. Use a 9/16"or 14 mm open-end wrench to turn the Iocknut counterclockwise on the foot tightly against the washer

cabinet, IMPORTANT: If the Iocknut is not tight against the washer

cabinet, the washer may vibrate.

1. Check the electrical requirements. Be sure that you have the correct electrical supply and the recommended grounding method, See "Electrical Requirements."

2. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.

3. Check that you have all of your tools.

4. Keep the foam packing ring from the washer tub for future relocation of the washer. Dispose of/recycle all packaging

materials.

5. Check that the water faucets are on.

6. Check for leaks around faucets and inlet hoses.

Electrica_ Shock Hazard

Pmuginto a grounded 3 prong outlet. Do not remove ground prong, Do not use an adapter,

Do not use an extension cord. Failure to follow these instructions can resumt in death,

fire, or electricam shock.

Plug into a grounded 3 prong outlet.

Remove any protective film or tape remaining on the washer.

Read "Washer Use."

10.

Totest and to clean your washer, measure 1/2of the detergent manufacturer's recommended amount of High Efficiency (HE) powdered or liquid detergent for a medium-size load and pour it into the detergent dispenser. Close the lid. Press POWER. Select a normal cycle and press Start. Allow it to complete one whole cycle.

BENEFITSANDFEATURES

Your washer has several benefits and features which are summarized here. Some items may not apply to your model.

The wool wash cycle of this machine has been

i_ approved by Woolmark for the washing of

Woo[ MARK instructions on the garment label and those machine, M0608.

High-Efficiency Wash System

machine washable Woolmark products provided

,:_ that the garments are washed according to the

issued by the manufacturer of this washing

High Efficiency (HE} Detergent This washer is designed for High Efficiency (HE) detergent use only. HE detergents are made to produce the right amount of

suds and give the best performance in low water wash systems.

Your new top loading, high-efficiency washer saves you time by allowing you to do fewer, larger loads. It also conserves

resources and also lowers your water and energy bills by using the following innovations.

Auto Water Level

This washer senses the load size and composition through a series of fills and wash motion. It then adjusts the water level for

the best cleaning and rinsing performance. It eliminates the guesswork. The water level is just right for every wash load size.

NOTE: You may notice during a cycle that the wash load is not completely submerged in water. This is normal for your washer.

Care Control Temperature Management

The Care Control Temperature Management system on this washer electronically senses and maintains a uniform water

temperature by regulating incoming water temperatures. Using Care Control will help dissolve detergent.

Hydro Plate Wash System

Your new washer works differently than most washers that you are accustomed to. The most striking difference is that the

washer has an hydro plate wash system. It uses this new innovative hydro plate at the bottom of the wash basket to move

your load through a mixture of water and detergent. The load is moved from the outside toward the middle with items coming up

in the center and down on the outside edges.

Dispensers

The dispensers make your washer truly automatic. It is unnecessary for you to return to the washer during the cycle to

add detergent, bleach, or fabric softener. Laundry products are added to the load at the proper time in the

wash cycle.

Spin Speeds

This washer is preset to automatically select the spin speed based on the cycle selected. Depending on your wash load, you

can change the preset speeds. The spin speed on this washer is nearly twice as fast as that of a conventional washer. You may

notice different sounds during a spin cycle because of this higher rate of speed.

Deep Clean Cleaning Action

The Deep Clean option uses Direct Inject Cleaning Action to help ensure better soil and stain removal. Deep Clean reduces the

need for pretreatment and is safe for all washable fabrics. Water flushes through the dispenser to dissolve the detergent. The

detergent mixture is then sprayed onto the load while the washer spins at low speed. This cleaning action will last up to 5 minutes

depending on the cycle selected. The washer then stops spinning, fills with water to the appropriate level and continues

washing with the selected cycle.

Innovative Features

Your new washer includes these features that help to reduce noise, increase the ease of use and improve wash performance.

Electronic Controls Electronic controls with preset cycles are easy to use whether

you are a beginner or an "expert."

Quiet Operation

This washer is insulated with sound-dampening materials to reduce washer operation sounds and noises. On some models,

an additional tub wrap is added for extra dampening of vibration and sound.

Suspension System To reduce washer "walk" and "out of balance" conditions, your

new washer combines:

• 4 Spring damper struts to isolate vibration

• Balance ring at the top and bottom of the wash basket to minimize vibration

• Operating software designed to sense and correct off- balance loads

Clean Washer Cycle

This washer features an easy-to-use Clean Washer cycle that thoroughly cleans the inside of your washing machine using higher water volumes in combination with liquid chlorine bleach.

Stainless Steel Basket The stainless steel basket is corrosion resistant and enables higher spin speeds for more water extraction, reducing drying

time.

Force Filter Wash/Rinse System This washer filters 100% of the wash and rinse water. The water is filtered then recirculated. The force filter traps sand and dirt, flushing them down the drain, so they are not redeposited onto

the clean clothes.

Delay Wash

Delay Wash allows you to load your washer and pause the start of the cycle for up to 10 hours.

End of Cycle Signal

The End of Cycle Signal produces an audible sound when the wash cycle is finished. This signal is helpful when you are

removing items from the washer as soon as it stops.

WASHERUSE

NOTE: Your washer model may vary from the model shown.

&SPIN SOAK TEM_ SOAK SIGNAL

W_S_ CYCLES MOI_EFEERS O_TEOf_S

Place a load of sorted clothes into the washer. See "Laundry Tips."

• Load evenly to maintain washer balance. Mix large and

small items. Items should move easily through the wash water.

• Load only to the top of the basket as shown. Overloading

can cause poor cleaning. Items need to move easily through the wash water.

Fire Hazard

Never place items in the washer that are dampened with gasoline or other flammabme fluids°

No washer can compmetely remove oil Do not dry anything that has ever had any type of oH on

it (including cooking oils). Doing so can reeumt in death, explosion, or fire.

WARNING: To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before

operating this appliance. The following is a guide to starting your washer. Periodic

references to other sections of this manual provide more detailed information.

Use only High Efficiency detergents. The package for this type of detergent will be marked "HE" or "High Efficiency." This wash

system, along with less water, will create too much sudsing with a regular non-HE detergent. Using regular detergent will likely result in washer errors, longer cycle times and reduced rinsing performance. It may also result in component failures and

noticeable mold or mildew. HE detergents are made to produce the right amount of suds for the best performance. Follow the manufacturer's instructions to determine the amount of detergent

to use.

Pour measured powdered or liquid High Efficiency detergent into the detergent dispenser. Always use the detergent dispenser, and do not put detergent directly onto clothes in

the washer.

Add color-safe bleach (powdered or liquid) to this dispenser, if needed. Be sure to match powdered color-safe bleach with powdered detergent or match liquid color-safe bleach with liquid detergent.

Pour measured liquid chlorine bleach into the liquid chlorine bleach dispenser, if needed. Bleach is diluted and automatically dispensed at the proper time during the wash cycle.

• Do not overfill. Do not dilute. Do not use more than 1 cup (250 mL) for a full load. Use less with a smaller load size.

• Follow the garment and the chlorine bleach manufacturer's directions for proper use.

• To avoid spilling, use a cup with a pouring spout. Do not let bleach splash, drip, or run down into the washer basket.

• At the end of the cycle, a small amount of water may be left in the dispenser. This is normal.

NOTE: Use only liquid chlorine bleach in this dispenser.

Pour measured liquid fabric softener into the fabric softener dispenser, if desired.

Add a Garment You can place additional clothing in the wash when the "Add a

Garment" status light is glowing without sacrificing wash performance.

To add a garment or pause the washer at any time

1. Press PAUSE/CANCEL once.

2. Wait until the Lid Lock light turns off, then open the lid.

3. Add items.

To restart the washer

1. Close the lid and press START.

2. To unlock the lid after the Add a Garment period, press PAUSE/CANCEL once. Pressing PAUSE/CANCEL twice will cancel the wash cycle.

You can stop the wash cycle and drain the tub by pressing the Pause/Cancel button twice or the Power button once.

You can change Cycles, Modifiers and Options anytime before Start is pressed. Not all Modifiers and Options are available for all cycles.

• A short tone sounds when a change is selected.

• Three short tones sound if an unavailable combination is selected. The last selection will not be accepted.

• Do not overfill. The dispenser holds 3 oz (94 mL), or a capful of fabric softener.

• The fabric softener is dispensed in the final rinse. If Extra Rinse is selected, the fabric softener will be dispensed during the Extra Rinse.

• Do not spill or drip any fabric softener onto the clothes.

• At the end of the cycle, a small amount of water may be left in the dispenser. This is normal.

NOTE: Use only liquid fabric softener in this dispenser.

6. Close the washer lid.

7. Press POWER. This turns on the washer display.

8. Select a Wash Cycle. See "Cycles."

9. Select the desired Modifiers. See "Modifiers."

10. Select an Option, if desired. See "Options."

11. Select Delay Wash, if desired. See "Delay Wash" in the "Modifiers" section.

12. Press START.The wash cycle begins, and the display shows the estimated remaining time. The lid will lock.

NOTE: If you do not press Start within 5 minutes of pressing Power, the washer automatically shuts off.

Changing Cycles after pressing Start

1. Press PAUSE/CANCEL twice to cancel the cycle. The washer will drain.

2. Press POWER.

3. Select the desired wash cycle.

4. Select the desired Modifiers and Options.

5. Press START.

The washer restarts at the beginning of the new cycle. NOTE: If you do not press Start within 5 minutes of pausing the

washer, the washer automatically shuts off.

Changing Modifiers and Options after pressing Start

You can change a Modifier or Option anytime before the selected Modifier or Option begins by choosing the desired Modifiers and/ or Options.

NOTE: An error tone will sound if your selection is unavailable.

To manually drain the washer and spin the load

1. Press PAUSE/CANCEL twice to cancel the wash cycle and drain the washer.

2. Press POWER.

3. Turn knob to select DRAIN & SPIN.

4. Press START.

When the spin is complete, the lid unlocks. Items can be removed from the washer.

These lights show which portion of the cycle the washer is operating. They also indicate when you can add other garments

to the wash load.

Delay Soak WashRinse Spin Done

Preset Cycle Settings

Cycle Preset Soil Wash/Rinse

Minutes* Level** Temp

Whitest Whites 85 Heavy Hot/Cold

Heavy Duty 73 Heavy Hot/Cold

Bulky Items 53 Normal Warm/Cold

Load is Done

The Done light stays on until the lid is opened or the Power or Pause/Cancel button is pressed.

Indicator lights

An indicator light shows which Cycle, Modifiers and Options you have selected.

Estimated Time Remaining

When a wash cycle is started, the estimated time remaining for the cycle, including fills and drains, will be displayed. The time will count down to the end of the cycle.

Turn the knob to choose the right wash cycle for the type of fabrics you are washing. When the knob points to a cycle, the indicator light for the cycle will glow and the indicator light for Start will blink. If the default settings for the Modifiers and Options are acceptable, you may press Start to begin the wash cycle.

Sheets/Towels 50 Normal Warm/Cold

Normal 50 Normal Warm/Cold

Casual/Perm Press 46 Medium Warm/Cold

Colors/Darks 49 Normal Cold/Cold

Quick Wash 41 Light Warm/Warm

Wool 36 Light Warm/Cold

Delicate/Handwash 37 Light Cold/Cold Soak 41 Medium Warm/Cold

Rinse & Spin 24 Not Cold/Cold

applicable

Drain & Spin 14 Not Not

applicable applicable

Clean Washer 60 Not Not

applicable applicable

*These times are for reference only and may not match your

model exactly.

**Cycle time in minutes will appear in the display while you are

making selections. The total cycle time will appear, including an estimated time for drain and fill times, once Start is pressed.

NOTE: Load only to the top of the basket. Overloading can cause poor cleaning. See "Starting Your Washer."

&SPUN SOAK ;

Preset Cycle Settings

For ease of use, preset cycle settings provide the recommended fabric care settings for each cycle.

To use the preset cycle settings:

1. Press POWER.

2. Select the cycle you want by turning the knob. The preset cycle settings will be displayed (see following chart).

NOTE: The preset times may vary slightly depending on your model.

3. Press START. The wash cycle will begin.

Whitest Whites

This cycle introduces liquid chlorine bleach to the load at the proper time for improved whitening of your heavily soiled white fabrics. Cycle combines high-speed wash action and high-speed spin speed. For maximum soil and stain removal, liquid chlorine

bleach must be used.

Heavy Duty

Use this cycle for heavily soiled or sturdy items. Cycle combines high-speed wash action and high-speed spin. Deep Clean is the default option for this cycle, but it can be turned off. See "Changing Cycles, Modifiers and Options."

Bulky Items

Use this cycle to wash large items such as comforters, sleeping bags and blankets. This cycle starts with a soak to thoroughly saturate your large load. This is followed by medium wash action and medium spin speeds to maintain load balance.

Sheets/Towels

Use this cycle for sheets, pillowcases and towels. The wash action of this cycle is designed to keep large items from tangling and bailing up.

IMPORTANT: For best performance, drop items in loose heaps evenly around the basket wall. Do not load items directly on the impeller for this cycle.

Normal

Use this cycle for normally soiled cottons and mixed fabric loads. Cycle combines high-speed wash action and high-speed spin.

Casual/Perm Press

Use this cycle to wash loads of no-iron fabrics such as sport shirts, blouses, casual business clothes, permanent press and blends. This cycle uses medium-speed wash action, a low-speed spin and a cool down process to reduce wrinkling.

Colors/Darks

Use this cycle for lightly soiled, dark or highly dyed natural fabrics such as cotton that may be susceptible to dye loss. Cycle uses low to medium-speed wash action and high-speed spin. For best

results use cold or warm water.

Quick Wash

Use this cycle to wash small, lightly soiled loads that are needed in a hurry. This short cycle combines high-speed wash action and high-speed spin for the best cleaning and shortened dry times.

Wool

This cycle combines low-speed wash and low-

speed spin action to clean items labeled as "Machine Washable Wool" on the garment care

WOO[ MAILK

Delicate/Handwash

Use this cycle to wash lightly soiled garments indicating "Machine Washable Silks" or "Gentle" cycle on the care label. This cycle uses intermittent low speed wash action and low- speed spin for optimal fabric care.

When washing waterproof items, such as plastic-lined mattress pads, shower curtains, tarpaulin (tarps) or waterproof or water- resistant sleeping bags, use the Delicate or Handwash cycle with the lowest spin speed setting available for the washer model that you have.

Garments are labeled "Hand Wash" because:

• The fiber construction may be sensitive to wash action.

• The fabric contains sensitive dyes that may bleed.

Soak

This cycle is preset for a 41-minute cycle and soak time can be adjusted according to your needs by selecting Soil Level. After the selected soak period has ended, the washer will drain but does not spin the load.

NOTE: Automatic bleach dispensing is not part of the soak cycle.

Rinse & Spin

Use this option to get a deep rinse followed by a high-speed spin. The time display will include an estimate of how long it will

take to fill and drain the washer. When to use Rinse & Spin:

• For loads that need rinsing only.

• For completing a cycle after the power has been off.

To use or change Rinse & Spin setting:

1. Turn knob to RINSE & SPIN until the Rinse & Spin indicator light glows.

2. Press START.

Drain & Spin

An extra drain and spin may help shorten drying times for some heavy fabrics or special-care items. Drain & Spin may also be used for draining the washer after canceling a cycle or completing a cycle after a power failure.

label. Pre Soak and Deep Clean options are not available in this cycle.

To use or change Drain & Spin setting:

1. Turn knob to DRAIN & SPIN until the Drain & Spin indicator

light glows.

2. Press START.

Clean Washer

Use the Clean Washer cycle once a month to keep the inside of your washer fresh and clean. This cycle uses a higher water level in combination with liquid chlorine bleach to thoroughly clean the inside of your washing machine. See "Cleaning Your Washer."

IMPORTANT: Do not add detergent to this cleaning cycle. Use only liquid chlorine bleach. Do not place garments or other items in the washer during the Clean Washer cycle. Use this cycle with an empty wash tub.

Modifiers allow you to further customize your cycles and save energy.

Soil Level

Soil level (wash time) is preset for each wash cycle. See "Preset Cycle Settings" in "Cycles." As you press the Soil Level pad, the cycle time (minutes) will increase or decrease in the Estimated Time Remaining display and a different wash time will appear. To get the minimum wash time, press the pad until the indicator light next to Light illuminates. This is the shortest wash time available for that cycle.

Normal

Medium

I eavy

Light

SOILLEVEL

• For most loads, use the time recommended in the preset cycle settings,

• For heavy soil and sturdy fabrics, press Soil Level to select more wash time, if needed.

• For light soil and delicate fabrics, press Soil Level to select less wash time, if needed.

Spin Speed

This washer automatically selects the spin speed based on the cycle selected. The preset speeds can be changed. Spin speeds

may vary by cycle.

Medium Low

I igh

N0Spin

SPINSPEED

Wash-Rinse Temp

Select a water temperature based on the type of load you are washing. Use the warmest wash water safe for fabrics. Follow garment label instructions.

Warm rinses leave the loads drier and more comfortable to handle than cold rinses. However, warm rinses also increase

wrinkling. Cold rinses may help with wrinkling and save energy.

Hot/Cold

Warm/Warm

Warm/ C01d CoWI CoW

TapCoW/CoW

Delay Wash

You can use the Delay Wash feature to delay the start of a wash cycle for up to 10 hours (depending on your model).

1. Load the washer and fill the dispensers.

2. Close the washer lid.

3. Press POWER.

4. Select the desired Cycle, Modifiers and Options.

5. Press DELAY WASH. 1H (one hour) will be displayed in the time display window. The indicator light for Delay Wash will glow.

DELAY WASH

WASH-RINSE

TEMP

Temperature Guide

Wash Water Temperature Suggested Fabrics Hot Whites and pastels

Warm Bright colors Cold Colors that bleed or fade

NOTE: In wash water temperatures colder than 60°F (15.6°C), detergents do not dissolve well. Soils may be difficult to remove.

Care Control Temperature Management

Care Control Temperature Management electronically senses and maintains a uniform wash and rinse water temperature. Care Control regulates incoming hot and cold water and is automatically turned on when a cycle is selected. (See "Preset Cycle Settings" in "Cycles.")

Care Control is available with Warm/Warm, Warm/Cold and Cold/ Cold settings. The water temperature in the Hot/Cold and Tap Cold/Cold settings depends on the water temperature at the

water inlet faucets.

• Care Control ensures consistent cleaning. The Hot and Warm setting on this washer will be cooler than

you are accustomed to. Wash temperatures in this ENERGY STAR®qualified washer are lower than temperatures you may

be used to in conventional washers. Heated water consumes the largest amount of energy that a washer uses.

• Today's detergents work well at temperatures above 60°F (15.6°C).

For a longer delay time, press DELAY WASH. The Start time will increase by 1-hour steps.

Press START.The countdown in hours to the wash cycle will show in the time display window and the indicator light will begin to flash.

NOTE: The Start indicator light will not flash when Delay Wash is chosen. You must press Start to initiate a countdown

for the cycle to begin.

To change the Delay Wash time:

• Press PAUSE/CANCEL

• Press DELAY WASH to select the desired delay time.

• Press START to begin the countdown.

To cancel Delay Wash:

Press START again to begin the cycle right away or press PAUSE/CANCEL twice.

Use these pads to select the desired options for your wash cycle.

DEEPCLEAN

EXTRARINSE

®®

PRE [NDOFCYCLE

SOAK SIGNAL

Deep Clean

This option provides enhanced cleaning action for tough stains. The Heavy Duty cycle automatically includes Deep Clean. Choosing Deep Clean will add approximately 5 minutes to a cycle. Deep Clean should be started on a dry load only and cannot be selected after the tub has started filling with water.

Deep Clean may be selected as an option with other cycles. See table for details.

Cycle Deep Clean

(Adds time to the wash cycle)

Whitest Whites Option

Heavy Duty Default Bulky Items Not available

Sheets/Towels Not available Normal Option

Casual/Perm Press Option Colors/Darks Option Quick Wash Option

Wool Not available Delicate/Nandwash Option

Soak Not available Rinse & Spin Not available

Drain & Spin Not available Clean Washer Not available

Extra Rinse An extra rinse can be used to aid in the removal of detergent or

bleach residue from garments. This option provides an additional rinse with the same water temperature as the first rinse. This is the default rinse setting for the Whitest Whites cycle.

Pre Soak Use this option for set-in stains and soil that need extra time for

removal. Soaking in this washer is different than in a conventional washer. The washer sprays the load with water and detergent at extra-low spin speed followed by a brief period of wash action at the speed of the selected cycle. This action is repeated. Pre Soak cycles through a series of sprays and wash actions followed by a pause to allow the detergent to work on the soils. The Pre Soak feature is followed by the selected cycle. Using Pre Soak will extend your wash cycle.

End of Cycle Signal Volume The End of Cycle Signal produces an audible sound when the

wash cycle is finished. This signal is helpful when you are removing items from the washer as soon as it stops. Select Loud,

Soft or Off.

Power

Press POWERto turn the washer onor off.

_0WE,t

Start Press START to start your washer after a cycle has been

selected. Be sure all desired Modifiers and Options have been selected. The lid must be closed for the washer to start.

_ART

Pause/Cancel

Press PAUSE/CANCEL once to pause or stop the washer at any time. Press PAUSE/CANCEL once to unlock the lid and add a

garment. Press START to complete the cycle from where it was stopped. Press PAUSE/CANCEL twice to stop the wash cycle.

The washer will then drain and turn off.

LidLock

Lid Lock When the Lid Lock status light glows, the washer lid is locked. NOTE: You must wait until the Lid Lock Light turns off before the

lid can be opened.

Your new washer may make sounds your old one didn't. Because the sounds might be unfamiliar, you may be concerned about them. These sounds are normal.

During washing If you select the Deep Clean option, you will hear a spin/spray

noise at the start of the cycle.

During drain If water is drained quickly from your washer (depending on your

installation), you may hear air being pulled through the pump during the end of draining.

During wash and spin This washer does not have a transmission. The motor provides

direct drive for agitation and spin. You will hear sounds that are different from those of a conventional washer.

LAUNDRYTIPS

Preparing clothes for washing

Follow these recommendations to help you prolong the life of your garments.

• Use only High Efficiency detergents. The package for this type of detergent will be marked "HE" or "High Efficiency." This wash system, along with less water, will create too much sudsing with a regular non-HE detergent. Using regular detergent will likely result in washer errors, longer cycle times and reduced rinsing performance. It may also result in component failures and noticeable mold or mildew. HE detergents are made to produce the right amount of suds for the best performance. Follow the manufacturer's instructions to determine the amount of detergent to use,

• Close zippers, snaps, and hooks to avoid snagging other items. Remove pins, buckles, and other hard objects to avoid scratching the washer interior. Remove non-washable trim

and ornaments.

• Empty pockets and turn them inside-out.

• Turn down cuffs; brush away lint and dirt.

• Turn synthetic knits inside-out to avoid pilling.

• Tie strings and sashes so they will not tangle.

• Mend tears, loose hems, and seams.

• Treat spots and stains.

• Stained or wet garments should be washed promptly for best results.

• Turn wool knits inside-out before washing.

Sorting

• Separate heavily soiled items from lightly soiled ones, even if they would normally be washed together. Separate lint-givers (towels, chenille) from lint-takers (corduroy, synthetics, permanent press), When possible, turn lint-givers inside-out.

• Separate dark colors from light colors, colorfast items from noncolorfast items.

• Sort by fabric and construction (sturdy cottons, knits, delicate items).

• Separate bulky, nonabsorbent items such as comforters, pillows and poly-filled jackets. Use the Bulky Items cycle for

these items. Separate sheets, pillowcases and towels and use the

Sheets/Towels cycle for these items. For best performance, drop items in loose heaps evenly around the basket wall and do not load items directly on the impeller for this cycle.

When washing waterproof items, such as plastic-lined mattress pads, shower curtains, tarpaulin (tarps) or waterproof or water-resistant sleeping bags, use the Delicate or Handwash cycle with the lowest spin speed setting available for the washer model that you have.

Unloading

• Remove clothes from washer after the cycle is completed. Metal objects such as zippers, snaps, and buckles may rust if left in the washer basket for a long time.

WASHERCARE

Washer Maintenance Procedure

This washer has a special cycle that uses higher water volumes in combination with liquid chlorine bleach to thoroughly clean the

inside of the washing machine. NOTES:

• Read these instructions completely before beginning the cleaning process.

It is recommended that you allow the cleanout cycle to complete without interruptions. If necessary, the cleanout

cycle may be interrupted by pressing the Power button once or the Pause/Cancel button twice.

IMPORTANT: If the cleanout cycle is interrupted, run a Rinse & Spin cycle to ensure that all remaining bleach is rinsed from the washer.

Begin procedure

1. Open the washer lid and remove all items from the washer.

2. Add liquid chlorine bleach to the bleach dispenser.

• Add 1 cup (250 mL) liquid chlorine bleach to the bleach

dispenser. NOTE: Do not add any detergent to this cleaning cycle.

Use of more than 1 cup (250 mL) of bleach will cause product damage over time.

3. Close the lid.

4. Press POWER.

5. Turn cycle control knob to CLEAN WASHER cycle.

• The Estimated Time Remaining display will show approximately 60 minutes.

6= Press STAR£

The cycle will begin and water will dispense in the washer for a moment and pause, then the lid will lock and the cycle will continue.

• Once the cleaning cycle has begun, allow the cycle to complete. An estimated cycle time will appear on the display.

• If the procedure does not sufficiently improve the machine freshness, evaluate your installation and usage conditions for

other causes.

Always do the following to maintain washer freshness

• Use only High Efficiency (HE) detergent.

Cleaning the exterior Use a soft damp cloth or sponge to wipe up any spills.

Occasionally wipe the outside of your washer to keep it looking new. Use mild soap and water. Do not use abrasive products.

Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Periodically inspect and replace inlet hoses if bulges, kinks, cuts, wear or leaks are found.

When replacing your inlet hoses, mark the date of replacement on the label with a permanent marker.

Install and store your washer where it will not freeze. Because some water may stay in the hoses, freezing can damage your washer. If storing or moving your washer during freezing weather,

winterize it.

Non-use or vacation care:

Operate your washer only when you are at home. If you will be on vacation or not using your washer for an extended period of time,

you should:

• Unplug washer or disconnect power.

• Turn off the water supply to the washer. This helps avoid accidental flooding (due to a water pressure surge) while you are away.

To winterize washer:

1. Shut off both water faucets.

2. Disconnect and drain water inlet hoses.

3. Put 1 qt (1 L) of R.V.-type antifreeze in the basket.

4. Run washer on the Rinse & Spin setting for about 30 seconds to mix the antifreeze and remaining water.

5. Unplug washer or disconnect power.

To use washer again:

1. Flush water pipes and hoses. Reconnect water inlet hoses. Turn on both water faucets.

To transport the washer:

1. Shut off both water faucets.

2. Disconnect and drain water inlet hoses.

3. If the washer will be moved during freezing weather, put 1 qt (1 L) of R.V.-type antifreeze in the basket. Run washer on the Rinse & Spin setting for about 30 seconds to mix the antifreeze and remaining water.

4. Disconnect the drain from the drain system.

5. Unplug the power cord.

6. Place the inlet hoses into the basket.

7. Drape the power cord and drain hose over edge into the basket.

8. Place foam packing ring from the original shipping materials in the top of washer. If you do not have the original foam packing ring, place heavy blankets, towels, etc. into basket opening. Close the lid and put a piece of tape over the lid and down to the front of the washer. Keep the lid taped until the washer is placed into new location.

Reinstalling the washer

1. Follow the "Installation Instructions" to locate, level and connect the washer.

2. Run the washer through the Bulky Items cycle to clean the washer and remove the antifreeze, if used. Use only HE High Efficiency detergent. Use 1/2the manufacturer's

recommended amount for a medium-size load.

Emectrica_ Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can resumt in death,

fire, or emectrical shock.

Plug in washer or reconnect power.

Run the washer through the Bulky Items cycle to clean the washer and remove the antifreeze, if used. Use only HE High Efficiency detergent. Use 1/2the manufacturer's

recommended amount for a medium-size load.

TROUBLESHOOTING

First try the solutions suggested here and possibly avoid the cost of a service call...

Washer displaying code messages

• LF "LF" (Washer is taking too long to fill) Check the following:

Are the water inlet hoses kinked or clogged? Are the water inlet valve screens clear?

Press PAUSE/CANCEL to clear display.

• Ld "Ld" (Washer is taking too long to drain water from the wash tub}

Check the following: Is the drain hose kinked or clogged? Is the drain hose installed properly? See "Connect the Drain Hose." Press PAUSE/CANCEL to clear display.

• u_ "uL" (Unbalanced Load) If the load is unbalanced, the washer will display this code while running an imbalanced load correction routine at the end of the wash cycle and before the final spin. If the code remains and the wash cycle dial is flashing after the recovery routine has stopped, open lid and redistribute the load. Close lid and press START.

• _L "oL" (Over Load) Is the washer overloaded? The washer has attempted to fill

and begin the wash cycle. Ifthe washer is overloaded, it will drain any water and detergent that was added during the fill. To correct the overload, remove several items and add detergent. Close lid and press START.

• _d "Sd" (Suds Detected)

Did you use regular detergent?

Regular or hand-washing detergents are not recommended for this washer. Use only High Efficiency ("HE") detergent.

Did you add too much detergent? Always measure detergent. Follow detergent manufacturer's

directions. If excessive suds are detected, the washer will display this

code while running a suds reduction correction routine at the end of the wash cycle. The suds reduction routine removes extra suds and assures proper rinsing of your garments. If the code remains and the wash cycle dial is flashing after the recovery routine has stopped, re-select your desired cycle using cold water. Press START. Do not add detergent.

_d "lid" (Lid Opened) Is the lid open? Close the lid to clear the display. If the lid remains open for more than 10 minutes, water in the wash

tub will drain.

H_ "HC" (Cold and Hot hoses switched)

This code will appear at the end of the wash cycle to indicate that the cold and hot water inlet hoses are switched. See

"Connect the Inlet Hoses."

• dL "dL" (Door/Lid cannot lock) Indicates lid is not locked. Check for items caught in the lid

keeping it from closing. Press PAUSE/CANCEL once to clear the code.

• dU "dU" (Door/Lid cannot unlock) Is there excessive weight on the lid, such as a basket of

laundry? Excessive weight will keep the lid from unlocking. Press PAUSE/CANCEL once to clear the code.

• F__ "F##" code Press PAUSE/CANCEL once to clear code. Press START. If

code appears again, call for service.

Noisy, vibrating, off-balance

Is the washer level? Does the washer rock when pushed against the corners?

The washer must be level. The front and rear feet must be in firm contact with the floor. Check that the Iocknuts are

tightened. See "Level the Washer." Is the floor flexing, sagging or not level?

Flooring that flexes or is uneven can contribute to noise and vibration of the washer. A 3A" (1.9 cm) piece of plywood under

the washer will reduce the sounds. See "Location Requirements."

Is the load balanced? Evenly distribute the load in the washer basket and make

sure the height of the load does not exceed the top row of basket holes. See "Starting Your Washer."

Do you hear clicking or other noises when the cycle changes from washing to draining or spinning?

When the drive system shifts or the washer basket settles between cycles you may hear noises that are different from your previous washer. These are normal washer noises.

Is the washer gurgling or humming? When the washer drains, the pump will make a continuous humming with periodic gurgling or surging sounds as the final

amounts of water are removed. This is normal.

• Are you washing a small load? You will hear more splashing sounds when washing small

loads. This is normal.

• The washer basket moves while washing. This is normal.

• Can you hear water spraying? This is part of the wash action.

• Are you washing items with metal snaps, buckles or

zippers?

You may hear metal items touching the basket. This is normal. Did you select the Bulky Items cycle?

Use the Bulky Items cycle only for oversized, nonabsorbent items such as comforters, pillows or poly-filled jackets. Other items will create an unbalanced load in this cycle.

Washer leaks

• Are the fill hoses tight?

• Are the fill hose washers properly seated? Check both ends of each hose, See "Connect the Inlet

Hoses."

Did you pull the drain hose from the washer cabinet and install it in a standpipe or laundry tub?

The drain hose should be pulled from the washer cabinet and secured to the drainpipe or laundry tub. See "Connect Drain

Hose" and "Secure the Drain Hose." Is the sink or drain clogged?

Sink and drainpipe must be able to carry away 17 gal, (64 L) of water per minute, If sink or drainpipe is clogged or slow, water can back up out of drainpipe or sink.

Is water splashing off the tub ring or the load? The wash load should be balanced and not overloaded. If the

wash load is unbalanced or overloaded, incoming water can deflect off the load.

• Is the washer properly installed? The washer must be level, The feet should be properly installed and the nuts tightened, See "Level the Washer."

Was the cycle interrupted and then the Deep Clean option

selected?

The Deep Clean option should be started on a dry load only. The Deep Clean option should not be selected after the tub has started filling with water.

Did you select Deep Clean option and use a hand-

washing detergent?

Regular or hand-washing detergents are not recommended for this washer. Use only High Efficiency ("HE") detergent.

• Check household plumbing (laundry tubs, faucets,

drainpipe, water pipes) for leaks.

Dispenser operation

Are the laundry products in the correct dispensers?

Add the correct amounts of detergent (powdered or liquid), liquid chlorine bleach, or fabric softener to the correct dispenser. You can add powdered or liquid color-safe bleach to the detergent dispenser. Be sure to match powdered color-safe bleach with powdered detergent or match liquid color-safe bleach with liquid detergent. Use only liquid chlorine bleach in the bleach dispenser.

Is there water remaining in the bottom of a dispenser? Did the dispenser drain properly?

A small amount of water may be left in a dispenser at the end of the cycle. This is normal.

E_ectrical Shock Hazard

P_ug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrica_ shock.

Washer won't fill, rinse or agitate; washer stops

• Is the power cord plugged into a grounded 3 prong

outlet?

Plug power cord into a grounded 3 prong outlet.

• Are you using an extension cord? Do not use an extension cord.

• Is there power at the plug? Check electrical source or call electrician.

• Is the indicator on the Cycle control knob properly lined

up with a cycle?

Turn the Cycle control knob to the right slightly. Are the water inlet valve screens clogged?

Turn off the water and remove inlet hoses from the washer. Remove any accumulated film or particles. Reinstall hoses,

turn on water and check for leaks.

• Are the hot and cold water faucets turned on? Turn on the water.

• Is the water inlet hose kinked? Straighten the hoses.

Does the water level seem too low, or does the washer appear to not fill completely?

The Auto Water Level feature senses the size of the load and adds the correct amount of water for the load size. You may

notice during a cycle that the wash load is not completely submerged in water. This is normal and necessary for clothes

to move.

Has a household fuse blown, or has a circuit breaker tripped?

Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician.

• Is the washer in a normal pause in the cycle? The washer may pause during certain cycles. Allow the cycle

to continue.

• Is thewasher overloaded? Wash smaller loads. See "Starting Your Washer" for

maximum load size.

Is there oversudsing? Cancel the current cycle. Select DRAIN & SPIN to drain the load. Re-select your desired cycle and press START. Do not add detergent. Use cold water.

Is the lid open? The lid must be closed during operation. The washer will not operate with the lid open.

Did you add more items to the load once the washer started?

Once the load is wet, there may appear to be space for more items. Do not add more than 1 or 2 garments after the cycle has started. For best results determine load size with dry items only.

Washer continues to fill or drain, or the cycle seems

stuck

Is the top of drain hose lower than the control knobs on

washer?

The top of the drain hose must be at least 39" (99 cm) above the floor. See "Drain System."

Does the drain hose fit too tightly in the standpipe, or is it taped to the standpipe?

The drain hose should be loose yet fit securely. Do not seal the drain hose with tape. The hose needs an air gap. See

"Installation Instructions."

Does the wash water temperature feel lower than usual? As washing progresses, the wash temperature will decrease slightly for hot and warm washes. This is normal.

To reduce wrinkling, the warm rinse is regulated to be cooler than the warm wash.

Excessive sudsing

• Did you use a non-HE detergent? Regular or hand-washing detergents are not recommended for this washer. Use only High Efficiency ("HE") detergent.

Is there excessive sudsing? Always measure detergent. Follow detergent manufacturer's directions. Ifyou have very soft water, you might need to use less detergent.

Was the cycle interrupted and then the Deep Clean option

selected?

The Deep Clean option should be started on a dry load only. The Deep Clean option should not be selected after the tub has started filling with water.

Washer won't drain or spin; water remains in washer

• Is the drain hose clogged, or the end of the drain hose

more than 96" (244 cm) above the floor?

See "Drain System." Is the lid open?

The lid must be closed during operation. The washer will not operate with the lid open.

Is there excessive sudsing? Always measure detergent. Follow detergent manufacturer's directions. If you have very soft water, you may need to use

less detergent. Use only High Efficiency ("HE") detergent.

Wash/Rinse temperature

Are the hot and cold water inlet hoses reversed?

If the hot and cold water inlet hoses are reversed, the washer will display an "HC" error code at the end of the cycle. See

"Connect the Inlet Hoses." Are you washing many loads?

As your frequency of loads washed increases, the water temperature may decrease for hot and warm temperatures.

This is normal.

• Do you have an ENERGY STAR _qualified washer? The wash water temperatures may feel cooler to you than those of your previous washer. This is normal.

Cycle did not run Deep Clean option

Did you select the Deep Clean option?

The Deep Clean option must be selected for it to be included in a wash cycle. The Deep Clean option should be started on a dry load only. Deep Clean should not be selected after the tub has started filling with water.

• The Deep Clean option is a default in the Heavy Duty cycle and may be added to other cycles.

Load too wet

• Did you use the right cycle for the load being washed? Select a higher spin speed.

• Did you use a cold rinse? Cold rinses leave loads wetter than warm rinses. This is normal.

Did you wash an extra large load? A large unbalanced load could result in a reduced spin speed and wet clothes at the end of the cycle. Evenly distribute the load and make sure the height of the load does not exceed the top row of basket holes.

Residue or lint on load

• Did you add detergent to the dispenser? For best results, use the dispenser to dissolve the detergent.

• Did you sort properly? Sort lint givers (towels, chenille) from lint takers (corduroy, synthetics). Also sort by color.

Did you overload the washer? The wash load must be balanced and not overloaded.

Clothes should move freely. Lint or powdered detergent can be trapped in the load if the washer is overloaded. Wash smaller loads. See "Starting Your Washer" for maximum load

size.

• Bid you use enough detergent? Follow detergent manufacturer's directions. Use enough detergent to hold the lint in the water.

• Did you line dry your clothing? If so, you can expect some lint on the clothing. The air movement and tumbling of a dryer removes lint from the load.

• Was paper or tissue left in pockets?

• Is your water colder than 60°F (15.6°0)? Wash water colder than 60°F (15.6°C) may not completely dissolve the detergent.

Did you use the proper Soil Level and Wash Cycle for the load?

Reducing wash time (duration) and wash speed are ways to reduce lint.

• Did you add detergent to the dispenser? For best results, use the dispenser to dissolve the detergent.

Load is wrinkled, twisted or tangled

• Did you unload the washer promptly? Unload the washer as soon as it stops.

Did you use the right cycle for the load being washed? To reduce wrinkling, tangling and twisting, select a cycle with

low wash and spin speeds, such as Delicate/Handwash or Casual/Perm Press.

Did you overload the washer? The wash load must be balanced and not overloaded. Loads

should move freely during washing to reduce wrinkling, tangling and twisting.

• Was the wash water warm enough to relax wrinkles? If safe for the load, use warm or hot wash water. Use cold

rinse water. Are the hot and cold water hoses reversed?

Check that the hot and cold water hoses are connected to the correct faucets. If the hot and cold water inlet hoses are

reversed, the washer will display an "HC" error code at the end of the cycle. See "Connect the Inlet Hoses." A hot rinse

followed by spin will cause wrinkling.

Stains, gray whites, dingy colors

• Did you properly sort the load? Dye transfer can occur when mixing whites and colors in a

load. Sort dark clothes from whites and lights.

• Was the wash temperature too low? Use hot or warm washes if safe for the load. Make sure your hot water system is adequate to provide a hot water wash.

Did you use enough detergent, or do you have hard water?

Use more detergent for washing heavy soils in cold or hard water. Water temperature should be at least 60°F (15.6°C) for soap to dissolve and work properly. For best performance, use the detergent manufacturer's recommended amounts.

Did you follow the manufacturer's directions when adding detergent and fabric softener?

Measure detergent and fabric softener. Use enough detergent to remove soil and hold it in suspension. Dilute fabric softener and add to the rinse portion of a cycle only. Do not drip fabric

softener onto clothes.

Is there above average iron (rust) in water?

You may need to install an iron filter.

Did you add detergent to the dispenser?

For best results, use the dispenser to dissolve the detergent. Did you add fabric softener directly to the load?

Use your fabric softener dispenser. Do not drip fabric softener onto clothes.

Did you use a fabric softener dispensing ball? Use the fabric softener dispenser provided with the washer. Dispensing balls will not operate correctly with this washer.

Did you unload the washer promptly? To avoid dye transfer, unload the washer as soon as it stops.

Did you add detergent, chlorine bleach or fabric softener too late in the cycle?

Detergent, chlorine bleach, and fabric softener should be added to the dispensers before starting the washer.

Did you use Quick Wash on a large load?

Quick Wash is designed to wash only a few items for best results.

Garments damaged

• Were sharp items removed from pockets before washing? Empty pockets, zip zippers, snap or hook fasteners before washing to avoid snagging and tearing of load.

Were strings and sashes tied to avoid tangling? Straps and strings can easily become entangled in the load, causing strain on seams and tearing.

Were items damaged before washing? Mend rips and broken threads in seams before washing.

Did you overload the washer? The wash load must be balanced and not overloaded. Loads

should move freely during washing.

Did you add chlorine bleach properly?

Do not pour chlorine bleach directly onto load. Wipe up bleach spills. Undiluted bleach will damage fabrics. Do not place load items on top of the bleach dispenser when loading and unloading the washer (on some models). Do not use

more than the manufacturer's recommended amount for a full load.

Did you follow the garment manufacturer's care label instructions?

+ 53 hidden pages