Whirlpool WTW4850HW1, WTW4850HW0 Owner’s Manual

Top-Loading

High Efficiency Washer

Use and Care Guide

Para una versión de estas instrucciones en español, visite www.whirlpool.com

Guide d’utilisation

et d’entretien de la laveuse

haute efficacité avec

chargement par le dessus

Table of Contents

WASHER SAFETY ....................................................................... 2

WHAT’S UNDER THE LID ........................................................... 3

CONTROL PANEL AND FEATURES .......................................... 4

CYCLE GUIDE ............................................................................. 6

USING YOUR WASHER .............................................................. 8

WASHER MAINTENANCE ........................................................ 11

TROUBLESHOOTING ............................................................... 13

WARRANTY ............................................................................... 18

ASSISTANCE OR SERVICE .................................. BACK COVER

Table des matières

SÉCURITÉ DE LA LAVEUSE .................................................... 19

CE QUI EST SOUS LE COUVERCLE ....................................... 20

TABLEAU DE COMMANDE

ET CARACTÉRISTIQUES ......................................................... 21

GUIDE DES PROGRAMMES .................................................... 23

UTILISATION DE LA LAVEUSE ................................................ 25

ENTRETIEN DE LA LAVEUSE .................................................. 28

DÉPANNAGE ............................................................................. 31

GARANTIE ................................................................................. 38

ASSISTANCE OU SERVICE. ............... COUVERTURE ARRIÈRE

W11172317A W11172322A-SP

Designed to use only HE (High Efciency) detergents. Conçue pour l’utilisation d’un détergent haute efcacité seulement.

Washer Safety

What’s Under the Lid

Lid Lock

To allow for higher spin speeds, the lid will lock and the Lid Locked light will turn on. When this light is lit, the lid is locked and cannot be opened without pausing the cycle. When this light is blinking, the washer is paused. When this light is off, the lid can be opened. After the cycle has started, the washer will ll to the appropriate water level. On select cycles, agitation will occur while the basket is lling with water. This is normal. When the washer is done lling, it will begin the wash phase. If you need to open the lid to add a garment after this point, the lid will remain unlocked during the entire agitation portion of the wash phase. The cycle will automatically pause when the lid is opened, and the cycle will resume once the lid is closed. The lid will lock before the spin phase begins. If you need to pause or stop after this point, you must press the START/PAUSE/ CANCEL button and wait for the lid to unlock. The lid will only unlock after washer movement has stopped. Depending on when in the cycle you try to pause, it may take from several seconds to several minutes for the lid to unlock. Press START/ PAUSE/CANCEL to resume the cycle.

Sensing

This washer automatically senses the load size for most cycles, and chooses an appropriate water level according to the load size detected. This washer also performs a series of spins to check for load balance. During this time, a series of clicks and a whirring noise signal that sensing technology is determining if there is an off-balance load.

Water Level Options

Set the Water Level knob to the Auto Sensing setting and the washer automatically adjusts the water level to the load size. Set the Water Level knob to the Deep Water Wash setting and the washer automatically adds more water to any cycle at any time during the wash process.

Spray Rinse

Select cycles default to a spray rinse. During these cycles, you will hear water enter the washer as the tub spins, allowing the rinse water to penetrate clothes. Check the “Cycle Guide” for details.

Choosing the Right Detergent

Use only High Efciency detergents. The package will be marked “HE” or “High Efciency.” Using non-HE detergent will likely result in longer cycle times and reduced rinsing performance. It may also result in component malfunction and, over time, buildup of mold or mildew. HE detergents should be low-sudsing and quick-dispersing to produce the right amount of suds for the best performance. They should hold soil in suspension so it is not redeposited onto clean clothes. Not all detergents labeled as High Efciency are identical in formulation and their ability to reduce suds. For example, natural, organic, or homemade HE detergents may generate a high level of suds. Always follow the detergent manufacturer’s instructions to determine the amount of detergent to use.

Use only High Efciency (HE) detergent.

Normal Sounds You Can Expect

At different stages of the wash cycle, you may hear sounds and noises that are different from those of your previous washer. For example, you may hear a clicking and hum at the beginning of the spin phase, as the lid lock goes through a self-test. There will be different kinds of humming sounds as the impeller tests for load balance or moves the load. And sometimes, you may hear nothing at all, as the washer determines the correct water level for your load or allows time for clothes to soak.

IMPORTANT:

■ The lid must be closed before the washer basket lls with water and for the wash cycle to start. If the lid is opened, the cycle

pauses and all lling/agitation motion halts. Once the lid is closed, the cycle automatically resumes. However, if the Start/Pause/ Cancel button is pressed prior to opening the lid, the lid must be closed and the Start/Pause/Cancel button pressed again to resume the cycle.

■ Rinse option must be set to Auto with Extra Rinse, Deep Water Rinse, or Deep Water with Extra Rinse if using fabric softener

during a cycle—during the nal rinse, open the lid and manually add the measured, recommended amount of fabric softener.

Control Panel and Features

452

432

Not all features and options are available on all models.

SOIL LEVEL (on some models)

Select the setting most suitable for your load. For heavily soiled and sturdy fabrics, select Heavy soil level for more wash time. For lightly soiled and delicate fabrics, select Light or Extra Light soil level for less wash time. A lighter soil level setting will help reduce tangling and wrinkling.

WASH TEMP or WASH TEMPERATURE

Wash Temp senses and maintains uniform water temperatures by regulating incoming hot and cold water.

Select a wash temperature based on the type of fabric and soils being washed. For best results, use the warmest wash water safe for your fabric, as speci ed by the garment label instructions.

■ On some models and cycles, warm and hot water may

be cooler than your previous washer.

■ Even in a cold- and cool-water wash, some warm water

may be added to the washer to maintain a minimum temperature.

All rinses are cold.

WASH CYCLE KNOB

Use the Wash Cycle knob to select cycles on your washer. See “Cycle Guide” for detailed descriptions of cycles.

Appearance may vary.

RINSE OPTION

Select the option most suitable for your load. Select Auto with Extra Rinse, Deep Water Rinse, or Deep Water with Extra Rinse if using fabric softener during a cycle—during the  nal rinse, open the lid and manually add the measured, recommended amount of fabric softener.

WATER LEVEL

Set the Water Level knob to the Auto Sensing setting and the washer will automatically sense the appropriate water level for the load size and type.

Set the Water Level knob to the Deep Water Wash setting and the washer will automatically add more water to any cycle at any time during the wash process.

NOTE: Expect longer cycle times due to extended  ll times when using the Deep Water Wash option.

START/PAUSE/CANCEL BUTTON

Press to start the selected cycle. Press again to pause the cycle and unlock the lid. Close the lid and press to restart the cycle. Press and hold to cancel a cycle and pump out the washer.

NOTE: If the washer is spinning, it may take several minutes to unlock the lid.

PROGRESS LIGHTS

The Progress Lights show the progress of a cycle. At each stage of the process, you may notice sounds or pauses that are different from traditional washers.

SENSING/FILL

When the Start/Pause/Cancel button is pressed and the Water Level knob is set to Auto Sensing, the washer will ll and begin sensing to determine load size and balance. A short but noticeable pause in the cycle action occurs during sensing. This is normal.

Once sensing is complete, the washer will ll to the

appropriate level for the detected load size and, on select cycles, agitation will occur during lling. This, too, is normal. When the washer is done lling, it will begin the wash phase of the cycle. To ensure that the most accurate load size is detected, avoid opening the lid during the “Sensing” phase.

NOTE: Sensing and wash phases will be paused by

opening the unlocked lid. Close the lid to resume the cycle. If the lid is left open for more than 10 minutes, the washer will cancel the cycle and pump out the water.

WASH

The washer will ll to the correct water level based on the load size and the Water Level selection. Certain cycles may agitate during the ll process to boost cleaning. When the wash cycle begins, you will hear the impeller increase speed. The motor sounds may change at different stages in the wash cycle while the washer performs different wash actions.

NOTE: The lid will automatically lock after the wash

phase completes and before the initial spinout occurs, and will remain locked for the rest of the cycle.

RINSE

Certain cycles use a spray rinse, which adds water to the tub while the basket spins. You may hear the motor turning on briey (short hum) to move the basket while lling. In some cases, you may also hear sounds similar to the wash cycle as the washer lls, rinses, and moves the load.

FINAL SPIN

The washer spins the load at increasing speeds for proper water removal based on the selected cycle and spin speed.

CYCLE COMPLETE

Once the cycle is complete, the lid will unlock and this light will come on. For best results, remove the load promptly.

LID LOCKED

The Lock feature allows for higher spin speeds. When lit, the lid is locked and cannot be opened without pausing the cycle. When the light is off, the lid can be opened.

To open the lid after it has been

locked, press START/PAUSE/ CANCEL. The lid will unlock once the washer movement has stopped. This may take several minutes if the load was spinning at high speed. Press START/PAUSE/CANCEL while the lid is closed to resume the cycle.

Appearance

may vary

Cycle Guide

For best fabric care, choose the cycle that best ts the load being washed. Recommended settings for best performance are shown in Bold. Not all cycles and options are available on all models.

Items to wash: Cycle: Wash Temp:* Spin

Sturdy fabrics, colorfast items, towels, jeans

Heavy Hot

Warm

Cool Cold

Tap Cold

Heavily soiled white fabrics

Whites

with Soak

Hot

Warm

‡

Cool Cold

Tap Cold

Large items such as sheets, sleeping bags, small comforters, jackets, small, washable

Bulky/Sheets Hot

Warm

Cool Cold

Tap Cold

rugs

Speed:**

Cycle Details:

High Use this cycle for heavily soiled or sturdy items. Water-level

sensing process may take longer for some items than for others because they will absorb more water than other fabric types.

Gentleness

Efciency

Cleaning

Good

†

Best

High This cycle, when used with chlorine bleach, improves

whitening of soiled white fabrics.

‡

To enhance cleaning, select Whites with Soak, which automatically adds about 10 minutes of soak time after the ll phase, and then automatically runs the Whites cycle.

Gentleness

Efciency

Cleaning

Good

†

Best

Low Use this cycle to wash large items such as jackets and small

comforters. The washer will ll with enough water to wet down the load before the wash portion of the cycle begins and uses a higher water level than other cycles.

Gentleness

Efciency

Cleaning

Good

†

Best

Cottons, linens, and mixed loads

Bright and darkly colored cottons and mixed loads

Normal Hot

Tap Cold

Colors

with Soak

Tap Cold

Warm

Cool Cold

Hot

Warm

Cool

Cold

High Use this cycle for normally soiled cottons and mixed loads.

Gentleness

Efciency

Cleaning

Good

†

Best

High Use this cycle to wash darks and colors, including mixed

loads and activewear.

To enhance cleaning, select Colors with Soak, which automatically adds about 10 minutes of soak time after the ll phase, and then automatically runs the Colors cycle.

Machine-wash silks, handwash fabrics

Delicates Hot

Warm

Cool

Cold

Tap Cold

Gentleness

Efciency

Low Use this cycle to wash lightly soiled items indicating

“Machine Washable Silks” or “Gentle” cycle on the care label. Place small items in mesh garment bags before washing. This cycle uses a higher, preset water level.

Gentleness

Efciency

Cleaning

Good

†

Good

†

Best

NOTE: If you are using fabric softener, be sure to select one of the following Rinse Option settings: Auto with Extra Rinse, Deep Water Rinse, or Deep Water with Extra Rinse. During the nal rinse, open the lid and add the measured, recommended amount of fabric softener.

**All rinses are cold.

**Spin speed is integrated into the cycle and cannot be selected or modied.

†

Efcient use of resources, such as energy and water.

Items to wash: Cycle: Wash Temp:* Spin

Small loads, cottons, polyester, permanent press

Quick Wash Hot

Warm

Cool Cold

Tap Cold

Speed:**

Cycle Details:

High Use this cycle to wash small, lightly soiled loads of two or

three items that are needed in a hurry.

Gentleness

Efciency

Cleaning

Good

†

Best

Swimsuits and items requiring rinsing without

Rinse &

Spin

Cold rinse only High Combines a rinse and high-speed spin for loads requiring

an additional rinse cycle. Use this cycle to complete a load after power interruption or for loads that require rinsing only.

detergent Hand-washed items

or dripping-wet items

Drain &

Spin

N/A High This cycle uses a spin to shorten drying times for heavy

fabrics or special-care items washed by hand. Use this cycle to drain washer after canceling a cycle or completing a cycle after a power failure.

No clothes in washer

Clean Washer

with affresh

Hot Low Use this cycle every 30 washes to keep the inside of your

washer fresh and clean. This cycle uses a higher water level. Use with affresh

Washer Cleaner tablet or liquid chlorine bleach to thoroughly clean the inside of your washer. This cycle should not be interrupted. See “Washer Care.”

IMPORTANT: Do not place garments or other items in the washer during the Clean Washer with affresh

cycle. Use

this cycle with an empty wash tub.

**All rinses are cold.

**Spin speed is integrated into the cycle and cannot be selected or modied.

†

Efcient use of resources, such as energy and water.

Using Your Washer

1. Sort and prepare your laundry

■ Empty pockets. Loose change, buttons, or any small

object can pass under the impeller and become trapped, causing unexpected sounds.

■ Sort items by recommended cycle, water temperature,

and colorfastness.

■ Separate heavily soiled items from lightly soiled.

■ Separate delicate items from sturdy fabrics.

■ Do not dry garments if stains remain after washing

because heat can set stains into fabric.

■ Treat stains promptly.

■ Close zippers, fasten hooks, tie strings and sashes,

and remove non-washable trim and ornaments.

■ Mend rips and tears to avoid further damage to items

during washing.

Helpful Tips:

■ When washing water-proof or water-resistant items,

load evenly.

■ Use mesh garment bags to help avoid tangling when

washing delicate or small items.

■ Turn knits inside out to avoid pilling. Separate lint-takers

from lint-givers. Synthetics, knits, and corduroy fabrics will pick up lint from towels, rugs, and chenille fabrics.

NOTE: Always read and follow fabric care label instructions to avoid damage to your items.

2. Add laundry products

Add a measured amount of HE detergent or single-dose laundry packet into the basket.

If using Oxi-type boosters, color-safe bleach, or fabric-softener crystals, add to the bottom of the washer basket before adding clothes.

IMPORTANT: Use only High Ef ciency detergents. The package will be marked “HE” or “High Ef ciency.” Using regular detergent will likely result in longer cycle times and reduced rinsing performance. It may also result in component failures and noticeable mold or mildew. HE detergents are made to produce the right amount of suds for the best performance.

NOTE: Follow the manufacturer’s instructions to determine the amount of laundry products to use.

3. Load laundry into washer

For best performance, load items in loose heaps evenly around the impeller. Try mixing different-sized items to reduce tangling.

IMPORTANT: Items need to move freely for best cleaning and to reduce wrinkling and tangling.

4. Add liquid chlorine bleach

to dispenser, if desired

5. Select cycle

Appearance may vary

Turn cycle knob to choose your wash cycle. For more information, see “Cycle Guide.”

6. Select soil level (on some models)

Liquid

Chlorine Bleach

Do not over ll, dilute, or use more than 1 cup (236 mL). Do not use color-safe bleach or Oxi products in the same cycle with liquid chlorine bleach.

Once you select a cycle, select the soil level by turning the Soil Level knob to the desired setting.

7. Select wash temp

or wash temperature

Once you select a cycle, select the desired wash temperature by turning the Wash Temp or Wash Temperature knob to the appropriate setting based on your load. All rinses are cold.

NOTE: Always read and follow fabric care label instructions to avoid damage to your garments.

Wash Temp Suggested Fabrics Hot

Some cold water is added to save energy. This may be cooler than your hot water heater setting.

Warm

Some cold water will be added, so this may be cooler than what your previous washer provided.

Cool

Warm water is added to assist in soil removal and to help dissolve detergents. Cool is slightly warmer than cold.

Cold

Warm water may be added to assist in soil removal and to help dissolve detergents.

Whites and pastels Durable items Heavy soils

Bright colors Moderate to light soils

Colors that bleed or fade

Light soils

Dark colors that bleed or fade

Light soils

8. Select rinse option and water level

Select the number of rinses by turning the Rinse Option knob to the desired setting.

IMPORTANT: The Rinse Option knob must be set to Auto with Extra Rinse, Deep Water Rinse, or Deep Water with Extra Rinse if using fabric softener during a cycle—during the  nal rinse, open the lid and manually add the measured, recommended amount of fabric softener.

Set the Water Level knob to the Auto Sensing setting and the washer will automatically sense the appropriate water level for the load size and type.

Set the Water Level knob to the Deep Water Wash setting and the washer will automatically add more water to any cycle at any time during the wash cycle.

NOTE: The cycle will be longer due to extended  ll times when using the Deep Water Wash setting.

Tap Cold

This is the temperature from your faucet.

Dark colors that bleed or fade

Light soils

9. Press START/PAUSE/CANCEL

to begin wash cycle

Appearance

may vary

Press START/PAUSE/CANCEL to start the wash cycle. When the cycle has  nished, the Cycle Complete progress light will light. Promptly remove garments after cycle has completed to avoid odor, reduce wrinkling, and avoid rusting of metal hooks, zippers, and snaps.

Unlocking the lid to add garments

If you need to add one or two missed garments after the wash has started, simply open the lid and this will pause the cycle. After adding the garments, simply close the lid and the cycle will resume. The washer may add some additional water to offset the added garments.

If, instead, you press Start/Pause/Cancel to pause the cycle and then open the lid to add garments, you will need to press Start/Pause/Cancel after closing the lid to resume the cycle.

NOTE: Washer will not  ll with the lid open. IMPORTANT: If lid is left open for more than 10 minutes, the

water will pump out automatically.

Manual soak

If you would like to manually soak your garments at any time during the wash portion of the cycle, press START/PAUSE/ CANCEL and leave the lid closed. Once your desired soak time has elapsed, press START/PAUSE/CANCEL again to continue the cycle. As long as the lid remains closed, your soak time can be longer than 10 minutes. However, if the lid is opened during the soak and remains open for more than 10 minutes, the water will pump out automatically.

10. Add fabric softener, if desired

During the  nal rinse, wait until the washer has completed  lling and press START/PAUSE/CANCEL to pause the washer. Lift the lid and add the measured, recommended amount of liquid fabric softener. Do not use more than the recommended amount. Close the lid and press START/PAUSE/CANCEL again to start the washer. Always follow manufacturer’s directions for correct amount of fabric softener based on your load size.

Washer Maintenance

WATER INLET HOSES

Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Periodically inspect and replace inlet hoses if bulges, kinks, cuts, wear, or leaks are found.

When replacing your inlet hoses, mark the date of replacement on the label with a permanent marker.

NOTE: This washer does not include inlet hoses. See the Installation Instructions for more information.

WASHER CARE

Recommendations to Help Keep Your Washer Clean

and Performing at its Best

1. Always use High Ef ciency (HE) detergents and follow

the detergent manufacturer’s instructions regarding the amount of detergent to use. Never use more than the recommended amount because that may increase the rate at which detergent and soil residue accumulate inside your washer, which in turn may result in undesirable odor.

2. Use warm and hot wash water settings sometimes (not

exclusively cold-water washes) because they do a better job of controlling the rate at which soils and detergent accumulate.

3. Always leave the washer lid open between uses to help

dry out the washer and prevent the buildup of odorcausing residue.

Cleaning Your Top Loading Washer

Read these instructions completely before beginning the routine cleaning processes recommended below. This washer maintenance procedure should be performed, at a minimum, once per month or every 30 wash cycles, whichever occurs sooner, to control the rate at which soils and detergent may otherwise accumulate in your washer.

Cleaning the Inside of the Washer

To keep your washer odor-free, follow the usage instructions provided above and use this recommended monthly cleaning procedure:

Clean Washer Cycle

This washer has a special cycle that uses higher water volumes in combination with affresh liquid chlorine bleach to clean the inside of the washer.

Begin procedure

1. affresh

a. Open the washer lid and remove any clothing or items. b. Place an affresh

c. Do not place an affresh

d. Do not add any detergent or other chemical to the

e. Close the washer lid. f. Select the cycle recommended for cleaning the inside

of the washer.

g. Press the START/PAUSE/CANCEL button to start

NOTE: For best results, do not interrupt cycle. If cycle

(Recommended for Best Performance):

must be interrupted, press START/PAUSE/CANCEL once. After the cycle has stopped, run a Rinse & Spin cycle to rinse cleaner from washer.

Washer Cleaner Cycle Procedure

of the washer basket.

detergent dispenser.

washer when following this procedure.

the cycle.

Washer Cleaner tablet in the bottom

Washer Cleaner or

Washer Cleaner tablet in the

WASHER CARE (cont.)

WINTER STORAGE CARE

2. Chlorine Bleach Procedure (Alternative): a. Open the washer lid and remove any clothing or items. b. Add 1 cup (236 mL) of liquid chlorine bleach to the

bleach compartment.

NOTE: Use of more liquid chlorine bleach than is recommended above could cause washer damage over time.

c. Close the washer lid. d. Do not add any detergent or other chemical

to the washer when following this procedure.

e. Select the cycle recommended for cleaning the inside

of the washer.

f. Press the START/PAUSE/CANCEL button to start

the cycle.

NOTE: For best results, do not interrupt cycle. If cycle

must be interrupted, press START/PAUSE/CANCEL once. After the cycle has stopped, run a Rinse & Spin cycle to rinse bleach from washer.

Description of Clean Washer Cycle Operation:

1. This cycle will  ll to a water level higher than in normal

wash cycles to provide rinsing at a level above the water line for normal wash cycle.

2. During this cycle, there will be some agitation and

spinning to increase the removal of soils.

After this cycle is complete, leave the lid open to allow for better ventilation and drying of the washer interior.

Cleaning the Dispensers

After a period of using your washer, you may  nd some residue buildup in the washer’s dispensers. To remove residue from the dispensers, wipe them with an affresh Machine Cleaning Wipe or a damp cloth and towel dry either before or after you run the Clean Washer cycle. Do not attempt to remove the dispensers or trim for cleaning. The dispensers and trim are not removable. If your model has a dispenser drawer, however, remove the drawer and clean it before or after you run the Clean Washer cycle. Use an allpurpose surface cleaner, if needed.

Cleaning the Outside of the Washer

Use an affresh or a sponge to wipe away any spills. Use an affresh Cleaning Wipe or only mild soaps or cleaners when cleaning external washer surfaces.

IMPORTANT: To avoid damaging the washer’s  nish, do not use abrasive products.

Machine Cleaning Wipe, a soft, damp cloth,

Machine

IMPORTANT: To avoid damage, install and store washer where it will not freeze. Some water may stay in hoses, and freezing can damage washer. If storing or moving during freezing weather, winterize your washer.

To winterize washer:

1. Shut off both water faucets; disconnect and drain water

inlet hoses.

2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run

washer on Rinse & Spin cycle for about 30 seconds to mix antifreeze and remaining water.

3. Unplug washer or disconnect power.

TRANSPORTING YOUR WASHER

1. Shut off both water faucets. Disconnect and drain water

inlet hoses.

2. If washer will be moved during freezing weather, follow

“Winter Storage Care” directions before moving.

3. Disconnect drain hose from drain system and drain any

remaining water into a pan or bucket. Disconnect drain hose from back of washer.

4. Unplug power cord.

5. Place inlet hoses and drain hose inside washer basket.

6. Drape power cord over edge and into washer basket.

7. Place packing tray from original shipping materials back

inside washer. If you do not have packing tray, place heavy blankets or towels into basket opening. Close lid and place tape over lid and down front of washer. Keep lid taped until washer is placed in new location. Transport washer in upright position.

NON-USE AND VACATION CARE

Operate your washer only when you are home. If moving, or not using your washer for a period of time, follow these steps:

1. Unplug or disconnect power to washer.

2. Turn off water supply to washer to avoid  ooding due

to water-pressure surge.

+ 28 hidden pages