Whirlpool WRT111SFAA, WRT111SFAB, WRT111SFAW Owner's Manual

REFRIGERATOR

USER INSTRUCTIONS

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING or PROBLEM SOLVER, please visit our website at www.whirlpool.com for additional information. If you still need assistance, call us at 1-800-253-1301. In Canada, visit our website at www.whirlpool.ca or call us at 1-800-807-6777.

You will need your model and serial number, located on the inside wall of the refrigerator compartment.

Table of Contents / Índice

REFRIGERATOR SAFETY.....................................................................	2
Proper Disposal of Your Old Refrigerator...........................................	2
INSTALLATION INSTRUCTIONS .........................................................	3
Unpack the Refrigerator......................................................................	3
Location Requirements.......................................................................	3
Electrical Requirements ......................................................................	4
Water Supply Requirements...............................................................	4
Connect the Water Supply..................................................................	4
Refrigerator Doors...............................................................................	5
Adjust the Doors .................................................................................	8
REFRIGERATOR USE ...........................................................................	8
Using the Controls ..............................................................................	8
Ice Maker.............................................................................................	9
REFRIGERATOR FEATURES ...............................................................	9
Refrigerator Shelves............................................................................	9
Meat Drawer......................................................................................	10
Crisper...............................................................................................	10
Utility or Egg Bin ...............................................................................	10
FREEZER FEATURES .........................................................................	11
Freezer Shelf .....................................................................................	11
DOOR FEATURES ...............................................................................	11
Door Rails or Trivets..........................................................................	11
Can Racks and Door Bins.................................................................	11
REFRIGERATOR CARE.......................................................................	12
Cleaning ............................................................................................	12
Changing the Light Bulbs .................................................................	12
Vacation and Moving Care ...............................................................	12
PROBLEM SOLVER.............................................................................	13
ACCESSORIES ....................................................................................	14
WARRANTY..........................................................................................	15

SEGURIDAD DEL REFRIGERADOR..................................................	16
INSTRUCCIONES DE INSTALACIÓN................................................	17
Desempaque el refrigerador.............................................................	17
Cómo deshacerse adecuadamente de su refrigerador viejo...........	17
Requisitos de ubicación ...................................................................	18
Requisitos eléctricos.........................................................................	18
Requisitos del suministro de agua ...................................................	19
Conexión del suministro de agua.....................................................	19
Puertas del refrigerador ....................................................................	20
Ajuste las puertas .............................................................................	23
USO DE SU REFRIGERADOR ............................................................	23
Uso de los controles.........................................................................	23
Fábrica de hielo.................................................................................	24
CARACTERÍSTICAS DEL REFRIGERADOR .....................................	25
Estantes del refrigerador ..................................................................	25
Cajón para carnes.............................................................................	25
Cajón para verduras .........................................................................	25
Compartimiento para huevos o de uso general...............................	26
CARACTERÍSTICAS DEL CONGELADOR ........................................	26
Estante del congelador.....................................................................	26
CARACTERÍSTICAS DE LA PUERTA ................................................	27
Rieles o anaqueles de la puerta .......................................................	27
Portalatas y recipientes de la puerta ................................................	27
CUIDADO DE SU REFRIGERADOR...................................................	27
Limpieza............................................................................................	27
Cómo cambiar los focos...................................................................	28
Cuidado durante las vacaciones y mudanzas .................................	28
SOLUCIÓN DE PROBLEMAS.............................................................	29
ACCESORIOS ......................................................................................	31
GARANTÍA............................................................................................	31

W10465565A

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean:

DANGER

WARNING

You can be killed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING:To reduce the risk of fire, electric shock, or injury to persons when using the refrigerator, follow basic precautions, including the following:

■ Plug into a grounded 3 prong outlet.	■ Use nonflammable cleaner.
■ Do not remove ground prong.	■ Keep flammable materials and vapors, such as gasoline,
■ Do not use an adapter.	away from refrigerator.
■ Do not use an extension cord.	■ Use two or more people to move and install refrigerator.
■ Disconnect power before servicing.	■ Disconnect power before installing ice maker (on ice maker
■ Replace all parts and panels before operating.	kit ready models only).
■ Replace all parts and panels before operating.
■ Remove doors from your old refrigerator.

SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm.

Proper Disposal of

Your Old Refrigerator

WARNING

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous

– even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

■Take off the doors.

■Leave the shelves in place so that children may not easily climb inside.

Important information to know about disposal of refrigerants:

Dispose of refrigerator in accordance with Federal and Local regulations. Refrigerants must be evacuated by a licensed, EPA certified refrigerant technician in accordance with established procedures.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

WARNING

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging

IMPORTANT: Do not remove the white foam air return insert from behind the control panel on the ceiling of the refrigerator. If the insert is removed, ice may migrate down from the freezer and cause icicles to form.

1.Using two or more people, tilt the refrigerator to one side. Remove the screws fastening the plastic runner to the bottom of the refrigerator. Repeat to remove the runner from the opposite side.

2.Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your fingers. Rinse with warm water and dry with a soft cloth.

NOTE: Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information see “Refrigerator Safety.”

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to cover the floor with cardboard or hardboard to avoid floor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or “walk” the refrigerator when trying to move it, as floor damage could occur.

Clean Before Using

After you remove all of the package materials, clean the inside of your refrigerator before using it. See the cleaning instructions in “Refrigerator Care.”

Important information to know about glass shelves and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

Location Requirements

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT: This refrigerator is designed for indoor, household use only.

To ensure proper ventilation for your refrigerator, allow ¹⁄ " (1.25 cm) of space on each side, and between the top of the refrigerator and overhead cabinets. Allow 2" (5 cm) of space

behind the refrigerator. If your refrigerator has an ice maker, allow extra space at the back for the water line connections. When installing your refrigerator next to a fixed wall, leave a 3¹⁄ " (8 cm) minimum space on the hinge side to allow the door to swing open.

NOTE: This refrigerator is intended for use in a location where the temperature ranges from a minimum of 55°F (13°C) to a maximum of 110°F (43°C). The preferred room temperature range for optimum performance, which reduces electricity usage and provides superior cooling, is between 60°F (15°C) and 90°F (32°C). It is recommended that you do not install the refrigerator near a heat source, such as an oven or radiator.

¹⁄ " (1.25 cm)

3¹⁄ " (8 cm)

Electrical Requirements

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 volt, 60 Hz, AC only, 15or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

NOTE: Before performing any type of installation or cleaning, or removing a light bulb, turn cooling off or turn the control (Thermostat, Refrigerator or Freezer Control depending on the model) to OFF, and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and turn cooling on or reset the control (Thermostat, Refrigerator or Freezer Control depending on the model) to the desired setting. See “Using the Controls.”

Water Supply Requirements

Read all directions before you begin.

IMPORTANT:

■If you turn the refrigerator on before the water line is connected, turn the ice maker OFF.

■All installations must meet local plumbing code requirements.

■Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain above freezing.

TOOLS NEEDED: Flat-blade screwdriver, ⁄ " and ¹⁄ " open-end wrenches or 2 adjustable wrenches, ¹⁄ " nut driver and drill bit, cordless drill. Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed.

NOTE: Your refrigerator dealer has a kit available with a ¹⁄ " (6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercing-type or ³⁄ "

(4.76 mm) saddle valve which reduces water flow and clogs more easily.

Water Pressure

A cold water supply with water pressure of between 30 and

120 psi (207 and 827 kPa) is required to operate the ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the ice maker is still not operating properly:

■Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

■Allow the storage tank on the reverse osmosis system to refill after heavy usage.

If you have questions about your water pressure, call a licensed, qualified plumber.

Connect the Water Supply

(on some models)

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line is connected, turn the ice maker OFF to avoid excessive noise or damage to the water valve.

Connect to Water Line

1.Unplug refrigerator or disconnect power.

2.Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3.Locate a ¹⁄ " to 1¹⁄ " (1.27 cm to 3.18 cm) vertical cold water pipe near the refrigerator.

IMPORTANT:

■Make sure it is a cold water pipe.

■Horizontal pipe will work, but drill on the top side of the pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

4.Determine the length of copper tubing you will need. Measure from the connection on lower left rear of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄ " (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5.Using a cordless drill, drill a ¹⁄ " hole in the cold water pipe you have selected.

	A
G	B
G
	C

F E	D
A. Cold water pipe	E. Compression sleeve
B. Pipe clamp	F. Shutoff valve
C. Copper tubing	G. Packing nut

D.Compression nut

6.Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the ¹⁄ " drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so washer makes a watertight seal. Do not overtighten.

7.Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

8.Place the free end of the tubing in a container or sink, and turn ON the main water supply. Flush the tubing until water is clear. Turn OFF the shutoff valve on the water pipe. Coil the copper tubing.

Connect to Refrigerator

NOTE: On kit models, assemble water valve to refrigerator according to kit instructions.

Style 1

1.Unplug refrigerator or disconnect power.

2.Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten.

3.Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown. This will help avoid damage to the tubing when the refrigerator is pushed back against the wall.

4.Turn shutoff valve ON.

5.Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

A. Tube clamp	D. Compression nut
B. Tube clamp screw	E. Valve inlet

C.Copper tubing

6.The ice maker is equipped with a built-in water strainer. If your water conditions require a second water strainer, install it in the ¹⁄" (6.35 mm) water line at either tube connection. Obtain a water strainer from your nearest appliance dealer.

Style 2

1.Unplug refrigerator or disconnect power.

2.Disconnect the tube clamp on the back of the product and insert the copper tubing through the clamp as shown.

3.Attach the copper tube to the valve inlet using a compression nut and sleeve as shown.

4.Tighten the compression nut. Do not overtighten. Reattach the tube clamp and tube to the back of the cabinet.

A. Tube clamp	C. Compression nut
B. Copper tubing

5.Turn shutoff valve ON. Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

Complete the Installation

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

NOTE: Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely fill ice container.

Refrigerator Doors

TOOLS NEEDED: ⁄" hex-head socket wrench, #2 Phillips screwdriver, flat-blade screwdriver, ⁄" open-end wrench, flat 2" putty knife.

IMPORTANT:

■Before you begin, turn the refrigerator control OFF. Unplug refrigerator or disconnect power.

■Remove food and adjustable door or utility bins from doors.

■If you are only removing and replacing the doors, see the “Remove Doors and Hinges” and “Replace Doors and Hinges” sections.

Remove Doors and Hinges

⁄" Hex-Head Hinge Screw

1.Unplug refrigerator or disconnect power.

2.Close the refrigerator door and keep both doors closed until you are ready to lift them free from the cabinet.

NOTE: Provide support between the freezer and refrigerator doors while the hinges are being moved. Do not depend on the door magnets to hold the doors in place while you are working.

3.Remove the parts for the top hinge as shown in Top Hinge graphic. Lift the freezer door free from the cabinet.

4.Remove the parts for the center hinge as shown in the Center Hinge graphic.

NOTE: Provide support between the refrigerator door and the floor while the hinges are being moved. Do not depend on the door magnets to hold the door in place while you are working.

5.Lift the refrigerator door free from the cabinet.

6.Remove the four screws (two on the bottom and two on the front) attaching the Bottom hinge to the cabinet. See Bottom Hinge graphic.

Reverse Doors (optional)

IMPORTANT: If you want to reverse your doors so that they open in the opposite direction, follow these steps. If you are not reversing the doors, see “Replace Doors and Hinges.”

Graphics follow these instructions.

Door Hinge	Cabinet Hinge
Hole Plug	Hole Plug

Cabinet

1.From the top of the cabinet, remove the hinge hole plugs, move them to the opposite side, and insert the hole plugs into the holes from where you removed the hinge screws. See Graphic 1-2.

2.Remove the screws filling the holes to be used for the Center Hinge and install them on the opposite side.

3.Move the leveler from the bottom of the refrigerator and install it on the opposite side.

4.Move the parts of the top hinge, center hinge and bottom hinge to the opposite side.

Doors

1.Remove door hinge hole plug from top of freezer door. Move to opposite side as shown. See Graphic 2.

2.Remove the door stop from the bottoms of both the freezer and refrigerator doors and install them on the opposite side. See graphics 3 and 4.

Replace Doors and Hinges

NOTES:

■Graphic may be reversed if door swing is reversed.

■Provide additional support for the doors while the hinges are being reinstalled. Do not depend on the door magnets to hold the doors in place while you are working.

1.Replace the parts for the bottom hinge as shown. Tighten screws. Replace the refrigerator door.

2.Assemble the parts for the center hinge as shown and tighten all screws. See Center Hinge graphic. Replace the freezer door.

3.Assemble the parts for the top hinge as shown. See Top Hinge graphic. Do not tighten screws completely.

4.Align the doors so that the bottom of the freezer door is even with the top of the refrigerator door. Tighten all screws.

Final Steps

1.Check all holes to make sure that hole plugs and screws are in place.

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

2.Plug into a grounded 3 prong outlet.

3.Reset the controls. See “Using the Control(s).”

4.Return all removable door parts to doors and food to refrigerator.

Whirlpool WRT111SFAA, WRT111SFAB, WRT111SFAW Owner's Manual

Door Removal &	Door Swing Reversal (optional)
Replacement
Top Hinge	1-1
Top Hinge
A
	A
B	A. 5/16" Hex-Head Hinge
	Screws and Washers
C	1-2
	1-2

A. 5/16" Hex-Head Hinge Screws

B. Top Hinge

A. Cabinet Hinge Hole Plugs

C. Spacer

Center Hinge

A.Center Hinge

B. 5/16" Hex-Head Hinge Screws

Bottom Hinge

A.Bottom Hinge

B.5/16" Hex-Head Hinge Screws

C.Leveler

A. Door Hinge Hole Plug

3	Removal of Door Stops
	Removal of Door Stops
	A
	B

A.Door Stop

B.Door Stop Screw

4 Reinstallation of Door Stops

A B

A.Door Stop

B.Door Stop Screw

Adjust the Doors

WARNING

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Your refrigerator has two adjustable levelers, one on each side, at the base of the refrigerator. If your refrigerator seems unsteady or if you want the doors to close more easily, adjust the level and tilt of the refrigerator.

1.Turn the leveler to the left to raise that side of the refrigerator or to the right to lower that side. It may take several turns to adjust the tilt of the refrigerator.

NOTE: Having someone push against the top of the refrigerator takes some weight off the levelers. This makes it easier to turn the levelers.

2.Open both doors again to make sure that they close as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning both levelers to the right. It may take several more turns.

NOTE: To keep the refrigerator level, make the same adjustment to each side.

3.Using a level, make sure the refrigerator is still level from side to side. Readjust if necessary.

IMPORTANT:

■Turning the Temperature Control to OFF stops cooling in the refrigerator and freezer compartments, but it does not disconnect the refrigerator from the power supply.

■The Temperature Control regulates the temperature in both the refrigerator and freezer compartments. Settings to the left of the mid-setting make the temperature less cold. Settings to the right of the mid-setting make the temperature colder.

■Wait 24 hours before you put food into your refrigerator. If you add food before the refrigerator has cooled completely, your food may spoil.

NOTE: Adjusting the Temperature Control to a higher (colder) setting will not cool the compartments any faster.

■The mid-settings should be correct for normal household usage. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm.

■If the temperature is too warm or too cold in the refrigerator or freezer, before adjusting the controls, first make sure the air vents are not blocked.

Adjust the Temperature Control

NOTE: Wait at least 24 hours between adjustments and then recheck the temperatures.

CONDITION/REASON:	ADJUSTMENT:

REFRIGERATOR too warm	Temperature Control
	one setting higher

FREEZER too warm/too little ice	Temperature Control
	one setting higher

REFRIGERATOR too cold	Temperature Control
	one setting lower

FREEZER too cold	Temperature Control
	one setting lower

Air Flow Control

The Air Flow control is located on the back wall of the freezer. It regulates the amount of air flowing between the freezer and the refrigerator compartments.

When you plug in the refrigerator for the first time, turn the Air Flow control to the Recommended setting.

REFRIGERATOR USE

Using the Controls

Temperature Control

When you plug in the refrigerator for the first time, set the Temperature Control to the Middle dot. Temperature Control adjustments range from MIN (least cold) to MAX (coldest).

Adjust the Air Flow Control

If you want to temporarily increase the cold air flow to a specific compartment, adjust the control.

IMPORTANT: Once the performance is achieved, return the Air Flow control to the Recommended setting to keep the refrigerator operating at optimum efficiency.

CONDITION/REASON:	ADJUSTMENT:

Heavy ice use	Max Freezer

Hot room temperature	Max Freezer - To maintain ice
	making production rate

Large quantity of groceries	Max Refrigerator - To quickly
	chill food and beverages

Crisper Humidity Control (on some models)

You control the amount of humidity in the moisture-sealed crisper. Depending on the produce you are storing, select the desired Humidity Level.

Humidity Level - Min Setting

MIN (open) lets moist air out of the crisper for best storage of fruits and vegetables with skins.

■Fruit: Wash, let dry and store in refrigerator in plastic bag or crisper. Do not wash or hull berries until they are ready to use. Sort and keep berries in original container in crisper, or store in a loosely closed paper bag on a refrigerator shelf.

■Vegetables with skins: Place in plastic bag or plastic container and store in crisper.

MAX (closed) keeps moist air in the crisper for best storage of fresh, leafy vegetables.

Leafy vegetables: Wash in cold water, drain and trim or tear off bruised and discolored areas. Place in plastic bag or plastic container and store in crisper.

Ice Maker

(on some models - Accessory)

Turning the Ice Maker On/Off

NOTE: Do not force the wire shutoff arm up or down.

■To turn the ice maker on, simply lower the wire shutoff arm.

NOTE: Your ice maker has an automatic shutoff. As ice is made, the ice cubes will fill the ice storage bin and the ice cubes will raise the wire shutoff arm to the OFF (arm up) position.

■To manually turn off the ice maker, lift the wire shutoff arm to the OFF (arm up) position and listen for the click to make sure the ice maker will not continue to operate.

MAX

NORMAL

NOTE: Turn off the ice maker before removing the ice storage bin to serve ice or to clean the bin. This will keep the ice cubes from dropping out of the ice maker and into the freezer compartment. After replacing the ice storage bin, turn on the ice maker.

Ice Production Rate

In normal operation, the ice maker should produce approximately 8 to 12 batches of ice in a 24-hour period.

If ice is not being made fast, enough adjust the controls.

■Air Flow Control - Turn the control dial to the Max Freezer setting.

■Temperature Control - Turn the control dial gradually toward the Max setting, waiting 24 hours between each increase.

Remember

■Allow 24 hours to produce the first batch of ice. Allow 3 days to completely fill the ice storage bin. Discard the first three batches of ice produced.

■The quality of your ice will be only as good as the quality of the water supplied to your ice maker. Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well maintained.

■Do not store anything on top of the ice maker or in the ice storage bin.

REFRIGERATOR

FEATURES

Your model may have some or all of these features.

Important information to know about glass shelves and covers:

Refrigerator Shelves

(Glass shelves on some models)

The shelves in your refrigerator are adjustable to match your individual storage needs.

Storing similar food items together in your refrigerator and adjusting the shelves to fit different heights of items will make finding the exact item you want easier. It will also reduce the amount of time the refrigerator door is open, and save energy.

Shelves and Glass Shelves (on some models)

To remove and replace a shelf:

1.Remove items from the shelf.

2.Slide the shelf straight out to the stop.

3.Depending on your model, lift back or front of the shelf past the stop. Slide shelf out the rest of the way.

4.Replace the shelf by sliding the back of the shelf into the track in the wall of the cabinet.

5.Guide the front of the shelf into the shelf track. Be sure to slide the shelf in all the way.

Meat Drawer

(on some models)

To remove and replace the meat drawer:

1.Slide meat drawer out to the stop.

2.Lift front of meat drawer with one hand while supporting bottom of drawer with other hand. Slide drawer out the rest of the way.

3.Replace the drawer by sliding it back in fully past the drawer stop.

Meat Drawer Cover (on some models)

To remove and replace the meat drawer cover:

1.Remove the meat drawer.

2.Push the cover back to release the rear clips from the shelf. Tilt the cover up at the front, and pull it forward.

3.Replace the meat drawer cover by fitting the notches and clips on the cover over the rear and center crossbars on the shelf.

4.Lower cover into place and pull the cover forward to secure the rear clips onto the shelf.

5.Replace the meat drawer.

NOTE: In some models the meat pan moves sideways on the shelf to allow for flexible positioning.

Meat Storage Guide

Store most meat in original wrapping as long as it is airtight and moisture-proof. Rewrap if necessary. See the following chart for storage times. When storing meat longer than the times given, freeze the meat.

Fresh fish or shellfish ........................	use same day as purchased
Chicken, ground beef, variety meats (liver)		...................... 1-2 days
Cold cuts, steaks/roasts ..................................................		3-5 days
Cured meats ..................................................................		7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or plastic containers with tight lids.

Crisper

(on some models)

Crisper Drawers

To remove and replace the crisper drawer:

1.Slide the crisper drawer straight out to the stop. Lift the front and slide the drawer out the rest of the way.

2.Replace the drawer by sliding the drawer in fully past the stop.

Crisper Cover

Style 1 - Plastic Cover

To remove and replace the crisper cover: 1. Remove the crisper(s).

2.Lift the front of the cover to remove the cover support. Then lift the cover up and slide it out.

3.Replace the cover by fitting the cover tabs into lowest cabinet slots and pushing them in. Lower the front retainers into place.

4.Insert cover support (with the long tab toward the front) into the groove on the underside of the cover.

NOTE: If the support needs adjustment, turn the base of the support clockwise to raise or counterclockwise to lower.

Style 2 - Glass Cover

To remove and replace the crisper cover:

1.Pull the glass straight out.

2.Replace the glass by pushing it straight in.

Utility or Egg Bin

(on some models)

Depending on your model, you may have a one, two or three piece bin. Eggs may be stored in the egg tray or loose in the bin.

NOTE: Store eggs in a covered container for long-term storage. If your model does not have an egg storage bin, store eggs in their original container on an interior shelf.

+ 22 hidden pages