Whirlpool KRBL102ESS, KRBR102ESS, KRBL109ESS, KRBR109ESS, MBL1957FEZ Owner's Manual
...
BOTTOM-MOUNT REFRIGERATOR OWNER’S
MANUAL
MANUEL D’UTILISATION DU RÉFRIGÉRATEUR AVEC
CONGÉLATEUR EN BAS
Table of Contents/Table des matières
REFRIGERATOR SAFETY.................................................2
Refrigerator Safety......................................................... 2
MAINTENANCE AND CARE ..............................................3
Cleaning ......................................................................3
Changing the LED Module ............................................... 3
Water Filtration System ...................................................3
Vacation and Moving Care ...............................................4
INSTALLATION INSTRUCTIONS ........................................ 4
Unpack the Refrigerator .................................................. 4
Electrical Requirements ..................................................5
Location Requirements ...................................................5
Water Supply Requirements.............................................5
Connect the Water Supply ...............................................6
REFRIGERATOR FEATURES............................................. 7
Crisper Humidity Control ................................................. 7
DOOR AND HANDLE INSTRUCTIONS ................................ 7
Refrigerator Doors and Drawer ......................................... 7
Remove and Replace Door Handles .................................. 7
Remove Doors and Hinges .............................................. 9
Reverse Doors (optional)............................................... 11
Replace Doors and Hinges ............................................ 11
Remove and Replace Freezer Drawer.............................. 13
PERFORMANCE DATA SHEET ........................................ 15
SÉCURITÉ DU RÉFRIGÉRATEUR .................................... 17
Sécurité du réfrigérateur................................................ 17
ENTRETIEN ET RÉPARATION ......................................... 18
Nettoyage .................................................................. 18
Remplacer le module à DEL........................................... 19
Système de filtration de l’eau.......................................... 19
Précautions à prendre avant les vacances ou le
déménagement ........................................................... 19
INSTRUCTIONS D’INSTALLATION ................................... 20
Déballage du réfrigérateur ............................................. 20
Spécifications électriques .............................................. 20
Exigences d’emplacement ............................................. 21
Spécifications de l’alimentation en eau ............................. 21
Raccordement à la canalisation d’eau .............................. 21
CARACTÉRISTIQUES DU RÉFRIGÉRATEUR..................... 23
Réglage de l’humidité dans le tiroir à légumes .................... 23
INSTRUCTIONS POUR LA PORTE ET LA POIGNÉE............ 23
Portes et tiroir du réfrigérateur ........................................ 23
Consulter la section Retrait et réinstallation des poignées de
porte ......................................................................... 24
Démontage des portes et charnières................................ 25
Inversion des portes (facultatif) ....................................... 27
Réinstallation des portes et charnières ............................. 28
Retrait et réinstallation du tiroir de congélation ................... 30
FICHE DE DONNÉES RELATIVES AU RENDEMENT ........... 32
W11479841A
REFRIGERATOR SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These
words mean:
You can be killed or seriously injured if you don't
DANGER
immediately follow instructions.
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
You can be killed or seriously injured if you don’t follow
instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions,
including the following:
� Children should be supervised to ensure that they do not
play with the appliance.
� This appliance is not intended for use by persons (including
children) with reduced physical, sensory, or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their
safety.
� Do not use an extension cord.
� If power supply cord is damaged, it must be replaced by the
manufacturer, its service agent, or a similarly qualified
person in order to avoid a hazard.
� Connect to potable water supply only.
� This appliance is intended to be used in household and
similar applications such as: staff kitchen areas in shops,
offices, and other working environments; farm houses and
by clients in hotels, motels, and other residential-type
environments; bed and breakfast-type environments; and
catering and similar non-retail applications.
� Do not store explosive substances such as aerosol cans
with a flammable propellant in this appliance.
� Do not use replacement parts that have not been
recommended by the manufacturer (e.g., parts made at
home using a 3D printer).
� Keep the ventilation openings, in the appliance enclosure
or in the built-in structure, clear of obstruction.
� Do not use mechanical devices or other means to
accelerate the defrosting process, other than those
recommended by the manufacturer.
� Do not damage the refrigerant circuit.
� Do not use electrical appliances inside the food storage
compartments of the appliance, unless they are of the type
recommended by the manufacturer.
SAVE THESE INSTRUCTIONS
Proper Disposal of Your Old Refrigerator
WARNING: Risk of child entrapment. Before you throw away
your old refrigerator or freezer:
� Take off the doors.
� Leave the shelves in place so that children may not easily
climb inside.
WARNING
Suffocation Hazard
Remove doors or lid from your old appliance.
Failure to do so can result in death or brain damage.
2
IMPORTANT: Child entrapment and suffocation
are not problems of the past. Junked or
abandoned refrigerators are still dangerous,
even if they will sit for “just a few days.” If you are
getting rid of your old refrigerator, please follow
these instructions to help prevent accidents.
Important information to know about
disposal of refrigerants:
Dispose of refrigerator in accordance with
federal and local regulations. Refrigerants must
be evacuated by a licensed, EPA-certified
refrigerant technician in accordance with
established procedures.
MAINTENANCE AND CARE
Cleaning
WARNING
Explosion Hazard
Risk of Fire or Explosion.
Flammable Refrigerant Used.
Do Not Use Mechanical Devices to Defrost Refrigerator.
Do Not Puncture Refrigerant Tubing.
Both the refrigerator and freezer sections defrost automatically.
However, clean both sections about once a month to avoid odor
buildup. Wipe up spills immediately.
IMPORTANT:
� Because air circulates between both sections, any odors
formed in one section will transfer to the other. You must
thoroughly clean both sections to eliminate odors. To avoid
odor transfer and drying out of food, wrap or cover foods
tightly.
� For stainless steel models, stainless steel is corrosion-
resistant and not corrosion-proof. To help avoid corrosion of
your stainless steel, keep your surfaces clean by using the
following cleaning instructions.
To Clean Your Refrigerator:
NOTE: Do not use abrasive or harsh cleaners such as window
sprays, scouring cleansers, flammable fluids, muriatic acid,
cleaning waxes, concentrated detergents, bleaches, or cleansers
containing petroleum products on exterior surfaces (doors and
cabinet), plastic parts, interior, and door liners or gaskets. Do not
use paper towels, scouring pads, or other harsh cleaning tools.
1. Unplug refrigerator or disconnect power.
2. Hand-wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a
mild detergent in warm water.
3. Clean the exterior surfaces.
Painted metal: Wash painted metal exteriors with a clean,
soft cloth or sponge and a mild detergent in warm water. Rinse
surfaces with clean, warm water and dry immediately to avoid
water spots.
Stainless steel: Wash stainless steel surfaces with a clean,
soft cloth or sponge and a mild detergent in warm water. Rinse
surfaces with clean, warm water and dry immediately to avoid
water spots.
NOTE: When cleaning stainless steel, always wipe with the
grain to avoid cross-grain scratching.
WARNING
Explosion Hazard
Risk of Fire or Explosion due to Puncture of Refrigerant
Tubing;
Follow Handling Instructions Carefully.
Flammable Refrigerant Used.
4. There is no need for routine condenser cleaning in normal
home operating environments. If the environment is
particularly greasy or dusty, or there is a significant pet traffic
in the home, the condenser should be cleaned every 2 to 3
months to ensure maximum efficiency.
If you need to clean the condenser:
� Pull refrigerator out away from the wall. See “Unpack the
Refrigerator.”
� Remove the base grille.
� Vacuum coils when they are dusty or dirty.
� Replace the base grille when finished.
� Roll refrigerator back into place. Make sure to leave 1"
(2.5 cm) between the cabinet back and the wall.
� Check to see that the refrigerator is level.
5. Plug in refrigerator or reconnect power.
Changing the LED Module
IMPORTANT: The lights in both the refrigerator and freezer
compartments use LED technology that do not need to be
replaced.
If an LED module(s) do not illuminate when the refrigerator and/or
freezer door is opened, call for assistance or service. See "Quick
Start Guide" for contact information.
Water Filtration System
The water filter is located in the upper right-hand corner of the
refrigerator compartment.
Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the
system. Systems certified for cyst reduction may be used on
disinfected waters that may contain filterable cysts.
IMPORTANT: The disposable water filter should be replaced at
least every 6 months. If the water flow to the water dispenser or
ice maker decreases noticeably before 6 months have passed,
replace the water filter more often.
Water Filter Status Lights
The water filter status lights will help you know when to change
the water filter. When the Order light is on, it is almost time to
change the water filter. When the Replace light is on, a new water
filter should be installed.
3
Reset Water Filter Status (on some models)
After replacing the water filter, press and hold Filter Reset for 3
seconds until the Order or Replace light turns off. See "Using the
Controls" in the Quick Start Guide.
Replacing the Water Filter
To purchase replacement water filter, model EDR4RXD1/
EDR4RXD1B, UKF8001AXX-750 or UKF8001AXX-200, contact
your dealer or call 1-800-253-1301 U.S.A. or 1-800-807-6777
Canada.
IMPORTANT: Air trapped in the water system may cause water
and filter to eject. Always dispense water for at least 2 minutes
before removing the filter or blue bypass cap.
1. Turn filter counterclockwise to remove.
NOTE: There may be some water in the filter. Some spilling
may occur. Use a tower to wipe up any spills.
2. Remove sealing label from replacement filter and insert the
filter end into the filter head.
3. Turn the filter clockwise until it stops. Snap the filter cover
closed.
4. Flush the water system. See “Water Dispenser.”
NOTE: The dispenser feature may be used without a water
filter installed. Your water will not be filtered. If this option is
chosen, replace the filter with the blue bypass cap.
2. Remove all food from the refrigerator and pack all frozen food
in dry ice.
3. Empty the ice bin.
4. Turn off the Temperature control(s). See “Using the Controls”
in the Quick Start Guide.
5. Unplug refrigerator.
6. Clean, wipe, and dry thoroughly.
7. Take out all removable parts, wrap them well, and tape them
together so they don’t shift and rattle during the move.
8. Depending on the model, raise the front of the refrigerator so it
rolls more easily or raise the leveling screws so they don’t
scrape the floor. See online “Adjust the Door(s)” or “Door
Closing and Door Alignment.”
9. Tape the doors closed and tape the power cord to the back of
the refrigerator.
When you get to your new home, put everything back and refer to
“Installation Instructions” for preparation instructions. If your
refrigerator has an automatic ice maker, remember to reconnect
the water supply to the refrigerator.
INSTALLATION INSTRUCTIONS
Unpack the Refrigerator
Vacation and Moving Care
Vacations
If You Choose to Leave the Refrigerator On While You’re
Away:
1. Use up any perishables and freezer other items.
2. If your refrigerator has an automatic ice maker, and is
connected to the household water supply, turn off the water
supply to the refrigerator. Property damage can occur if the
water supply is not turned off.
3. If you have an automatic ice maker, turn off the ice maker.
NOTE: Raise the wire shutoff arm to Off (arm up) position.
4. Empty the ice bin.
If You Choose to Turn Off the Refrigerator Before You Leave:
1. Remove all food from the refrigerator.
2. If your refrigerator has an automatic ice maker:
� Turn off the water supply to the ice maker at least one day
ahead of time.
� When the last load of ice drops, raise the wire shutoff arm
to the Off (up) position.
3. Empty the ice bin.
4. Turn off the Temperature control(s). See “Using the Controls”
in the Quick Start Guide.
5. Clean refrigerator, wipe it, and dry well.
6. Tape rubber or wood blocks to the tops of both doors to prop
them open far enough for air to get in. This stops odor and
mold from building up.
Moving
When you are moving your refrigerator to a new home, follow
these steps to prepare it for the move.
1. If your refrigerator has an automatic ice maker:
� Turn off the water supply to the ice maker at least one day
ahead of time.
� Disconnect the water line from the back of the refrigerator.
� When the last load of ice drops, raise the wire shutoff arm
to the Off (up) position.
WARNING
Excessive Weight Hazard
Use two or more people to move and install or uninstall
appliance.
Failure to do so can result in back or other injury.
Remove the Packaging
� Remove tape and glue residue from surfaces before turning on
the refrigerator. Rub a small amount of liquid dish soap over
the adhesive with your fingers. Wipe with warm water and dry.
� Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your refrigerator. For
more information, see “Refrigerator Safety.”
� Dispose of/recycle all packaging materials.
When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator for
cleaning or service, be sure to cover the floor with cardboard or
hardboard to avoid floor damage. Always pull the refrigerator
straight out when moving it. Do not wiggle or “walk” the
refrigerator when trying to move it, as floor damage could occur.
Clean Before Using
After you remove all of the packaging materials, clean the inside
of your refrigerator before using it. See the cleaning instructions in
the “Maintenance and Care” section of your Owner’s Manual.
Important information to know about glass shelves and
covers:
Do not clean glass shelves or covers with warm water when they
are cold. Shelves and covers may break if exposed to sudden
temperature changes or impact, such as bumping. Tempered
glass is designed to shatter into many small, pebble-size pieces.
This is normal. Glass shelves and covers are heavy. Use both
hands when removing them to avoid dropping.
4
Electrical Requirements
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical connection.
If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified person.
Do not use a cord that shows cracks or abrasion damage along its
length or at either the plug or connector end.
Recommended Grounding Method
A 115 V, 60 Hz, AC-only 15 A or 20 A fused, grounded electrical
supply is required. It is recommended that a separate circuit
serving only your refrigerator and approved accessories be
provided. Use an outlet that cannot be turned off by a switch. Do
not use an extension cord.
NOTE: Before performing any type of installation, cleaning, or
removing a light bulb, turn the refrigerator to OFF. Depending on
your model, turn the refrigerator control to the word OFF, or press
the refrigerator down arrow touch pad until a dash (–) appears in
refrigerator displays as shown. Disconnect the refrigerator from
the electrical source. When you are finished, reconnect the
refrigerator to the electrical source and reset the temperature
controls to the desired setting. See “Quick Start Guide.”
� Staff kitchen areas in shops, offices and other working
environments.
� Farm houses and by clients in hotels, motels and other
residential type environments.
� Bed and breakfast type environments.
� Catering and similar non-retail applications.
To ensure proper ventilation for your refrigerator, allow for 1/2"
(1.25 cm) of space on each side and at the top. Allow for 1"
(2.54 cm) of space behind the refrigerator. If your refrigerator has
an ice maker, allow extra space at the back for the water line
connections. When installing your refrigerator next to a fixed wall,
leave 2 1/2" (6.3 cm) minimum on the hinge side (some models
require more) to allow for the door to swing open.
NOTE: This refrigerator is intended for use in a location where the
temperature ranges from a minimum of 55°F (13°C) to a
maximum of 110°F (43°C). The preferred room temperature range
for optimum performance, which reduces electricity usage and
provides superior cooling, is between 60°F (15°C) and 90°F
(32°C). It is recommended that you do not install the refrigerator
near a heat source, such as an oven or radiator.
Water Supply Requirements
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Location Requirements
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as gasoline,
away from appliance.
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.
IMPORTANT: This refrigerator is designed for indoor, household
use only.
This appliance is intended to be used in a household and similar
applications such as:
Tools Needed:
� Flat-blade screwdriver
� 7/16" and 1/2" Open-end or two
adjustable wrenches
IMPORTANT:
� Connect to a potable water supply only.
Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after
the system. Systems certified for cyst reduction may be used
on disinfected waters that may contain filterable cysts.
� All installations must meet local plumbing code requirements.
� Do not use a piercing-type or 3/16 " (4.76 mm) saddle valve
which reduces water flow and clogs more easily.
� Use copper tubing and check for leaks. Install copper tubing
only in areas where the household temperatures will remain
above freezing.
� For models with water filters, the disposable water filter should
be replaced at least every 6 months.
� 1/4" Nut driver
� 1/4" Drill bit
� Cordless drill
5
Water Pressure
A cold water supply with water pressure of between 35 and 120
psi (241 and 827 kPa) is required to operate the water dispenser
and ice maker. If you have questions about your water pressure,
call a licensed, qualified plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 35 and 120 psi (241 and
827 kPa).
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).
If the water pressure to the reverse osmosis system is less than
40 to 60 psi (276 to 414 kPa):
IMPORTANT: Flush the water system before calibrating
Measured Fill. See “Flush the Water System” in the Owner’s
Manual.
If you have questions about your water pressure, call a licensed,
qualified plumber.
Connect the Water Supply
Read all directions before you begin.
IMPORTANT:
� Plumbing shall be installed in accordance with the
International Plumbing Code and any local codes and
ordinances.
� The water tubing on the back of the refrigerator (which is used
to connect to the household water line) is a PEX (cross-linked
polyethylene) tube. Copper and PEX tubing connections from
the household water line to the refrigerator are acceptable, and
will help avoid off-taste or odor in your ice or water. Check for
leaks. If PEX tubing is used instead of copper, we recommend
contacting Service to obtain current part numbers.
� Install tubing only in areas where temperatures will remain
above freezing.
� If you turn on the refrigerator before the water line is
connected, turn off the ice maker to avoid excessive noise or
damage to the water valve.
Connect to Water Line
1. Unplug refrigerator or disconnect power.
2. Turn off main water supply. Turn on nearest faucet long
enough to clear line of water.
3. Find a 1/2" to 1 1/4" (12.7 mm to 31.8 mm) vertical cold water
pipe near the refrigerator.
� Make sure it is a cold water pipe.
� Horizontal pipe will work, but the following procedure must
be followed: Drill on the top side of the pipe, not the
bottom. This will help keep water away from the drill. This
also keeps normal sediment from collecting in the valve.
4. Determine the length of copper tubing you need. Measure
from the connection on the lower right rear of the refrigerator
to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use
1/4" (6.35 mm) O.D. (outside diameter) copper or PEX tubing.
Be sure both ends of copper or PEX tubing are cut square.
5. Using a cordless drill, drill a 1/4" (6.35 mm) hole in the cold
water pipe you have selected.
A. Cold water pipe
B. Pipe clamp
C. Copper or PEX tubing
D. Compression nut
6. Fasten the shutoff valve to the cold water pipe with the pipe
clamp. Be sure the outlet end is solidly in the 1/4" (6.35 mm)
drilled hole in the water pipe and that the washer is under the
pipe clamp. Tighten the packing nut. Tighten the pipe clamp
screws slowly and evenly so the washer makes a watertight
seal. Do not overtighten.
7. Slip the compression sleeve and compression nut on the
copper tubing as shown. Insert the end of the tubing into the
outlet end squarely as far as it will go. Screw compression nut
onto outlet end with adjustable wrench. Do not overtighten or
you may crush the copper tubing.
8. Place the free end of the tubing in a container or sink, and turn
on the main water supply. Flush the tubing until water is clear.
Turn off the shutoff valve on the water pipe.
E. Compression sleeve
F. Shutoff valve
G. Packing nut
Connect to Refrigerator
Depending on your model, the water line may come down from
the top or up from the bottom. Follow the connection instructions
for your model.
Style 1
1. Remove plastic cap from water valve inlet port. Attach the
copper tube to the valve inlet using a compression nut and
sleeve as shown. Tighten the compression nut. Do not
overtighten. Confirm copper tubing is secure by pulling on
copper tubing.
2. Create a service loop with the copper tubing. Avoid kinks
when coiling the tubing. Secure copper or PEX tubing to
refrigerator cabinet with a “P” clamp.
A. Copper or PEX
tubing
B. “P” clamp
C.
Compression nut
D. Compression sleeve
3. Turn on water supply to refrigerator and check for leaks.
Correct any leaks.
Style 2
1. Create a service loop (minimum diameter of 2 ft. [61 cm]) with
the copper or PEX tubing. Avoid kinks when coiling the tubing.
6
2. Remove the plastic cap from water valve inlet port. Place a
compression nut and sleeve on the copper or PEX tubing.
3. Insert the end of the copper or PEX tubing into the water valve
inlet port. Shape tubing slightly so that the tubing feeds
straight into the port to avoid kinks.
4. Slide the compression nut over the sleeve and screw into the
water valve inlet port.
A. PEX water tubing
B. Sleeve
5. Using an adjustable wrench, hold the nut on the plastic water
line to keep it from moving. Then, with a second wrench turn
the compression nut on the copper tubing counterclockwise to
completely tighten. Do not overtighten.
A. “P” clamp
B. PEX water line
6. Check connection by pulling on tubing. Attach the PEX water
line to the refrigerator cabinet with a “P” clamp.
7. Turn on water supply to the refrigerator and check for leaks.
Correct any leaks.
C. Compression nut
D. Copper or PEX tubing
C. Compression nut
D. Copper tubing
REFRIGERATOR FEATURES
Crisper Humidity Control
You can control the amount of humidity in the moisture-sealed
crisper. Depending on your model, adjust the control to any setting
between Fruit and Vegetables or Low and High.
� Fruit/Low (open) for best storage of fruits and vegetables with
skins.
� Vegetables/High (closed) for best storage of fresh, leafy
vegetables.
For information on additional features for your appliance, see
online "Feature Guide."
DOOR AND HANDLE INSTRUCTIONS
Refrigerator Doors and Drawer
TOOLS NEEDED: 5/16", 3/8", 1/4" hex head socket wrench, a
Torx† T20 screwdriver, a #2 Phillips screwdriver, and a flat-blade
screwdriver
IMPORTANT:
� Your refrigerator may have a standard reversible refrigerator
door with either a freezer door or freezer drawer, or French
doors. Follow the instructions specific to the door style of your
model.
� If you only want to remove and replace the doors, see
“Remove Doors and Hinges” and “Replace Doors and Hinges.”
� Before you begin, turn the refrigerator control Off, and remove
food and adjustable door or utility bins from the doors.
Remove and Replace Door Handles
REFRIGERATOR DOOR HANDLES
Refrigerator Door Handle Style 1
Complete the Installation
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
1. Plug into a grounded 3–prong outlet.
NOTE: Allow 24 hours to produce the first batch of ice.
Discard the first three batches of ice produced. Allow 3 days to
completely fill the ice storage bin.
2. Flush the water system. See “Water and Ice Dispensers.”
A. 3/32” Setscrew
� Using a 3⁄32" or 1⁄8" hex key, loosen the two setscrews located
on the side of each handle. Pull the handle straight out from
the drawer. Make sure you keep the screws for reattaching the
handles.
� To replace the handles, reverse the directions.
7
Refrigerator Door Handle Style 2
A. Handle Trim C. Refrigerator Door Handle
B. Flat–Head Handle Screws
� Remove the screw cover.
� Remove the handle assembly. Keep all parts together.
� To replace the handles, reverse the directions.
Refrigerator Door Handle Style 3
� To remove the handle, remove the screw attaching the trim to
the upper end of the handle. Using a flat-blade screwdriver
wrapped in masking tape, pry the trim piece from the lower end
of the handle. Then, remove the screws attaching the handle
to the door.
� To replace handle, reverse directions.
Refrigerator Door Handle Style 5
� To remove the handle, grasp the lower part of the handle
firmly, slide the handle up and pull the handle straight out from
the door.
� To replace the handle, position the handle so that the large
holes in the mounting clips are down and align the holes with
the door studs. Rotate the handle so that the mounting clips
are flat against the door and slide the handle down to engage.
FREEZER DOOR HANDLES
Freezer Door Handle Style 1
A. Flat–Head Handle Screws B. Refrigerator Door Handle
� Using a 3⁄32" or 1⁄8" hex key, loosen the two setscrews located
on the side of each handle. Pull the handle straight out from
the drawer. Make sure you keep the screws for reattaching the
handles.
� To replace the handles, reverse the directions.
Refrigerator Door Handle Style 4
A. Trim Screw C. Top Trim
B. Handle Screws D. Bottom Trim
A. 3/32” Setscrew
� Using a 3⁄32" or 1⁄8" hex key, loosen the two setscrews located
on the side of each handle. Pull the handle straight out from
the drawer. Make sure you keep the screws for reattaching the
handles.
� To replace the handles, reverse the directions.
Freezer Door Handle Style 2
A. Handle Trim C. Freezer Drawer Handle
B. Flat–Head Handle Screws
� Remove the screw cover.
� Remove the handle assembly. Keep all parts together.
� To replace the handles, reverse the directions.
8
Freezer Door Handle Style 3
A. Flat–Head Handle Screws
� Remove screws and handle.
� To replace handle, reverse directions.
Freezer Door Handle Style 4
A. Flat–Head Screws B. Freezer Drawer Handle
� Remove screws and handle.
� To replace the handles, reverse the directions.
Freezer Door Handle Style 5
3. Remove the parts for the top hinge as shown below. Lift the
refrigerator door free from the cabinet.
A. Hinge Cover Screw C. 5/16” Hex-Head Hinge Screws
B. Top Hinge Cover D. Top Hinge
4. Remove the parts for the bottom hinge as shown below.
� To remove the handle, grasp the lower part of the handle
firmly, slide the handle up and pull the handle straight out from
the door.
� To replace the handle, position the handle so that the large
holes in the mounting clips are down and align the holes with
the door studs. Rotate the handle so that the mounting clips
are flat against the door and slide the handle down to engage.
Remove Doors and Hinges
STANDARD DOOR
Hex Head Top Hinge Screw
Standard Door - Freezer drawer models
1. Unplug refrigerator or disconnect power
2. Keep the refrigerator door closed until you are ready to lift it
free from the cabinet.
NOTE: Provide additional support for the door while the
hinges are being moved. Do not depend on the door gasket
magnets to hold the door in place while you are working.
A. Hinge Pin Cover C. Hinge Screws
B. Bottom Hinge
Freezer door models
1. Unplug refrigerator or disconnect power.
2. Keep the freezer door closed until you are ready to lift it free
from the cabinet.
NOTE: Provide additional support for the door while the
hinges are being moved. Do not depend on the door gasket
magnets to hold the door in place while you are working.
3. Remove the parts for the top hinge as shown below. Lift the
refrigerator door free from the cabinet.
A. Hinge Cover Screw C. 5/16” Hex-Head Hinge Screws
B. Top Hinge Cover D. Top Hinge
9
4. Remove the center hinge pin and remove the hinge screws as
shown below. Lift the freezer door free from the cabinet.
A. Hinge Pin Cover C. Hinge Screws
B. Center Hinge
5. Remove the base grille by grasping the grille firmly with both
hands and pulling it toward you.
6. Remove the parts for the bottom hinge as shown below.
3. Starting with the right-hand side door, remove the parts for the
top hinge as shown below. Lift the refrigerator door from the
bottom hinge pin.
A. Hinge Cover Screw C. 5/16” Hex-Head Hinge Screws
B. Top Hinge Cover D. Top Hinge
4. Remove the hinge pin cover from the bottom hinge pin and
keep it for later use.
5. Before removing the left-hand side door, disconnect the wiring
plug located on top of the top hinge by wedging a flatblade
screwdriver or your fingernail between the two sections..
A. Hinge Pin Shim D. Roller Bracket
B. Bottom Hinge E. 3/8” Hex-Head Screws
C. Hinge Plate
WARNING
Electrical Shock Hazard
Disconnect power before removing doors.
Failure to do so could result in death or electrical shock.
FRENCH DOORS
1. Unplug refrigerator or disconnect power.
2. Keep the refrigerator doors closed until you are ready to lift
them free from the cabinet.
NOTE: Provide additional support for the refrigerator door
while the hinges are being removed. Do not depend on the
door gasket magnets to hold the door in place while you are
working
NOTE: The green, ground wire remains attached to the hinge.
6. Remove the parts for the left-hand side door top hinge as
shown in the Top Hinge graphic in Step 3. Lift the door from
the bottom hinge pin.
NOTE: Remove the hinge pin cover from the bottom hinge pin
and keep it for later use.
A. Hinge Pin Cover C. Hinge Screws
B. Bottom Hinge
10
Loading...