WHIRLPOOL WP 122 User Manual

5019 396 03782

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!

THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY BUTTON EXCEPT CANCEL/OFF BUTTON.

FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.

PROGRAM SELECTION BUTTON

Push “P” button (repeatedly) until selected program number is shown on the display (P1...Px) see “Table of programs” next page).

DELAYED START BUTTON

Push the button (repeatedly) to delay the start of the program. Adjustable from 1 to 24 hours. With each press of the button, the delayed start indicator increases by one hour and after 24 restarts from 0. Then press the START button. The dishwasher will start after the set time.

POWER CLEAN

Thanks to the additional power jets this option provides a more intensive and powerful wash in the lower rack, in the specific area. This option is recommended for washing pots and casseroles (see page 7). Press this button to activate Power Clean (the indicator lights up). For non Power Clean loading to achieve best cleaning performances and resources optimization, Power Clean should be switched off.

TABLET SETTING

This setting allows to optimize the cycle performances according the type of detergent used. Push the Tablet button for 3 seconds (until the indicator lights up) if you are using the combined detergents in tablet (rinse aid, salt and deteregent in 1 dose). If you are using powder detergent or liquid detergent, the Tablet indicator on the control panel has to be off.

START/RESUME BUTTON

Push this button to start the selected program: the indicator lights up and goes off at the end of the program. When the door is opened during a washing cycle, the cycle is temporarily paused: the Start indicator blinks. To resume the cycle push Start button and close the door within 3 seconds.

CANCEL/OFF BUTTON

Push this button to switch off the control panel. If pressed when a program is running it cancels the program ongoing draining water for 1 minute (0:01 is shown into the display). If pressed when the dishwasher is switched off, it drains any possible liquids from dishwasher (1 minute process).

MULTIZONE

Allows you to choose the washing zones. Press this button (repeatedly) to select the wash zones:

both racks

only lower rack

only upper rack (including cutlery rack)

- indicator lits

RINSE AID INDICATOR

When lit (at the end of the cycle), the rinse aid dispenser needs to be refilled.

SALT INDICATOR

When lit (at the end of the cycle), the salt reservoir needs to be refilled.

WASH TIME DISPLAY

Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates the time remaining until program start (h.00) below 1h (0:min). If “Fx Ey” messages appears on the display, see page 9 - chapter “What to do if...”.

OPERATION INDICATOR

A LED light projected on the floor indicates that the dishwasher is working.

Quick reference guide

Chart

Whirpool is a registered trademark of Whirpool USA

GB -1-

1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without any options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.

2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.

3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.

Table of programs

Deterge

Consumption

Drying

Phase

Programs

Available

options

Loading instructions

Litres kWh

Minutes

6th Sense Power Clean

40-70°C

Delay

Multizone

Power Clean

Use for normal soiled dishes with dried-on food. Senses the level of soiling on the dishes and adjusts the program accordingly. When the sensor is detecting the soil level an animation appears in the display and the cycle duration is updated. The Power Clean option is activated automatically with this program. To deactivate, press the Power Clean button on the control panel.

X 7-14 1.00-1.65 80-165 Full

Pre Wash cold

Delay

Multizone

Crockery to be washed later. — 4.0 0.03 14 NO

Fragile 40°C

Delay

Multizone

Light soiling, for example glasses and cups. X 10.0 0.85 100 Light

Rapid 45°C

Delay

Multizone

Lightly soiled crockery, with no dried-on food. X 11.0 0.80 30 NO

Eco

50°C

Delay

Multizone

Power Clean

Normally soiled crockery. Energy-saving program. X 11.5 0.93 240 Full

Fast Daily 60°C

Delay

Multizone

Normally soiled crockery. X 10.0 1.30 80 Full

Silent 50°C

Delay

Multizone

Normally soiled crockery, gentle and quiet thanks to the lower spray pressure (39 dbA).

X 13.0 1.20 290 Light

Intensive 65°C

Delay

Multizone

Power Clean

Recommended program for heavily soiled crockery, especially suitable for pans and saucepans.

X 14.0 1.60 145 Full

Steam

Delay

Multizone

Power Clean

Program including steam action dedicated for heavily soiled crockery, pots and pans. Soaking or hand pretreatment is no longer needed.

X 14.0 1.70 180 Full

P10

Hygiene

Delay

Multizone

Power Clean

Normally or heavily soiled crockery, with additional antibacterial wash. Program interruption (e.g. due to door opening) can compromise elimination of germs.

X 13.0 1.50 118 Full

Quick reference guide

Chart

GB -2-

1- salt reservoir 2- rinse aid dispenser 3- detergent dispenser 4- racks system 5,6,7,8- available functions on the panel 9- filters 10- spray arms

Water hardness should be set only

before the first wash or if water

hardness has been changed

Visual indicator (depending on the model). Unscrew cap.

Fill the salt reservoir with water

before the first wash only.

(depending on the model)

The salt level indicator lamp may remain lit at the end of several wash cycles. If the water hardness level falls within category (soft), no salt is required.

Salt indicator on the control panel Salt indicator on the salt reservoir cap

The indicator lamp lights up when SALT NEEDS TO BE ADDED.

green: OK.

clear: NEEDS TO BE ADDED

Daily check

Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)

Screw on the cap. Salt residual around the cap need to be removed. Some salt reservoir have a level indicator integrated in the cap (see below how to check).

- Press and hold together PROGRAM Selection and CANCEL/Off buttons for minimum 3 seconds.

- The current water hardness setting will be visible on the display.

- Press the PROGRAM Selection button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the next

press of the start button will set the level back to 1).

- Wait 30 seconds (control panel switches off) or press Start/Resume button to save setting.

1. Ask your water supply company what the water hardness

is...

2. ...enter this value

on your dishwasher

Suggestions for detergent use

German

degrees °dH

French

degrees °fH

English

degrees °eH

Water hardness

level

Insert value is shown in

the display

Gel or Powder

(rinse aid and salt)

Tab l et s

0 - 5 0 - 9 0 - 6.3 Soft 1

go to step 1

(see “Daily

check”)

6 - 10 10 - 18 7 - 12.6 Medium 2

11 - 15 19 - 27 13.3 - 18.9 Average 3

16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4

if water is HARD

extra salt needs

to be added

(go to step 1,

“Daily check”)

22 - 28 38 - 50 26.6 - 35 Hard 5

29 - 35 51 - 63 35.7 - 44.1 Very hard 6

36 - 50 64 - 90 44.8 - 62.4 Extremely hard 7

Add salt (never add detergent!)

min. 0.8 kg/max. 1 kg

Water hardness level is factory set for medium-hard water (level 4).

Even if you use tablets which include salt functionality, you must still add regeneration salt since such detergents are not effective enough at softening hard water.

At first time use, the salt reservoir has to be filled independently from water hardness level (see description below in step 1 “Daily check”).

Once regeneration salt is added, immediately start a wash program (the “Pre-wash” program alone is not sufficient). Residual saline solution or grains of salt can lead to deep-down corrosion, irreparably damaging the stainless steel components. The guarantee is not applicable if faults are caused by such circumstances.

How to set water hardness in order to always assure the best cleaning results

First time use

GB -3-

Daily use

Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations

Open the cover A

(press the dedicated button).

Only fill the detergent dispenser prior to starting a wash program.

Shut the cover by pressing dedicated

ribs.

If required, open the cover B (press the dedicated button).

Add rinse aid to the max. line ~150 ml

The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button to open the cover B. Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again.

Visual indicator

Check the rinse aid indicator to check the level into the dispenser.

(depending on the model) Rinse aid indicator on the control panel Rinse aid indicator on the dispenser

The indicator lamp lights up when RINSE AID NEEDS TO BE ADDED.

dark: OK. clear: NEEDS TO BE ADDED

Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance.

If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty drying and a higher rinse aid setting will not improve the situation.

Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend to form excess suds.

Use only one tablet per one cycle, only placed in detergent dispenser.

All types of tablets can be used, but for 2 in 1 type adding of salt is mandatory.

Some types of tablets may not dissolve completely during the short cycles (Rapid, Fragile, Handwash); placing the tablet on the tub bottom can help dissolving and washing.

Insert detergent: Tablet / powder / liquid into the big chamber.

Please look for the recommendation of the detergent manufacturer on the packaging of the

detergent product.

Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator

Daily check

GB -4-

Load cutlery with the handle into the pins.

Knives or cutlery with bulky handle can be loaded with

the head into the pins. How to remove cutlery rack (if available) - It could be useful to remove cutlery rack to load stem glasses in upper rack.

- Open the two retainers (D) to take off the rack. When the cutlery rack is

in place the retainers must always be closed.

D - CLOSED D - OPEN

Cutlery rackl

How to load the racks

GB -5-

+ 10 hidden pages