Whirlpool UMC5225DW0, UMC5225DB0, KMCS3022GBS0, KCMS2255BSS0, WMC50522AW0 Installation Guide

...

MICROWAVE OVEN BUILT-INTRIM

KIT

INSTALLATIONINSTRUCTIONS

Built-In Trim Kit Models MK2227 MK2220

UL listed for use over any electric or gas built-in oven, up to 30" (76.2 cm) wide

INSTRUCTIONSD'INSTALLATION

GARNITUREENCASTREEPOURFOURA MICRO-ONDES

Garniture encastrde pour modules MK2227 MK2220

Homologations UL pour utilisation au-dessus de tous les fours encastres electriques ou & gaz, jusqu'& 30" (76,2 cm) de largeur

Table of Contents / Tabledes mati_res

MICROWAVE OVEN SAFETY .................................................. 1

INSTALLATION INSTRUCTIONS ............................................. 2

Tools and Parts ...................................................................... 2

Location Requirements .......................................................... 2

Required Cutout Dimensions ................................................. 2

Trim Kit Frame Dimensions .................................................... 2

Electrical Requirements ......................................................... 3

Prepare Microwave Oven ....................................................... 3

Prepare Cutout/Cabinet Opening .......................................... 3

Install the Microwave Oven .................................................... 4

Install Trim Kit Frame ............................................................. 5

SECURITE DU FOUR A MICRO-ONDES ........................................... 7

INSTRUCTIONS D'INSTALLATION .................................................... 7

Outillage et pieces ............................................................................. 7

Exigences d'emplacement ................................................................ 7

Dimensions necessaires de I'ouverture d'encastrement .................. 8

Dimensions du cadre de la trousse de garniture .............................. 8

Specifications electriques ................................................................. 8

Preparation du four & micro-ondes ................................................... 9

Preparation de I'ouverture d'encastrement/dans le placard ............ 9

Installation du four & micro-ondes .................................................. 10

Installation du cadre de la trousse de garniture ............................. 11

MICROWAVE OVEN SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

W10434148A

INSTALLATIONINSTRUCTIONS

t'O0_S 3_J

Tools Needed Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed here.

• Measuring tape • Drill

• Pencil • 7/64" drill bit

• Phillips screwdriver

Parts Supplied (not shown to scale)

17" (43 2 c!) (

mln.

17%" (43.5 cm)

max.

l_/_e,,

(2.7 cm)

11/16"

(2.7 cm)

A. Trim kit frame overhang B. Cutout for lower oven

Rails (2)

Short screws (14)

(11 + 3 extra)

Bottom duct Trimkit frame

Long wood screws (6 - painted)

(4 + 2 extra)

Loc<:s' F!!equ :emen, ts

The microwave oven may be installed over a built-in oven. If installing over a built-in oven, make sure there is a minimum of 3" (7.6 cm) between the top of the lower oven cutout and the

microwave oven cutout floor. The microwave oven may also be installed in a cabinet by itself

(without a built-in oven below). For best usability, we recommend a minimum distance of 36" (91.4 cm) from the floor to the cutout

floor. Make sure the surrounding cabinetry has clearance to open and

close freely. Allow a clearance of at least 1%d' (4.0 cm) below the cutout floor (3" [7.6 cm] for installation above a built-in oven), and

a clearance of at least 2" (5.1 cm) above the cutout opening.

(5.1cm)

2 ,t

crn)

NOTES:

Height dimension is critical: 17" (43.2 cm)minimum, 17V8" (43.5 cm) maximum.

Width and depth measurements have _+1/16" (2 mm) tolerance.

3" (7.6 cm) minimum dimension is from lower oven cutout ceiling to microwave oven cutout floor.

Trim kit frame extends 1Vld' (2.7 cm) above and below the cutout opening.

I 11

267/8'' (68.2 cm)* I

293/4" (75.6 cm)** I

187/8"

(47.9 crn)

19/16 't

(

36"

A. Upper cabinet D. Lower cabinets

B. Microwave oven cutout E. Floor

C. Lower oven cutout

(91.4 c

3 ,I

1" (2.5 cm)

*27" (68.6 cm) trim kit

**30" (76.2 cm) trim kit

Eecff cc_ _eq(,.__"emen.ts

1. Unplug microwave oven before proceeding with installation.

2. Remove any loose items inside microwave oven.

3. Gently turn microwave oven onto its top, with the door facing forward (toward installer).

4. Align the #33 holes on the microwave oven bottom with the #33 holes on the rails, as shown, making sure the flanges are forward and pointing up.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Observe all governing codes and ordinances.

Required:

• A 120 volt, 60 Hz, AC only, 15- or 20-amp electrical supply with a fuse or circuit breaker.

Recommended:

• A time-delay fuse or time-delay circuit breaker.

• A separate circuit serving only this microwave oven.

GROUNDING iNSTRUCTiONS

[] For all cord connected appliances:

The microwave oven must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric

current. The microwave oven is equipped with a cord having a grounding wire with a grounding plug. The plug

must be plugged into an outlet that is properly installed and grounded.

WARNING: Improper use of the grounding plug can

result in a risk of electric shock. Consult a qualified electrician or serviceman if the grounding instructions are

not completely understood, or if doubt exists as to whether the microwave oven is properly grounded.

Do not use an extension cord. If the power supply cord is too short, have a qualified electrician or serviceman install

an outlet near the microwave oven.

SAVE THESE iNSTRUCTiONS

A B C

D E

A. Rails (2) D. Flanges B. Microwave oven bottom E.Door

C. Short screws (4)

5. Secure the rails to the microwave oven bottom using four short screws through the #33 hole sets.

P'ep(s_;e_.....,_,to_./_VCcJb },e 0 sen.loG

On the cutout floor, find and mark the centerline.

Place the bottom duct in the opening, with the flange resting against the bottom front facing of the opening.

A B C / /

iiiiiiiiiiiiiiiiiiiiiii_/ /

!!!!!!!!!!!!!!!!!!!!!!!i/

iiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiii

',_ iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiiiiiii//i:/ "",i .....iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_° o o s_s_s_s_s!s!s!s!s!!

:: iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

D E

A. Cutout floor B. Centerline C. Bottom duct

D. Bottom duct flange

E. Front facing

3. Align the center arrows on the bottom duct with the centerline drawn in Step 1 above.

A B

A.Bottom duct B.Center arrows, aligned with centerline

Mark the three mounting holes through the bottom duct onto the cutout floor.

I I I I

I I

1. Gently return microwave oven to its upright position.

2. Position microwave oven near cutout opening.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

3. Plug in microwave oven.

4. Align the rails with the rail guides on the bottom duct.

A. Short screws (3) B. Bottom duct mounting holes

5. Using 7/64" drill, drill pilot holes into the three holes marked in Step 4.

6. Realign and install the bottom duct with three short screws.

7. Using 7/64" drill, drill pilot holes through the four mounting holes of the bottom duct flange into the bottom front facing of

the cutout/cabinet opening.

A B

A. Bottom duct flange B. Mounting holes

A. Rail guides B. Rails

+ 8 hidden pages