Whirlpool WMC30516HZ Installation Manual

MICROWAVE OVEN BUILT-IN TRIM KIT

W10532204A

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

INSTALLATION INSTRUCTIONS

Built-In Trim Kit Models MK2167, MK2160

UL listed for use over any electric or gas built-in oven, up to 30" (76.2 cm) wide

INSTRUCTIONS D’INSTALLATION

GARNITURE ENCASTRÉE POUR FOUR À MICRO-ONDES

Garniture encastrée pour modèles MK2167, MK2160

Homologation UL pour utilisation au-dessus de tous les fours encastrés électriques ou gaz, jusqu’à 30" (76,2 cm) de largeur

Table of Contents / Table des matières

MICROWAVE OVEN SAFETY ...................................................1

INSTALLATION INSTRUCTIONS..............................................2

Tools and Parts .......................................................................2

Location Requirements...........................................................2

Required Cutout Dimensions..................................................2

Trim Kit Frame Dimensions.....................................................3

Electrical Requirements ..........................................................3

Prepare Microwave Oven........................................................3

Prepare Cutout/Cabinet Opening...........................................4

Install the Microwave Oven.....................................................5

Install Trim Kit Frame ..............................................................6

SÉCURITÉ DU FOUR À MICRO-ONDES...........................................7

INSTRUCTIONS D’INSTALLATION....................................................7

Outillage et pièces.............................................................................7

Exigences d'emplacement................................................................7

Dimensions nécessaires de l'ouverture d'encastrement..................8

Dimensions du cadre de la trousse de garniture..............................8

Spécifications électriques .................................................................9

Préparation du four à micro-ondes...................................................9

Préparation de l'ouverture d'encastrement....................................10

Installation du four à micro-ondes ..................................................11

Installation du cadre de la trousse de garniture .............................12

MICROWAVE OVEN SAFETY

INSTALLATION INSTRUCTIONS

(7.6 cm)

36"

(91.4 cm)

(5.1 cm)

1⁹⁄₁₆"

(4.0 cm)

(7.6 cm

)

(15.2 cm)

1¹⁄₁₆"

(2.7 cm)

1¹⁄₁₆"

(2.7 cm)

23¹⁄₈" (58.7 cm)

17¹⁄₈" (43.5 cm)

max.

17" (43.2 cm)

min.

For minimum depth requirements, see chart.

Tools and Parts

Tools Needed

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

■ Measuring tape

■ Pencil

■ Phillips screwdriver

■ Drill

■ 7/64" drill bit

Parts Supplied (not shown to scale

Rails (2) Bottom duct Trim kit frame

Short screws (14)

(11 + 3 extra)

Long wood screws (6 - painted)

(4 + 2 extra)

Location Requirements

The microwave oven may be installed over a built-in oven. If installing over a built-in oven, make sure there is a minimum of 3" (7.6 cm) between the top of the lower oven cutout and the microwave oven cutout floor.

The microwave oven may also be installed in a cabinet by itself (without a built-in oven below). For best usability, we recommend a minimum distance of 36" (91.4 cm) from the floor to the cutout floor.

Make sure the surrounding cabinetry has clearance to open and close freely. Allow a clearance of at least 1⁹⁄₁₆" (4.0 cm) below the cutout floor (3" [7.6 cm] for installation above a built-in oven), and a clearance of at least 2" (5.1 cm) above the cutout opening.

Required Cutout Dimensions

A. Trim kit frame overhang B. Cutout for lower oven C. Recommended region for receptacle

location (no less than 6" [15.2 cm] to the right of cutout centerline)

D. Cutout centerline

Receptacle Location Minimum Depth

Within recommended region

Outside recommended region

NOTES:

■ Depth requirements depend upon receptacle and its location

within or outside of recommended region. See illustration and chart above.

■ Height dimension is critical: 17" (43.2 cm) minimum, 17¹⁄₈"

(43.5 cm) maximum.

■ Width measurement has ±1/16" (2 mm) tolerance.

■ 3" (7.6 cm) minimum dimension is from lower oven cutout

ceiling to microwave oven cutout floor.

■ Trim kit frame extends 1¹⁄₁₆" (2.7 cm) above and below the

cutout opening.

18" (45.7 cm) with flush receptacle; 21" (53.2 cm) with non-flush receptacle

19¹⁄₂" (49.5 cm) with flush receptacle; 22¹⁄₂" (57.2 cm) with non-flush

receptacle

A. Upper cabinet B. Microwave oven cutout C. Lower oven cutout

D. Lower cabinets

E. Floor

Trim Kit Frame Dimensions

26⁷⁄₈" (68.2 cm)** 29

³⁄₄" (75.6 cm)**

2¹⁄₁₆" (5.2 cm)*

3¹⁄₂" (8.9 cm)**

22³⁄₄" (57.8 cm)

12¹⁄₄

(31.1 cm

)

1³⁄₁₆" (3.0 cm)

19¹⁄₈"

(48.6 cm)

3⁷⁄₁₆"

(8.7 cm)

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

GROUNDING INSTRUCTIONS

SAVE THESE INSTRUCTIONS

■

For all cord connected appliances:

The microwave oven must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. The microwave oven is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.

WARNING: Improper use of the grounding plug can

result in a risk of electric shock. Consult a qualified electrician or serviceman if the grounding instructions are not completely understood, or if doubt exists as to whether the microwave oven is properly grounded.

Do not use an extension cord. If the power supply cord is too short, have a qualified electrician or serviceman install an outlet near the microwave oven.

ABC

*27" (68.6 cm) trim kit

**30" (76.2 cm) trim kit

Electrical Requirements

Recommended:

■ A time-delay fuse or time-delay circuit breaker.

■ A separate circuit serving only this microwave oven.

Observe all governing codes and ordinances.

Required:

■ A 120 volt, 60 Hz, AC only, 15- or 20-amp electrical supply

with a fuse or circuit breaker.

Prepare Microwave Oven

1. Unplug microwave oven before proceeding with installation.

2. Remove any loose items inside microwave oven.

3. Gently turn microwave oven onto its top, with the door facing

forward (toward installer).

4. Align the two rails on the microwave oven bottom, as shown,

making sure the flanges are forward and pointing up.

A. Rails (2) B. Microwave oven bottom C. Short screws (4)

5. Secure the rails to the microwave oven bottom using four

short screws.

D. Flanges

E. Door

Prepare Cutout/Cabinet Opening

A B

1. On the cutout floor, find and mark the centerline.

2. Place the bottom duct in the opening, with the flange resting

against the bottom front facing of the opening.

A. Cutout floor B. Centerline C. Bottom duct

3. Align the center arrows on the bottom duct with the centerline

drawn in Step 1 above.

D. Bottom duct flange

E. Front facing

4. Mark the three mounting holes through the bottom duct onto

the cutout floor.

A. Short screws (3) B. Bottom duct mounting holes

5. Using 7/64" drill, drill pilot holes into the three holes marked in

Step 4.

6. Realign and install the bottom duct with three short screws.

7. Using 7/64" drill, drill pilot holes through the four mounting

holes of the bottom duct flange into the bottom front facing of the cutout/cabinet opening.

A. Bottom duct flange B. Mounting holes

A. Bottom duct B. Center arrows, aligned with centerline

+ 8 hidden pages