You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't
follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
WARNING: If the information in this manual is not followed exactly, a fire or explosion
may result causing property damage, personal injury or death.
– Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
– WHAT TO DO IF YOU SMELL GAS:
•
Do not try to light any appliance.
•
Do not touch any electrical switch.
•
Do not use any phone in your building.
•
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
•
If you cannot reach your gas supplier, call the fire department.
– Installation and service must be performed by a qualified installer, service agency or
the gas supplier.
WARNING: Gas leaks cannot always be detected by smell.
Gas suppliers recommend that you use a gas detector approved by UL or CSA.
For more information, contact your gas supplier.
If a gas leak is detected, follow the “What to do if you smell gas” instructions.
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.
3
The Anti-Tip Bracket
Tip Over Hazard
A child or adult can tip the range and be killed.
Verify the anti-tip bracket has been properly installed and engaged per installation instructions.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed and engaged.
Failure to follow these instructions can result in death or serious burns to children and adults.
To verify the anti-tip bracket is installed and engaged:
• Slide range forward.
• Look for the anti-tip bracket securely attached to floor or wall.
• Slide range back so rear range foot is under anti-tip bracket.
• See installation instructions for details.
WARNING
Anti-Tip
Bracket
Range Foot
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
To reduce the risk of fire, electrical shock,
injury to persons, or damage when using the range, follow
basic precautions, including the following:
■ WARNING:
TO REDUCE THE RISK OF TIPPING OF
THE RANGE, THE RANGE MUST BE SECURED BY
PROPERLY INSTALLED ANTI-TIP DEVICES. TO CHECK
IF THE DEVICES ARE INSTALLED PROPERLY, SLIDE
RANGE FORWARD, LOOK FOR ANTI-TIP BRACKET
SECURELY ATTACHED TO FLOOR OR WALL, AND
SLIDE RANGE BACK SO REAR RANGE FOOT IS UNDER
ANTI-TIP BRACKET.
■ WARNING:
NEVER use this appliance as a space
heater to heat or warm the room. Doing so may result in
carbon monoxide poisoning and overheating of the oven.
■ WARNING:
NEVER cover any slots, holes or passages
in the oven bottom or cover an entire rack with materials
such as aluminum foil. Doing so blocks air flow through the
oven and may cause carbon monoxide poisoning.
Aluminum foil linings may also trap heat, causing a fire
hazard.
■ CAUTION:
Do not store items of interest to children in
cabinets above a range or on the backguard of a range –
children climbing on the range to reach items could be
seriously injured.
■
Proper Installation – The range, when installed, must be
electrically grounded in accordance with local codes or, in
the absence of local codes, with the
National Electrical
Code, ANSI/NFPA 70
. In Canada, the range must be
electrically grounded in accordance with Canadian
Electrical Code. Be sure the range is properly installed and
grounded by a qualified technician.
■
This range is equipped with a three-prong grounding plug
for your protection against shock hazard and should be
plugged directly into a properly grounded receptacle. Do
not cut or remove the grounding prong from this plug.
■
Disconnect power before servicing.
■
Injuries may result from the misuse of appliance doors or
drawers such as stepping, leaning, or sitting on the doors
or drawers.
■
Maintenance – Keep range area clear and free from
combustible materials, gasoline, and other flammable
vapors and liquids.
■
Storage in or on the Range – Flammable materials should
not be stored in an oven or near surface units.
■
Top burner flame size should be adjusted so it does not
extend beyond the edge of the cooking utensil.
For self-cleaning ranges –
■
Before Self-Cleaning the Oven – Remove broiler pan and
other utensils. Wipe off all excessive spillage before
initiating the cleaning cycle.
The range will not tip during normal use. However, the range can tip if you apply too much force or weight to the open door without the
anti-tip bracket fastened down properly.
4
COOKTOP USE
E
D
C
B
A
WARNING
Fire Hazard
Do not let the burner flame extend beyond the edge of
the pan.
Turn off all controls when not cooking.
Failure to follow these instructions can result in death
or fire.
REMEMBER: When range is in use or (on some models)
during the Self-Cleaning cycle, the entire cooktop area may
become hot.
A
B
D
E
C
C
D
A
This manual covers different models. The range you have purchased may have some or all of the items listed. The locations and
appearances of the items shown here may not match those of your model.
A. Left front control knob
B. Left rear control knob
Cooktop Controls
IMPORTANT: Your range is factory-set for use with Natural gas. If
you wish to use LP gas, an LP Gas Conversion Kit is included
with your new range. See the “Gas Conversions” section of the
Installation Instructions for details on making this conversion.
Electric igniters automatically light the surface burners when
control knobs are turned to IGNITE.
The large burners (16,000, 14,000 and 12,500 Btu/h [British
Thermal Units]) provide the highest heat setting, and are ideal for
cooking large quantities of food or liquid, using large pots and
pans. The small burners (9,200 and 5,000 Btu/h) allow more
accurate simmer control at the lowest setting, and are ideal for
cooking smaller quantities of food, using smaller pots and pans.
Before setting a control knob, place filled cookware on the grate.
Do not operate a burner while using empty cookware or without
any cookware on the grate.
NOTE: Visually check that the burner has lit. If the burner does
not ignite, listen for a clicking sound. If you do not hear the igniter
click, turn the burner off. Check for a tripped circuit breaker or
blown household fuse.
Check that the control knob is pressed completely down on the
valve shaft. If the spark igniter still does not operate, call a trained
repair specialist.
To S et :
1. Push in and turn knob counterclockwise to IGNITE.
All the surface burners will click. Only the burner with the
control knob turned to Ignite will produce a flame.
C. Center burner (on some models)D. Right rear control knob
2. Turn knob anywhere between HIGH and LOW. Use the
following chart as a guide when setting heat levels.
SETTINGRECOMMENDED USE
IGNITE
HIGH
Medium■ Hold a rapid boil.
LOW
E. Right front control knob
■ Light the burner.
■ Start food cooking.
■ Bring liquid to a boil.
■ Quickly brown or sear food.
■ Fry or sauté foods.
■ Cook soups, sauces and gravies.
■ Stew or steam foods.
■ Keep food warm.
■ Simmer.
Sealed Surface Burners
A. Burner cap
B. Burner base
IMPORTANT: Do not obstruct the flow of combustion and
ventilation air around the burner grate edges.
C. Alignment pins
D. Igniter
E. Gas tube opening
5
Burner cap: Always keep the burner cap in place when using a
B
A
A
B
surface burner. A clean burner cap will help avoid poor ignition
and uneven flames. Always clean the burner cap after a spillover
and routinely remove and clean the caps according to the
“General Cleaning” section.
Gas tube opening: Gas must flow freely throughout the gas tube
opening for the burner to light properly. Keep this area free of soil
and do not allow spills, food, cleaning agents or any other
material to enter the gas tube opening. Keep spillovers out of the
gas tube by always using a burner cap.
A. 1-1¹⁄₂" (2.5-3.8 cm)
B. Burner ports
Burner ports: Check burner flames occasionally for proper size
and shape as shown in the previous illustration. A good flame is
blue in color, not yellow. Keep this area free of soil and do not
allow spills, food, cleaning agents or any other material to enter
the burner ports.
To Clean:
IMPORTANT: Before cleaning, make sure all controls are off and
the oven and cooktop are cool. Do not use oven cleaners, bleach
or rust removers.
1. Remove the burner cap from the burner base and clean
according to “General Cleaning” section.
2. Clean the gas tube opening with a damp cloth.
3. Clean clogged burner ports with a straight pin as shown. Do
not enlarge or distort the port. Do not use a wooden
toothpick. If the burner needs to be adjusted, contact a
trained repair specialist.
4. Replace the burner cap, making sure the alignment pins are
properly aligned with the burner cap.
A. Incorrect
B. Correct
5. Turn on the burner. If the burner does not light, check cap
alignment. If the burner still does not light, do not service the
sealed burner yourself. Contact a trained repair specialist.
Home Canning
When canning for long periods, alternate the use of surface
burners between batches. This allows time for the most recently
used areas to cool.
■ Center the canner on the grate above the burner.
■ Do not place canner on 2 surface burners at the same time.
■ For more information, contact your local agricultural
department. Companies that manufacture home canning
products can also offer assistance.
Cookware
IMPORTANT: Do not leave empty cookware on a hot surface
cooking area, element or surface burner.
Ideal cookware should have a flat bottom, straight sides and a
well-fitting lid, and the material should be of medium-to-heavy
thickness.
Rough finishes may scratch the cooktop or grates. Aluminum and
copper may be used as a core or base in cookware. However,
when used as a base they can leave permanent marks on the
cooktop or grates.
Cookware material is a factor in how quickly and evenly heat is
transferred, which affects cooking results. A nonstick finish has
the same characteristics as its base material. For example,
aluminum cookware with a nonstick finish will take on the
properties of aluminum.
Cookware with nonstick surfaces should not be used under the
broiler.
Use the following chart as a guide for cookware material
characteristics.
COOKWARECHARACTERISTICS
Aluminum
Cast iron■ Heats slowly and evenly.
Ceramic or
Ceramic glass
Copper
Earthenware
Porcelain
enamel-on-steel
or cast iron
Stainless steel
■ Heats quickly and evenly.
■ Suitable for all types of cooking.
■ Medium or heavy thickness is best for
most cooking tasks.
■ Good for browning and frying.
■ Maintains heat for slow cooking.
■ Follow manufacturer’s instructions.
■ Heats slowly, but unevenly.
■ Ideal results on low to medium heat
settings.
■ Heats very quickly and evenly.
■ Follow manufacturer’s instructions.
■ Use on low heat settings.
■ See stainless steel or cast iron.
■ Heats quickly, but unevenly.
■ A core or base of aluminum or copper on
stainless steel provides even heating.
6
ELECTRONIC OVEN CONTROLS
A
D
E
F
G
H
I
J
K
L
M
N
O
B
C
This manual covers different models. The range you have purchased may have some or all of the items listed. The locations and
appearances of the items shown here may not match those of your model.
A. Upper oven settings
B. Cook time
C. Start time
D. Oven display
E. Number keypad
F. Up pe r o ve n s t art
G. Timer set/off
H. Settings
Display
When power is first supplied to the range, or if a power failure has
occurred, 12:00 will appear on the display. See the “Clock”
section to set time of day.
When the oven is not in use, the display shows the time of day,
unless the oven is in Energy Save mode.
Cancel
Cancel stops any function except the Clock, Timer and Control
Lock.
Oven Lights
While the oven doors are closed, press the Oven Light icon on
the keypad to turn the lights on and off. Both oven lights will
come on when either door is open. The oven lights will not come
on during the Self-Clean cycle.
Oven Timer
The Oven Timer can be set in hours or minutes up to 9 hours and
59 minutes, and counts down the set time. The Oven Timer does
not start or stop the oven.
To S et :
1. Press TIMER SET/OFF.
2. Press the number keypads to set the length of time in hr-hr-
min-min. Leading zeroes do not have to be entered. For
example, for 2 minutes, enter “2.”
3. Press TIMER SET/OFF to begin the countdown. If enabled,
end-of-cycle tones will sound at end of countdown.
4. Press TIMER SET/OFF twice to cancel the Oven Timer and
return to the time of day. Do not press Cancel because the
oven will turn off.
5. If the Oven Timer is running, but not in the display, press
TIMER SET/OFF to display the countdown for 5 seconds.
I. Upper oven cancel
J. Lower oven cancel
K. Lower oven start/
control lock
L. Oven light
M. Clock
N. Precise Clean
O. Lower oven settings
Energy Save
The Energy Save mode deactivates the display to reduce energy
consumption.
To Activate the Energy Save Mode:
1. Press and hold SETTINGS for 3 seconds. “Energy saver on.”
will appear in the upper text area.
2. The setting will be activated after 5 minutes.
Any mode may be used with the range in Energy Save by
simply selecting the desired mode.
To Deactivate the Energy Save Mode:
1. Press and hold SETTINGS for 3 seconds. “Energy saver off.”
will appear in the upper text area.
2. The clock will reappear in the display, and the range can be
operated as usual.
Clock
To change the clock between 12-hour and 24-hour format, see
“12/24 HOUR (Adjusting the Clock Format)” in the “Settings”
section.
To Set the Time of Day:
Before setting, make sure the oven and Oven Timer are off.
1. Press the Clock icon. “Clock: Press 3 for AM and Press 6 for
PM” will scroll.
2. Use the number keypad to select AM or PM.
“Set Time” will display.
3. Use the number keypad to enter the current time.
4. Press the Clock icon or press START. “Time Set” will display
in the upper text area for 5 seconds. Once it disappears, the
time is set.
To Cancel:
Press the TIMER SET/OFF pad.
7
Settings
The Settings function enables you to personalize audible tones
and oven operation to suit your needs. After completing your
adjustments, press CANCEL or wait 30 seconds for the display to
show the time of day. To change any of the following settings,
press SETTINGS until the correct display text appears, and then
follow the instructions in the appropriate section. See the
following “Settings Quick Reference Chart.”
Settings Quick Reference Chart
Display TextDefault SettingTo change Setting
TEMP UNITFahrenheitPress (1) for Celsius
SOUNDOnPress (1) for OFF
SOUND VOLUMEHighPress (1) for LOW
END TONEOnPress (1) for OFF
Sound Volume (Adjusting Sound Volume)
The oven sound is factory set for High but can be changed to Low.
1. Press SETTINGS until “SOUND VOLUME” is displayed.
2. Press the “1” keypad to adjust the setting.
3. Press any START or CANCEL to save the setting and exit.
End Tone (Adjusting End Tone On or Off)
The end tone is factory set for On but can be changed to Off.
1. Press SETTINGS until “END TONE” is displayed.
2. Press the “1” keypad to adjust the setting.
3. Press any START or CANCEL to save the setting and exit.
Keypress Tone (Adjusting Keypress Tone On or Off)
The keypress tone is factory set for On but can be changed to Off.
1. Press SETTINGS until “KEYPRESS TONE” is displayed.
2. Press the “1” keypad to adjust the setting.
3. Press any START or CANCEL to save the setting and exit.
KEYPRESS TONEOnPress (1) for OFF
REMINDER TONEOnPress (1) for OFF
12/24 HOUR12 HrPress (1) for 24 HR
SABBATHOffPress (1) for ON
12Hr AUTO_OFFOnPress (1) for OFF
LANGUAGEEnglishPress (1) for French
Press (2) for Spanish
TEMP CALIBUpper CalibratePress (1) for LOWER
CALIBRATE
Temp Unit (Fahrenheit and Celsius)
The temperature is preset at Fahrenheit, but can be changed to
Celsius.
1. Press SETTINGS until “TEMP UNIT” is displayed.
2. Press the “1” keypad to adjust the setting.
3. Press any START or CANCEL to save the setting and exit.
Sound (Tones)
Tones are audible signals, indicating the following:
Basic Functions
One tone
■ Valid pad press
■ End of Oven Timer (long tone)
■ Function has been entered
■ Oven is preheated
Three tones
■ Invalid pad press
Four tones
■ End of cycle
Sound (Adjust On or Off)
The oven sound is factory set for On but can be changed to Off.
1. Press SETTINGS until “SOUND” is displayed.
2. Press the “1” keypad to adjust the setting.
3. Press any START or CANCEL to save the setting and exit.
Reminder Tone (Adjusting Reminder Tone On or Off)
The reminder tone is factory set for On but can be changed to Off.
1. Press SETTINGS until “REMINDER TONE” is displayed.
2. Press the “1” keypad to adjust the setting.
3. Press any START or CANCEL to save the setting and exit.
12/24 Hour (Adjusting the Clock Format)
The clock can be set to display time in a 12-hour or 24-hour
format. The clock is set at the factory for the 12-hour format.
1. Press SETTINGS until “12/24 HOUR” is displayed.
2. Press the “1” keypad to adjust the setting.
3. Press any START or CANCEL to save the setting and exit.
Sabbath (Sabbath Mode)
Sabbath Mode configures the range to conform to Star-K Jewish
Sabbath requirements for a Bake cycle, including Timed Bake or
Delayed Bake functions. Refer to the “Sabbath Mode” section for
a full description of this feature. Sabbath Mode is factory set for
disabled, but can be changed to enabled.
1. Press SETTINGS until “SABBATH” is displayed.
2. Press the “1” keypad to adjust the setting.
3. Press any START or CANCEL to save the setting and exit.
12 Hr Auto Off (Adjust On or Off)
The oven control is set to automatically shut off the oven
12 hours after the oven turns on. This will not interfere with any
timed or delayed cook function.
1. Press SETTINGS until “12Hr AUTO_OFF” is displayed.
2. Press the “1” keypad to adjust the setting.
3. Press any START or CANCEL to save the setting and exit.
Language (Change Language Options)
The Language is factory preset to English but can be changed to
French or Spanish.
1. Press SETTINGS until “LANGUAGE” is displayed.
2. Press the “1” keypad to select French, or press the “2”
keypad to select Spanish.
In French, press the “1” keypad to select Spanish, or press the
“2” keypad to select English. In Spanish, press the “1” keypad
to select English, or press the “2” keypad to select French.
3. Press any START or CANCEL to save the setting and exit.
8
Oven Temperature Control
The oven provides accurate temperatures; however, it may cook
faster or slower than your previous oven, so the temperature
calibration can be adjusted. It can be changed in Fahrenheit or
Celsius.
Temperature adjustment applies to upper or lower ovens.
A minus sign means the oven will be cooler by the displayed
amount. The absence of a minus sign means the oven will be
warmer by the displayed amount. Use the following chart as a
guide.
ADJUSTMENT °F
(ADJUSTMENT °C)
COOKS FOOD
Temp Calib (Adjust Oven Temperature Calibration)
IMPORTANT: Do not use a thermometer to measure oven
temperature because opening the oven door may cause element
cycling to give incorrect readings.
1. Press SETTINGS until “TEMP CALIB” is displayed.
2. The range is factory set to UPPER CALIBRATE. Press the “1”
keypad to change the selected oven.
3. Press the “3” keypad to increase the temperature in 5°F (3°C)
increments, or press the “6” keypad to decrease the
temperature in 5°F (3°C) increments. The range is from -30°F
to +30°F (-18°C to 18°C).
4. Press any START or CANCEL to save the setting and exit.
10°F (6°C)...a little more
20°F (12°C)...moderately more
30°F (17°C)...much more
-10°F (-6°C)...a little less
-20°F (-12°C)...moderately less
-30°F (-17°C) ...much less
OVEN USE
Odors and smoke are normal when the oven is used the first few
times, or when it is heavily soiled.
IMPORTANT: The health of some birds is extremely sensitive to
the fumes given off. Exposure to the fumes may result in death to
certain birds. Always move birds to another closed and wellventilated room.
Preheating
The upper and lower ovens have Rapid and standard preheat
options. When only one oven is used (either upper or lower) the
oven in use will default to the Rapid preheat option. The Rapid
preheat option is only recommended for single-rack baking.
When both ovens are used simultaneously, the ovens will default
to the standard preheat option. The standard preheat option is
recommended for multi-rack baking in the lower oven. The upper
oven is used only for single-rack cooking.
When the lower oven is used independently, the oven will default
to the Rapid preheat option to be used for single-rack baking
only. To use the standard preheat option for multi-rack baking in
the lower oven, make the appropriate selection during Bake or
Convection Bake operation setup. Unused racks should be
removed prior to preheating oven.
To toggle between single or multi-rack baking, press START for
the desired oven after beginning the Bake or Convection Bake
mode.
Control Lockout
The oven controls can be locked out to avoid unintended use of
the oven.
The oven controls cannot be locked if the oven is in use.
The current time of day will remain in the display when the
controls are locked.
To Lock Controls:
1. Press and hold START for 3 seconds. “Control Locked” will
scroll in the upper text area. “Control Locked” will scroll while
the control is locking, then “Locked” is displayed.
“Locked” and time of day remain lit in the display
To Unlock Controls:
1. Press and hold START for 3 seconds.
“Unlocking” will scroll in the display for 3 seconds while the
controls are unlocking, and the time of day is displayed.
Aluminum Foil
IMPORTANT: To avoid permanent damage to the oven bottom
finish, do not line the oven bottom with any type of foil, liner or
cookware.
■ For best cooking results, do not cover entire rack with foil
because air must be able to move freely.
■ To catch spills, place foil on rack below dish. Make sure foil is
at least ¹⁄₂" (1.3 cm) larger than the dish and that it is turned
up at the edges.
Positioning Racks and Bakeware
IMPORTANT: To avoid permanent damage to the porcelain
finish, do not place food or bakeware directly on the oven door or
bottom.
Racks
■ Position racks before turning on the oven.
■ Do not position racks with bakeware on them.
■ Make sure racks are level.
■ The upper oven is equipped with 1 flat rack.
■ The lower oven is equipped with 2 flat racks.
■ Place food so it will not rise into the broil element. Allow at
least ½" (1.3 cm) between pans and the broil burner.
9
To Remove Oven Racks:
1
2
3
4
5
1
2
1
2
3
4
5
Flat Racks: Pull rack out to the stop position, raise the front edge,
and then lift out.
To Replace Oven Racks:
Flat Rack: Place rack on the rack support in the oven. Tilt the
front edge up slightly, and slide rack back until it clears the stop
position. Lower front and slide back into the oven.
Rack Positions - Upper Oven
Baking
FOODRACK POSITION
Convection Cooking
FUNCTIONNUMBER OF
RACKS USED
Convection baking13
Convection baking22 and 4
Convection roasting11 or 2
Multiple Rack Cooking
2-rack: Use rack positions 2 and 4 when baking 2 racks of pizza.
Stagger pizza so that the pizza on rack position 2 is toward the
right side of the oven and the pizza on rack position 4 is toward
the left side of the oven.
Baking Layer Cakes on 2 Racks
For best results when baking cakes on 2 racks, use rack
positions 2 and 4. Place the cakes on the racks as shown.
Cook functionRack position
Convect bake2 and 4
RACK
POSITION(S)
All foods1
Broiling
FOODRACK POSITION
Broiling1
Rack Positions - Lower Oven
Traditional Cooking
FOODRACK POSITION
Large roasts, turkeys1 or 2
Yeast breads, quick breads, muffins,
tube cakes, small cuts of meat and
poultry and 2-rack baking
2
Bake2 and 4
BAKEWARE
To cook food evenly, hot air must be able to circulate. Allow
2" (5.0 cm) of space around bakeware and oven walls. Use the
following chart as a guide.
NUMBER
OF PAN(S)
1Center of rack.
2Side by side or slightly staggered.
3 or 4Make sure that no bakeware piece is directly
POSITION ON RACK
over another. See illustrations for placement of
layer cakes.
The bakeware material affects cooking results. Follow
manufacturer’s recommendations and use the bakeware size
recommended in the recipe. Use the following chart as a guide.
BAKEWARE/
RECOMMENDATIONS
RESULTS
Light colored
aluminum
■ Light golden crusts
■ Even browning
Dark aluminum and
other bakeware with
dark, dull and/or
nonstick finish
■ Brown, crisp crusts
■ Use temperature and time
recommended in recipe.
■ May need to reduce baking
temperatures slightly.
■ Use suggested baking time.
■ For pies, breads and casseroles,
use temperature recommended in
recipe.
■ Place rack in center of oven.
Insulated cookie
sheets or baking pans
■ Little or no bottom
■ Place in the bottom third of oven.
■ May need to increase baking time.
browning
Stainless steel
■ Light, golden crusts
■ Uneven browning
Stoneware/Baking
stone
■ Crisp crusts
Ovenproof glassware,
ceramic glass or
■ May need to increase baking time.
■ Follow manufacturer’s
instructions.
■ May need to reduce baking
temperatures slightly.
ceramic
■ Brown, crisp crusts
Meat Thermometer
A meat thermometer is not supplied with this appliance. Follow
manufacturer's directions for using a meat thermometer. On
models without a temperature probe, use a meat thermometer to
determine whether meat, poultry and fish are cooked to the
desired degree of doneness. The internal temperature, not
appearance, should be used to determine doneness.
Oven Vents
A. Lower oven vent
B. Upper oven vent
The oven vents release hot air and moisture from the ovens, and
should not be blocked or covered. Blocking or covering the vents
will cause poor air circulation, affecting cooking and cleaning
results. Do not set plastics, paper or other items that could melt
or burn near the oven vents.
Baking
Before baking, position racks according to the “Positioning
Racks and Bakeware” section.
■ If only one oven is to be used, that oven will preheat more
quickly.
■ Allow at least ½" (1.3 cm) between the baking pan or
casserole and the top burner in the upper oven. Loaf, angel
food or bundt pans are not recommended in the upper oven.
■ When preheating with a baking/pizza stone inside the upper
oven, do not set oven above 400°F (205°C). To use baking/
pizza stones at temperatures above 400°F (205°C) in the
upper oven, put stone in after the preheat beep.
■ Use only one rack in the upper oven.
■ If your range is equipped with a convection fan in the lower
oven, the fan may turn on during non-convection cycles or
preheating.
To Bak e:
1. Press BAKE for the desired oven.
“BAKE” will scroll in the upper or lower text area (depending
on oven selection), and “350°F (175°C)” will be displayed.
“Set temp or” will scroll in the selected oven text area,
followed by “Push START.”
2. Use the number keypad to enter the desired temperature.
NOTE: The temperature may be changed at any time by
using the number keypad to enter the new temperature and
then pressing START for the desired oven. Changing the
temperature once food is placed in the oven could affect
performance.
3. (Optional) If a Set Cooking Time is desired, press COOK
TIME. Use the number keypad to enter the desired time.
“Push START” will scroll in the selected oven text area.
4. Press START for the desired oven.
If the upper oven is used, “Preheating” will appear in the
upper oven text area.
If the only the lower oven is used, “Rapid preheating for
single rack. Press START to preheat for multi rack baking.”
will appear. If no change is made, “Preheating for single rack
baking” will appear in the display. “Rapid preheating for
single rack baking” will scroll in the selected oven text area.
“Preheating” remains in the text area until the set temperature
is reached. See “Preheating” in the “Oven Use” section for
more information.
If multi-rack baking is desired, START for the desired oven
should be pressed again and “Standard preheat for multi rack
baking. Press START to preheat for single rack baking.” will
appear in the display, followed by “Preheating for multi rack
baking.”
5. When the preheat cycle is complete, insert food. “Insert food
for one rack baking” or “Insert food for multirack baking” will
appear in the selected oven text area.
“Bake” will scroll in the selected oven text area until CANCEL
for the desired oven is pressed.
6. Place food in the oven when the preheat tone sounds.
7. Press CANCEL for the desired oven when finished.
8. Remove food from the oven.
NOTE: If a Set Cooking Time is to be used when only one
oven is used, increase the cook time by 10 minutes. If a Set
Cooking Time is to be used when both ovens are used or
multi-rack baking in the lower oven, increase the cook time
by 15 minutes. When the Set Cooking Time expires, the
oven(s) will turn off.
11
Broiling
Broiling uses direct radiant heat to cook food. The lower the
temperature, the slower the cooking. Thicker cuts and unevenly
shaped pieces of meat, fish and poultry may cook better at lower
broiling temperatures.
■ For best results, use the lower oven and a broiler pan with
grid (not provided). They are designed to drain juices and help
avoid spatter and smoke.
If you would like to purchase a broiler pan, one may be
ordered. See “Assistance or Service” section to order.
■ For proper draining, do not cover the grid with foil. The
bottom of the pan may be lined with aluminum foil for easier
cleaning.
■ Trim excess fat to reduce spattering. Slit the remaining fat on
the edges to avoid curling.
■ Select HIGH/550°F (288°C) broil for most broiling. Select
LOW/450°F (232°C) broil for low-temperature broiling of
longer cooking foods such as poultry to avoid over browning.
■ The Broil feature is only available in the upper oven.
■ Pull out oven rack to stop position before turning or removing
food. Use tongs to turn food to avoid the loss of juices. Very
thin cuts of fish, poultry or meat may not need to be turned.
■ After broiling, remove the pan from the oven when removing
the food. Drippings will bake on the pan if left in the heated
oven, making cleaning more difficult.
Before broiling, position rack according to the Broiling Chart.
Preheat oven for 5 minutes, position food on grid in the broiler
pan, then place it in the center of the oven rack. Close the door.
BROILING CHART
Broil times are based on a 5-minute preheat. Times are guidelines only and may need to be adjusted for individual tastes. Turn meat
halfway through cooking time. Recommended rack positions are numbered from the bottom (1) to the top (5). For diagram, see the
“Positioning Racks and Bakeware” section.
FOODUPPER OVEN RACK
Steak
1" (2.5 cm) thick
medium1HIGH12-16
Ground meat patties
4 oz (113 g), ³₄" (2.0 cm) thick
up to 12, well-done
up to 6, well-done
Pork chops
1" (2.5 cm) thick,
well-done1HIGH20-25
Chicken
bone-in, skin-on breast pieces
well-done1LOW30-40
Fish*
Filets, flaky
Steaks, 1" (2.5 cm) thick, flaky
POSITION
1
1
1
1
To Broil Using Hi/Low Temperature Settings:
1. Close the oven door.
2. Press BROIL for the desired oven.
“BROIL” will scroll in the selected oven text area, and “HI” will
be displayed.
After 3 seconds, “Set temp or” will scroll in the upper text
area, followed by “Push START.”
3. Press “1” on the keypad for the High broil setting, or press
“2” for the Low broil setting.
4. Press START for the desired oven.
“Broiling” will scroll in the upper text area and remains there.
“BROIL” will scroll in the selected oven text area once the set
temperature is reached and remains there until CANCEL for
the desired oven is pressed.
NOTE: The broil temperature may be changed at any time by
pressing “1” on the keypad for the High broil setting or
pressing “2” for the Low broil setting and then pressing
START for the desired oven. Changing the temperature once
food is placed in the oven could affect performance.
5. Press CANCEL for the desired oven when finished.
6. Remove food from the oven.
SETTINGUPPER OVEN COOK TIME
HIGH
HIGH
LOW
LOW
(minutes)
15-20
12-16
6-7
10-14
*When broiling fish, spray broil pan with cooking oil. Do not turn fish filets.
12
Convection Cooking - Lower Oven Only
A
B
(on some models)
During convection cooking, the fan provides increased hot air
circulation throughout the oven. The movement of heated air
around the food helps to speed up cooking by penetrating the
cooler outer surfaces.
NOTE: The convection fan may run in any non-convection cycle
or during preheat.
■ It is important not to cover foods so that surface areas remain
exposed to the circulating air, allowing browning and crisping.
■ Keep heat loss to a minimum by opening the oven door only
when necessary.
■ Choose cookie sheets without sides and roasting pans with
lower sides to allow air to move freely around the food.
■ Test baked goods for doneness a few minutes before the
minimum cooking time with a method such as a toothpick.
■ Use a meat thermometer to determine the doneness of meats
and poultry. Check the temperature of pork and poultry in 2 or
3 different places, including the thickest part.
■ Before convection cooking, position the rack(s) according to
the “Positioning Racks and Bakeware” section.
■ When using more than one rack, position bakeware/
cookware on the racks to allow movement of the fan
circulated air around the food. See the “Positioning Racks
and Bakeware” section.
■ If the oven is full, extra cooking time may be needed.
■ For optimal cooking results, do not cover food.
■ When roasting poultry and meat, use a broiler pan and grid. It
is not necessary to wait for the oven to preheat, unless
recommended in the recipe. To order a broiling pan, see
“Assistance or Service” section.
A. Broiler grid
B. Broiler pan
Convection Baking
Use Convect for single or multiple-rack baking. When convection
baking, reduce the recipe baking temperature by 25°F (15°C).
To Set Convect Bake:
1. Press CONVECT until “CONVECT BAKE” is displayed in the
lower text area, followed by “Push START.”
2. Press START for the desired oven.
“Set temp or Push START” will scroll in the display.
3. Use the number keypad to enter the desired temperature.
4. Press START for the desired oven.
“CONVECT BAKE” will scroll in the lower oven text area, and
“Rapid preheating for single rack. Press Start to preheat for
multi-rack baking” will scroll in the lower oven text area until
the set temperature is reached.
NOTE: If the upper oven is on, the lower oven will default to
the standard preheat/multi-rack baking option.
5. If multi-rack baking is desired, press START for the desired
oven when prompted in the display.
If multi-rack baking is selected, “Standard preheating for
multi rack baking. Press Start to preheat for single rack” will
appear in the display, followed by “Preheating for multi rack
baking.”
6. “Insert food for one rack baking only” will scroll twice in the
lower text area once the one-rack preheat temperature is
reached.
If multi-rack backing was selected, or if the upper oven is on,
“Insert food for multirack baking” will scroll twice in the lower
text area once the multi-rack preheat temperature is reached.
7. When the preheat cycle is complete, “CONVECT BAKE” will
appear in the lower oven text area until Cancel for the desired
oven is pressed.
8. Place food in the oven.
To change the oven temperature during cooking, use the
number keypad to enter the desired temperature, and then
press START for the desired oven.
9. Press CANCEL for the desired oven when finished.
10. Remove food from the oven.
Convect Broiling
1. Press CONVECT until “CONVECT BROIL” is displayed in the
lower text area, followed by “Push START.”
2. Press START for the desired oven.
“Set temp or” will scroll in the lower oven text area, followed
by “Push START.”
3. Use the number keypad to enter the desired temperature.
4. Press START for the desired oven.
“CONVECT BROIL” will appear in the lower oven text area,
followed by “Preheating.”
“Preheating” remains in the lower oven text area until the set
temperature is reached.
5. When the preheat cycle is complete, “CONVECT BROIL” will
appear in the lower text area. The set temperature will also be
displayed.
6. To change the oven temperature during cooking, use the
number keypad to enter the desired temperature, and then
press START for the desired oven.
“CONVECT BROIL” will remain in the lower oven text area
until Cancel for the desired oven is pressed.
7. Press CANCEL for the desired oven when finished.
8. Remove food from the oven.
Convection Roasting
1. Press CONVECT until “CONVECT ROAST” is displayed in the
lower text area, followed by “Push START.”
2. Press START for the desired oven.
“Set temp or” will scroll in the lower oven text area, followed
by “Push START.”
3. Use the number keypad to enter the desired temperature.
13
4. Press START for the desired oven.
WARNING
Food Poisoning Hazard
Do not let food sit in oven more than one hour before
or after cooking.
Doing so can result in food poisoning or sickness.
“CONVECT ROAST” will appear in the lower oven text area,
followed by “Preheating.”
“Preheating” remains in the lower oven text area until the set
temperature is reached.
5. When the preheat cycle is complete, “CONVECT ROAST” will
appear in the lower text area. The set temperature will also be
displayed.
6. To change the oven temperature during cooking, use the
number keypad to enter the desired temperature, and then
press START for the desired oven.
“CONVECT ROAST” will remain in the lower oven text area
until Cancel for the desired oven is pressed.
7. Press CANCEL for the desired oven when finished.
8. Remove food from the oven.
Keep Warm Feature
IMPORTANT: Food must be at serving temperature before
placing it in the warmed oven. Food may be held up to 1 hour;
however, breads and casseroles may become too dry if left in the
oven during the Keep Warm feature.
The Keep Warm feature allows hot cooked foods to stay at serving
temperature. It can also be used at the end of a timed cook.
To Use :
1. Press KEEP WARM for the desired oven.
“KEEP WARM” will scroll in the upper or lower text area
(depending on oven selection), and 170°F (77°C) will be
displayed.
“Set temp or” will scroll in the selected oven text area,
followed by “Push START.”
2. Use the number keypad to enter the desired temperature.
The temperature can be set from 145°F (63°C) to 190°F (85°C).
NOTE: The temperature may be changed at any time by
using the number keypad to enter the desired temperature
and then pressing START for the desired oven. Changing the
temperature once food is placed in the oven could affect
performance.
3. Press START for the desired oven.
“Keeping Warm” will appear in the text area, and the set
temperature will be displayed until the set temperature is
reached.
4. “WARM” and the temperature will be displayed while the
Keep Warm setting is active or until Cancel for the desired
oven is pressed.
5. Place food in the oven.
To change the oven temperature during cooking, use the
number keypad to enter the desired temperature and then
press START for the desired oven.
6. Press CANCEL for the desired oven when finished.
7. Remove food from the oven.
To Cancel Keep Warm Feature:
Press CANCEL for the desired oven.
14
Sabbath Mode
The Sabbath Mode allows the range to operate in compliance
with the Star-K Jewish Sabbath requirements for a Bake cycle,
including Timed Bake or Delayed Bake functions. To use the
Sabbath Mode on this range, note the following:
■ The Sabbath Mode feature must first be enabled. This is done
only one time and only if Sabbath Mode is expected to be
used at a later time.
■ When Sabbath Mode is enabled all range features and
functions operate the same as before Sabbath Mode was
enabled.
■ When Sabbath Mode is enabled and activated it can be used
for any Bake, Timed Bake or Delayed Bake cycle by
completing the steps in “To Activate Sabbath Mode” in this
section.
When Sabbath Mode is activated your range will run under the
following conditions:
■ All cooking functions on both ovens are disabled except for
Bake, Timed Bake and Delayed Bake.
■ The following keypads can be used: Bake, Cancel, Start,
Oven Timer and the number keypad.
■ The following features are disabled and cannot be used: all
tones and chimes; timers; 12 Hour Shutoff; Oven Cleaning
and Energy Save.
■ Cooktop elements can be enabled for use during Sabbath
mode.
■ The oven light will not change and will remain on or off all the
time, even if the Oven Light keypad is pressed or the oven
doors are opened or closed.
■ For best results, cooking should be done on one rack in the
upper oven and one rack in the lower oven.
To Enable Sabbath Mode Capability (one time only):
Sabbath Mode must be enabled to allow the control to run a
Bake, Timed Bake or Delayed Bake under the conditions listed
previously.
1. Press SETTINGS until “SABBATH” appears in the upper text
area.
2. Press “1” to enable Sabbath Mode.
3. “ON Selected” will scroll twice in the text area. The oven is
now enabled to be run in Sabbath Mode.
4. Press OFF to exit and display the time of day. Sabbath Mode
remains enabled.
NOTE: To disable the Sabbath Mode, repeat the previous
steps 1-4. In Step 3, the display reads “OFF Selected.”
To Activate Sabbath Mode:
Sabbath Mode can be activated for a Bake, Timed Bake or
Delayed Bake if Sabbath Mode has been enabled.
1. Press BAKE.
NOTE: Sabbath Mode cannot be activated for Convect Bake
or Convect Roast.
2. Press the number keypad to set a temperature other than
350°F (177°C).
3. Press START for the desired oven.
For timed cooking in Sabbath Mode, press COOK TIME, then
the number keypad to set the desired cook time.
4. If Sabbath Mode is to be used for both ovens, start a Bake,
Timed Bake or Delayed Bake in the second oven.
5. Press SETTINGS, then press “7.” “SAb” will appear in the
display.
For a Timed Bake function, the time will also be displayed
when the oven starts heating.
To Adjust Temperature (when Sabbath Mode is running in
WARNING
Food Poisoning Hazard
Do not let food sit in oven more than one hour before
or after cooking.
Doing so can result in food poisoning or sickness.
only one oven):
1. Press the number keypad for the desired temperature setting
as shown in the chart below. No temperature change will
appear in the display.
2. Press and hold START for the desired oven longer than
1 second to set the temperature change. No temperature
change will appear in the display.
To Adjust Temperature (when Sabbath Mode is running in
both ovens):
1. Press BAKE for the desired oven.
2. Press the number keypad for the desired temperature setting
as shown in the chart above. No temperature change will
appear in the display.
3. Press and hold START for the desired oven longer than
1 second to set the temperature change. No temperature
change will appear in the display.
TemperatureNumber
Pad
To Deactivate Sabbath Mode:
Sabbath Mode can be deactivated at any time during an active
Sabbath Mode.
Press SETTINGS, then press “7” to return to regular baking, or
press CANCEL for the desired oven to turn off the range.
If a Power Failure Occurs During Sabbath Mode
If a power failure occurs during Sabbath Mode, and the upper
text area displays “Sabbath,” press any CANCEL to exit Sabbath
Mode. The display will show the time of day. Sabbath Mode is no
longer active, but it is still enabled for the range.
Timed/Delay Cooking
Pad
The Cook Time feature allows the oven(s) to cook for a set length
of time. The Start Time feature allows the oven(s) to be set to turn
on at a certain time of day. The Start Time feature should not be
used for food such as breads and cakes because they may not
bake properly.
The Cook Time feature is available on most cycles except Precise
Clean and Keep Warm.
The Start Time feature is available on the most cycles except
Keep Warm.
To Set a Cook Time:
1. Press the button for any cooking function except Precise
Clean or Keep Warm for the desired oven.
Use the number keypad to enter a temperature other than the
one displayed. Then press START for the desired oven.
2. Press COOK TIME.
3. Use the number keypad to enter the length of time to cook.
4. Press START for the desired oven.
The cook time countdown will appear on the oven display.
When the stop time is reached, the oven will shut off
automatically, and end-of-cycle tones will sound.
To Set a Delay Cooking Time:
Before setting, make sure the clock is set to the correct time of
day. See the “Clock” section.
1. Press the button for any cooking function except Precise
Clean or Keep Warm for the desired oven.
Use the number keypad to enter a temperature other than the
one displayed then press START for the desired oven.
2. Press START TIME.
3. Press the “1” keypad to select the upper oven, or press the
“2” keypad to select the lower oven.
4. Use the number keypad to enter the delay start time. The
delay start time is the amount of time by which you want to
delay the start.
5. Press START for the desired oven.
6. Use the number keypad to enter the desired length of
cooking time.
7. Press START for the desired oven.
The start time is automatically calculated and displayed.
The delay countdown appears on the oven display.
When the start time is reached, the oven will automatically
turn on. The cook time countdown will appear on the oven
display.
The set temperature and minute time countdown will appear
on the oven display.
When the stop time is reached, the oven will shut off
automatically, and end-of-cycle tones will sound.
15
Loading...
+ 33 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.