Whirlpool WGD9500TW2, WGD9500TW1, WGD9500TW0, WGD9500TU1, WGD9500TU0 Owner’s Manual

...

ELECTRONIC

GASDRYER

Inthe U.S.A., for questions about features, operation/perlormance,

parts, accessories or service call: 1-800-253-1301

InCanada, for assistance, installation and service call: 1-800-807-6777

or visit our website at... www.whirlpool,com or www,whirlpooLca

SECHEUSEAGAZ

ELECTRONIQUE

W10122320A

Pour assistance, installation ou service composez le :

ou visitez notre site web &._www,whirlpool.ca

Table of Contents/Table des matieres ........................ 2

1-800-807-6777

TABLEOFCON[ENTS

TABLEDESMATIERES

DRYER SAFETY .............................................................................. 3

INSTALLATION INSTRUCTIONS .................................................. 5

Tools and Parts ............................................................................ 5

Options ......................................................................................... 5

Location Requirements ............................................................... 6

Electrical Requirements ............................................................... 8

Gas Supply Requirements ........................................................... 8

Venting Requirements .................................................................. 9

Plan Vent System ....................................................................... 11

Install Vent System ..................................................................... 12

Install Leveling Legs ................................................................... 12

Make Gas Connection ............................................................... 13

Connect Vent .............................................................................. 13

Connect Inlet Hose ..................................................................... 13

Level Dryer ................................................................................. 14

Complete Installation ................................................................. 14

DRYER USE .................................................................................. 15

Starting Your Dryer ..................................................................... 15

Stopping Your Dryer .................................................................. 17

Pausing or Restarting ................................................................. 17

Control Locked ........................................................................... 17

Drying and Cycle Tips ................................................................ 17

Status Lights .............................................................................. 17

Cycles ......................................................................................... 18

Additional Features .................................................................... 19

Changing Cycles, Options and Modifiers .................................. 20

Drying Rack Option .................................................................... 20

DRYER CARE .............................................................................. 21

Cleaning the Dryer Location ...................................................... 21

Cleaning the Lint Screen ............................................................ 21

Cleaning the Dryer Interior ......................................................... 22

Removing Accumulated Lint ...................................................... 22

Water Inlet Hoses ....................................................................... 22

Vacation, Storage and Moving Care .......................................... 22

Changing the Drum Light ........................................................... 22

TROUBLESHOOTING .................................................................. 23

ASSISTANCE OR SERVICE ......................................................... 25

WARRANTY .................................................................................. 26

S¢CURITE DE LA S¢CHEUSE .................................................... 27

INSTRUCTIONS D'INSTALLATION ............................................. 28

Outillage et pieces ...................................................................... 28

Options ....................................................................................... 29

Exigences d'emplacement ......................................................... 30

Specifications electriques .......................................................... 32

Alimentation en gaz .................................................................... 32

Exigences concernant I'evacuation ........................................... 33

Planification du systeme d'evacuation ...................................... 35

Installation du systeme d'evacuation ......................................... 36

Installation des pieds de nivellement ......................................... 37

Raccordement au gaz ................................................................ 37

Raccordement du conduit d'evacuation ................................... 38

Raccordement des tuyaux d'alimentation ................................. 38

Mise h niveau de la secheuse .................................................... 38

Achever I'installation .................................................................. 39

UTILISATION DE LA SECHEUSE ................................................ 40

Mise en marche de la secheuse ................................................ 40

Arr_t de la secheuse ................................................................... 42

Pause ou remise en marche ....................................................... 42

Control Locked (verrouillage des commandes) ......................... 42

Conseils pour le sechage et les programmes ........................... 42

Temoins lumineux ...................................................................... 43

Programmes ............................................................................... 43

Caracteristiques supplementaires ............................................. 45

Changement des programmes, options et modificateurs .........45

Option de grille de sechage ....................................................... 46

ENTRETIEN DE LA S¢CHEUSE ................................................. 47

Nettoyage de I'emplacement de la secheuse ........................... 47

Nettoyage du filtre a charpie ...................................................... 47

Nettoyage de I'interieur de la secheuse ..................................... 47

Retrait de la charpie accumulee ................................................ 47

Tuyaux d'alimentation d'eau ...................................................... 48

Precautions a prendre avant les vacances,

un entreposage ou un dem6nagement ...................................... 48

Changement de I'ampoule d'eclairage du tambour .................. 48

DEPANNAGE ................................................................................. 49

ASSISTANCE OU SERVICE ......................................................... 51

GARANTI E ..................................................................................... 52

DRYERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

WARNING: For your safety, the information in this manual must be followed to minimize

the risk of fire or explosion, or to prevent property damage, personal injury, or death.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Clear the room, building, or area of all occupants.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

In the State of Massachusetts, the following installation instructions apply: [] Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

[] If using a ball valve, it shall be a T-handle type. [] A flexible gas connector, when used, must not exceed 3 feet.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,

including the following:

[] Read all instructions before using the dryer. [] Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to

a chemical reaction that could cause a load to catch fire.

[] Do not dry articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry- cleaning solvents, or other flammable or explosive substances as they give off vapors that could ignite or explode.

[] Do not allow children to play on or in the dryer. Close

supervision of children is necessary when the dryer is used near children.

[] Before the dryer is removed from service or discarded,

remove the door to the drying compartment.

[] Do not reach into the dryer if the drum is moving. [] Do not install or store the dryer where it will be exposed

to the weather.

[] Do not tamper with controls.

SAVE THESE INSTRUCTIONS

[] Do not repair or replace any part of the dryer or attempt

any servicing unless specifically recommended in this Use and Care Guide or in published user-repair instructions that you understand and have the skills to carry out.

[] Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric softener or product.

[] Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

[] Clean lint screen before or after each load. [] Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust, and dirt.

[] The interior of the dryer and exhaust vent should be

cleaned periodically by qualified service personnel.

[] See installation instructions for grounding requirements.

IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSi Z223.1/NFPA 54 or the Canadian Natural Gas and Propane installation Code, CSA B149.1.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA O22.1.

INSTALLATIONINSTRUCTIONS

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

8" or 10" pipe wrench • 8" or 10" adjustable •

wrench (for gas connections) •

Flat-blade screwdriver • Adjustable wrench that

opens to 1" (2.5 cm) or hex-head socket wrench

(for adjusting dryer feet) v4" nut driver or socket •

wrench •

Parts supplied

Remove parts package from dryer drum. Check that all parts are included.

A B C D

A. Leveling legs (4) B. "Y" connector C. Short inlet hose

D. Inlet hose with right-angle connector

E.Rubber washer

NOTE: Do not use leveling legs supplied with dryer if installing on a pedestal.

Parts needed Check local codes and with gas supplier. Check existing gas

supply, electrical supply and venting. Read "Electrical Requirements," "Gas Supply Requirements" and "Venting Requirements" before purchasing parts.

• For close-clearance installations between 31.5" (80.01 cm) and 37" (93.98 cm), see "Plan Vent System" section for

venting requirements.

Level Knife

Vent clamps

Pipe-joint compound resistant to LP gas

Caulking gun and compound (for installing

new exhaust vent) Pliers

Tape measure

Pedestal

Are you placing the dryer on a pedestal? You have the option of purchasing pedestals of different heights separately for this dryer. You may select a 10" (25.4 cm) or 15.5" (39.4 cm) pedestal. These pedestals will add to the total height of the dryer for a total height of approximately 48" (121.9 cm) or 53.5" (135.9 cm), respectively.

For a garage installation, you will need to place the 10" (25.4 cm) pedestal at least 9" (22.9 cm) above the floor and the

15.5" (39.4 cm) pedestal at least 3.5" (8.9 cm) above the floor.

A B

A. 10" (25.4 cm) pedestal

B. 15.5" (39.4 cm) pedestal

The pedestals are available in several colors. To order, call the dealer from whom you purchased your dryer or

refer to the "Assistance or Service" section of this manual.

Pedestal Height Color Part Number

10" (25.4 cm} White WHP1000SQ 10" (25.4 cm} Biscuit WHP1000ST 10" (25.4 cm} Diamond Dust WHP1000SU

(Silver)

10" (25.4 cm} Black WHP1000SB

15.5" (39.4 cm) White WHP1500SQ

15.5" (39.4 cm} Biscuit WHP1500ST

15.5" (39.4 cm} Diamond Dust WHP1500SU (Silver)

15.5" (39.4 cm} Black WHP1500SB

Stack Kit

I-_- 37" ---_1

(93.9a era)

Mobile home installations require special parts (listed following) that may be ordered by calling the dealer from whom you purchased your dryer. For further information, please refer to the

"Assistance or Service" section of this manual.

• Mobile Home Installation Kit. Ask for Part Number 346764.

• Metal exhaust system hardware.

Are you planning to stack your DUET®washer and dryer? To do so, you will need to purchase a Stack Kit.

To order, call the dealer from whom you purchased your dryer or refer to the "Assistance or Service" section of this manual. Ask

for Part Number 8541503.

Door Reversal Kit

Are you planning to reverse the door swing direction on your DUET¢_dryer? To do so, you will need to purchase a Door

Reversal Kit. To order, call the dealer from whom you purchased your dryer or

refer to the "Assistance or Service" section of this manual. Ask for Part Number 8579666.

Backguard

If you are installing your DUET ° washer and dryer and wish to

avoid having loose items fall behind your machines, you may purchase a pair of washer/dryer backguards. These will reduce

the chance of items falling behind the machines during operation. To order, call the dealer from whom you purchased your dryer or

refer to the "Assistance or Service" section of this manual. Ask for Part Number 8212452 (White).

• For a garage installation, you will need to place the dryer at least 18" (46 cm) above the floor. If using a pedestal, you will need 18" (46 cm) to the bottom of the dryer.

Do not operate your dryer at temperatures below 45°F (7°C). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. This can result in longer drying times.

The dryer must not be installed or stored in an area where it will be exposed to water and/or weather.

Check code requirements. Some codes limit, or do not permit, installation of the dryer in garages, closets, mobile homes or sleeping quarters. Contact your local building inspector.

NOTE: No other fuel-burning appliance can be installed in the same closet as a dryer.

Installation clearances The location must be large enough to allow the dryer door to

open fully.

Dryer Dimensions

38,,I

(96.52Cil]}

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from dryer.

Place dryer at least 18 inches (46 cm) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

You will need

• A location that allows for proper exhaust installation. A gas dryer must be exhausted to the outdoors. See "Venting Requirements."

• A grounded electrical outlet located within 2 ft (61 cm) of either side of the dryer. See "Electrical Requirements."

• A sturdy floor to support the total dryer weight of 200 Ibs (90.7 kg). The combined weight of a companion appliance

should also be considered. Cold water faucets located within 4 ft (1.2 m) of the dryer, and

water pressure of 20-100 psi (137.9-689.6 kPa). You may use the cold water supply from your washer using the "Y" connector provided.

• 20-100 psi (138-690 kPa) for best performance. A level floor with a maximum slope of 1" (2.5 cm) under entire

dryer. If slope is greater than 1" (2.5 cm), install Extended Dryer Feet Kit, Part Number 279810. Clothes may not tumble properly, and automatic sensor cycles may not operate correctly if dryer is not level.

'311/2''

{80 cm) 27"

*Most installations require a minimum 5" (12.7 cm) clearance

behind the dryer for the exhaust vent with elbow. See "Venting Requirements."

Installation spacing for recessed area or closet installation

The following spacing dimensions are recommended for this dryer. This dryer has been tested for spacing of 0" (0 cm) clearance on the sides and rear. Recommended spacing should be considered for the following reasons:

• Additional spacing should be considered for ease of installation and servicing.

• Additional clearances might be required for wall, door and floor moldings.

• Additional spacing should be considered on all sides of the dryer to reduce noise transfer.

For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.

• Companion appliance spacing should also be considered.

Custom undercounter installation - Dryer only

1o_m>+L__JI I . o\ III II1_ I

38"rain.

(96.52cm_

1"* _ _-_27"_ _ 1''_

2,5 cm) 68,6 cm 2.5 cm

*Required spacing Closet installation - Dryer only

Recommended installation spacing for cabinet installation

• For cabinet installation, with a door, minimum ventilation openings in the top of the cabinet are required.

(22 9 crn)

(7.6cm)

I1"*_ 31v2"_h"-I

(2.5cm) (80cm) (12.7cm)

A. Side view - closet or confined area

B. Closet door with vents

*Required spacing

**For side or bottom venting, 2" (5.1 cm) spacing is allowed.

Recessed or closet installation - Dryer on pedestal

olo

1"-_t1_--27,,i*11_-1"

(2.5 cm) (68.6 cm) (2.5 cm) (2.5 cm) (80 cm) (12.7 cm)

A B

A.Recessed area B.Side view - closet or confined area

*Required spacing

**For side or bottom venting, 2" (5.1 cm) spacing is allowed.

1..1I_- 31v_"-_15""1

5"** 31%" 1" 1" 27" 1"

(12.7 crn) (80.0 crn) (2.5 crn) (2.5 cm)(68.6 crn) (2.5 crn)

*Required spacing

**For side or bottom venting, 2" (5.1 cm) spacing is allowed.

Recommended installation spacing for recessed or closet installation, with stacked washer and dryer

The dimensions shown are for the recommended spacing.

48 in? *

(310crn2)

.6¢rn)

iilili i_i_iili

__ __

24 in? *

(155crn2)

*Required spacing

3"* (7.6 cm)

6"*Zorn)

Vf_\X

76"

{193 cm)

5½,,*_,_,

(14 crn)

"_- (2.51cm)

_--27"_,, _ _ I"

68.6 cm 2.5 cm

*Required spacing

**For venting out the side, 2" (5.1 cm) spacing is allowed.

Mobile home - Additional installation requirements This dryer is suitable for mobile home installations. The

installation must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280) or Standard CAN/CSA-Z240

MH.

Mobile home installations require:

• Metal exhaust system hardware, which is available for

purchase from your dealer.

• Mobile Home Installation Kit Part Number 346764. See "Tools and Parts" section for information on ordering.

Special provisions must be made in mobile homes to introduce outside air into the dryer. The opening (such as a nearby window) should be at least twice as large as the dryer exhaust opening.

Explosion Hazard

Use a new CSA international approved gas supply line.

install a shut=off valve. Securely tighten all gas connections.

If connected to LP, have a qualified person make sure gas pressure does not exceed 13" (33 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter. Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

120 Volt, 60 Hz., AC only, 15- or 20-amp fused electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is also recommended that a separate circuit serving only this dryer be provided.

GROUNDING INSTRUCTIONS

• For a grounded, cord-connected dryer: This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This dryer is equipped with a cord having an equipment- grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes

and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is properly grounded. Do not modify the plug provided with the dryer: if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

Gas Type

Natural gas:

This dryer is equipped for use with Natural gas. It is design- certified by CSA International for LP (propane or butane) gases with appropriate conversion.

• Your dryer must have the correct burner for the type of gas in your home. Burner information is located on the rating plate in the door well of your dryer. If this information does not agree with the type of gas available, contact your dealer or call the phone numbers referenced in the "Assistance or

Service" section of this manual.

LP gas conversion: Conversion must be made by a qualified technician.

No attempt shall be made to convert the appliance from the gas specified on the model/serial rating plate for use with a different gas without consulting your gas company.

Gas supply line

• Must include r/8" NPT minimum plugged tapping accessible for test gauge connection, immediately upstream of the gas connection to the dryer. See illustration.

rA" IPS pipe is recommended. %" approved aluminum or copper tubing is acceptable for

lengths under 20 ft (6.1 m) if local codes and gas supplier permit.

If you are using Natural gas, do not use copper tubing. Lengths over 20 ft (6.1 m) should use larger tubing and a

different size adapter fitting. If your dryer has been converted to use LP gas, %" LP

compatible copper tubing can be used. If the total length of the supply line is more than 20 ft (6.1 m), use larger pipe.

NOTE: Pipe-joint compounds that resist the action of LP gas must be used. Do not use TEFLON _ttape.

1-®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

• Must include a shutoff valve: In the U.S.A.: An individual manual shutoff valve must be installed within

six (6)feet (1.8 m) of the dryer in accordance with the National Fuel Gas Code, ANSI Z223.1. The location should be easy to reach for opening and closing.

In Canada: An individual manual shutoff valve must be installed in

accordance with the B149.1, Natural Gas and Propane Installation Code. It is recommended that an individual

manual shutoff valve be installed within six (6) feet (1.8 m) of the dryer.

The location should be easy to reach for opening and closing.

A C E

Dryer gas pipe

• The gas pipe that comes out through the rear of your dryer has a %" male pipe thread.

A. Y2"NPT gas supply line

B. %" NPT dryer pipe

B D

A. %" flexible gas connector

B. %" pipe to flare adapter fitting C. Vs"NPT minimum plugged tapping D. Y2"NPT gas supply line

E. Gas shutoff valve

Gas supply connection requirements

• Use an elbow and a 3/8"flare x 3/8"NPT adapter fitting between the flexible gas connector and the dryer gas pipe, as needed to avoid kinking.

• Use only pipe-joint compound. Do not use TEFLON _t tape.

• This dryer must be connected to the gas supply line with a listed flexible gas connector that complies with the standard for connectors for gas appliances, ANSI Z21.24 or CSA 6.10.

Burner input requirements

Elevations above 10,000 ft (3,048 m):

• When installed above 10,000 ft (3,048 m) a 4% reduction of the burner Btu rating shown on the model/serial number plate is required for each 1,000 ft (305 m) increase in elevation.

Gas supply pressure testing

• The dryer must be disconnected from the gas supply piping system during pressure testing at pressures greater than 1/2psi.

*NOTE: If the dryer is mounted on a pedestal, the gas pipe height

must be an additional 10" (25.4 cm) or 15.5" (39.4 cm) from the

floor, depending on the pedestal model. For a garage

installation, the gas pipe height must be an additional 18" (46 cm) from the floor.

Fire Hazard

Use a heavy metal vent. Do not use a plastic vent.

Do not use a metal foil vent. Failure to follow these instructions can result in death

or fire.

WARNING: To reduce the risk of fire, this dryer MUST BE

EXHAUSTED OUTDOORS. IMPORTANT: Observe all governing codes and ordinances.

The dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling or a concealed space of a building.

If using an existing vent system

• Clean lint from the entire length of the system and make sure exhaust hood is not plugged with lint.

• Replace any plastic or metal foil vent with rigid or flexible heavy metal vent.

• Review Vent system chart. Modify existing vent system if necessary to achieve the best drying performance.

If this is a new vent system

Vent material

• Use a heavy metal vent. Do not use plastic or metal foil vent.

• 4" (10.2 cm) heavy metal exhaust vent and clamps must be used. DURASAFF Mventing products are recommended.

Clamps

• Use clamps to seal all joints.

• Exhaust vent must not be connected or secured with screws or other fastening devices that extend into the interior of the

duct. Do not use duct tape.

Clamp

Exhaust

4" (10.2cm) heavymetal exhaust vent

DURASAFE TM vent products can be purchased from your dealer or by calling Whirlpool Parts and Accessories. For more information, see the "Assistance or Service" section of

this manual.

Rigid metal vent

• For best drying performance, rigid metal vents are recommended.

• Rigid metal vent is recommended to avoid crushing and kinking.

Flexible metal vent

• Flexible metal vents are acceptable only if accessible for cleaning.

• Flexible metal vent must be fully extended and supported when the dryer is in its final location.

• Remove excess flexible metal vent to avoid sagging and kinking that may result in reduced airflow and poor performance.

• Do not install flexible metal vent in enclosed walls, ceilings or floors. •

Elbows

45° elbows provide better airflow than 90° elbows.

Recommended hood styles are shown here.

(10.2 cm)

A. Louvered hood style

B.Box hood style

The angled hood style (shown here) is acceptable.

v 0 21;m

An exhaust hood should cap the vent to keep rodents and insects from entering the home.

Exhaust hood must be at least 12" (30.5 cm) from the ground or any object that may be in the path of the exhaust (such as flowers, rocks or bushes, snow line, etc.).

Do not use an exhaust hood with a magnetic latch.

Good Better

improper venting can cause moisture and lint to collect indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint, wallpaper,

carpets, etc.

[] Housecleaning problems and health problems.

Choose your exhaust installation type

A. Dryer B. Elbow

C. Wall D. Exhaust hood

E. Clamps

F. Rigid metal or flexible metal vent

G. Vent length necessary to connect elbows H. Exhaust outlet

A B

A. Standard rear offset exhaust installation

B. Left or right side exhaust installation C. Bottom exhaust installation (not an option

with pedestal installations)

Alternate installations for close clearances Venting systems come in many varieties. Select the type best for

your installation. Two close-clearance installations are shown. Refer to the manufacturer's instructions.

Optional exhaust installations

This dryer can be converted to exhaust out the right side, left side, or through the bottom, Contact your local dealer to have the dryer converted.

Fire Hazard

Cover unused exhaust holes with one of the

following kits:

279818 (white) 279820 (black)

279925 (biscuit) 279969 (pewter)

280171 (diamond dust) Contact your local dealer.

Failure to follow these instructions can result in death,

fire, electrical shock, or serious injury.

i u

"x i \_ J

A B

A. Over-the-top installation (also available with one

offset elbow)

B. Periscope installation

NOTE: The following kits for close clearance alternate installations are available for purchase. To order, please see the

"Assistance or Service" section of this manual.

• Over-the-Top Installation: Part Number 4396028

• Periscope Installation (For use with dryer vent to wall vent mismatch):

Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm) mismatch

Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm) mismatch

Part Number 4396014 - 29" (73.66 cm) to 50" (127 cm) mismatch

Special provisions for mobile home installations The exhaust vent must be securely fastened to a noncombustible

portion of the mobile home structure and must not terminate beneath the mobile home, Terminate the exhaust vent outside,

Determine vent path

• Select the route that will provide the straightest and most direct path outdoors.

• Plan the installation to use the fewest number of elbows and turns.

• When using elbows or making turns, allow as much room as possible.

• Bend vent gradually to avoid kinking.

• Use the fewest 90 ° turns possible.

Determine vent length and elbows needed for best drying performance

• Use the following Vent system chart to determine type of vent material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified in the Vent system chart. Exhaust systems longer than those

specified will:

• Shorten the life of the dryer.

• Reduce performance, resulting in longer drying times and

increased energy usage.

The Vent system chart provides venting requirements that will help to achieve the best drying performance.

Excessive Weight Hazard

Use two or more people to move and install dryer. Failure to do so can result in back or other injury.

1. To protect the floor, use a large flat piece of cardboard from the dryer carton. Place cardboard under the entire back edge of the dryer.

2. Firmly grasp the body of the dryer. Gently lay the dryer on the cardboard. See illustration.

Vent system chart NOTE: Side and bottom exhaust installations have a 90° turn

inside the dryer. To determine maximum exhaust length, add one 90° turn to the chart.

Number of Type of Box or Angled

90° turns vent Iouvered hoods or elbows hoods

0 Rigid metal 64 ft (20 m) 58 ft (17.7 m)

Flexible metal 36 ft (11 m) 28 ft (8.5 m)

1 Rigid metal 54 ft (16.5 m) 48 ft (14.6 m)

Flexible metal 31 ft (9.4 m) 23 ft (7 m)

2 Rigid metal 44 ft (13.4 m) 38 ft (11.6 m)

Flexible metal 27 ft (8.2 m) 19 ft (5.8 m)

3 Rigid metal 35 ft (10.7 m) 29 ft (8.8 m)

Flexible metal 25 ft (7.6 m) 17 ft (5.2 m)

4 Rigid metal 27 ft (8.2 m) 21 ft (6.4 m)

Flexible metal 23 ft (7 m) 15 ft (4.6 m)

1. Install exhaust hood. Use caulking compound to seal exterior wall opening around exhaust hood.

2. Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.

3. Run vent to dryer location. Use the straightest path possible. See "Determine vent path" in "Plan Vent System." Avoid 90° turns. Use clamps to seal all joints. Do not use duct tape, screws or other fastening devices that extend into the interior

of the vent to secure vent.

3. Examine the leveling legs. Find the diamond marking.

4. Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs until the diamond marking is no longer

visible.

5. Place a carton corner post from dryer packaging under each of the 2 dryer back corners. Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location. Leave enough room to connect the exhaust vent or gas line.

For mobile home use

Gas dryers must be securely fastened to the floor at the time of installation.

Mobile home installations require a Mobile Home Installation Kit. For more information, please reference the service numbers in the "Assistance or Service" section of this manual.

Remove the red cap from the gas pipe.

Using a wrench to tighten, connect the gas supply to the dryer. Use pipe-joint compound on the threads of all non- flared male fittings. If flexible metal tubing is used, be sure

there are no kinks.

1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust outlet

and inside the exhaust hood. Check that the vent is secured to exhaust hood with a 4" (10.2 cm) clamp.

2. Move dryer into its final location. Do not crush or kink vent.

3. (On gas models) Check that there are no kinks in the flexible gas line.

4. Once the exhaust vent connection is made, remove the corner posts and cardboard.

A.Flared male fitting B.Non-flared male fitting

NOTE: For LP gas connections, you must use pipe-joint compound resistant to the action of LP gas. Do not use TEFLON °t tape.

A combination of pipe fittings must be used to connect the dryer to the existing gas line. Shown is a recommended connection. Your connection may be different, according to the supply line type, size and location.

A. %" flexible gas connector

B. %" dryerpipe C. _" to _" pipe elbow D. %" pipe-to-flare adapter fitting

Open the shutoff valve in the supply line. The valve is open when the handle is parallel to the gas pipe.

A. Closed valve

B. Open valve

Test all connections by brushing on an approved noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leak found.

The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses.

1. Turn cold water faucet off and remove washer inlet hose.

2. Remove old rubber washer from inlet hose and replace with new rubber washer provided. If space permits, attach the

brass female end of the "Y" connector to the cold water faucet.

NOTE: If "Y" connector can be attached directly to cold water faucet, go to Step 6. If "Y" connector cannot be attached

directly to the cold water faucet, the short hose must be used. Continue with Step 3.

3. Attach short hose to cold water faucet. Screw on coupling by hand until it is seated on faucet.

4. Using pliers, tighten the couplings with an additional two- thirds turn.

NOTE: Do not overtighten. Damage to the coupling can result.

5. Attach "Y" connector to brass male end of small hose. Screw on coupling by hand until it is seated on connector.

6. Attach straight end of long hose to "Y" connector.

7. Attach washer cold inlet hose to other end of "Y" connector. Screw on coupling by hand until it is seated on connector.

1-®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

8. Using pliers, tighten the coupling with an additional two- thirds turn.

A. Inlet to cold water

NOTE: Do not overtighten. Damage to the coupling can result.

9. Attach angled end of long hose to fill valve at bottom of dryer back panel. Screw on coupling by hand until it is seated on fill

valve connector.

f0. Using pliers, tighten the couplings with an additional two-

thirds turn.

f. Check that all parts are now installed. If there is an extra part,

go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Be sure the water faucets are on.

5. Check for leaks around "Y" connector, faucet and hoses.

6. Check the dryer's final location. Be sure the vent is not crushed or kinked.

7. Check that the dryer is level. See "Level Dryer."

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord, Failure to follow these instructions can result in death,

fire, or electrical shock.

NOTE: Do not overtighten. Damage to the coupling can result.

f 1. Check that the water faucets are on.

12. Check for leaks around "Y" connector, faucet and hoses.

Check the levelness of the dryer. Check levelness first side to side, then front to back.

If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs up or down and check again for

levelness.

8. Plug into a grounded 3 prong outlet. Turn on power.

9. Remove any protective film or tape remaining on the dryer.

10. Read "Dryer Use."

f 1. Wipe the dryer drum interior thoroughly with a damp cloth to

remove any dust.

12. If you live in a hard water area, use of a water softener is recommended to control the buildup of scale through the water system in the dryer. Over time, the buildup of lime scale may clog different parts of the water system which will reduce product performance. Excessive scale buildup may lead to the need for certain part replacement or repair.

13. Select a Timed Dry heated cycle, and start the dryer. Do not select the Air Only Temperature setting.

If the dryer will not start, check the following:

• Dryer is plugged into a grounded 3 prong outlet.

• Electrical supply is connected.

• Household fuse is intact and tight, or circuit breaker has

not tripped.

• Dryer door is closed.

14.

When the dryer has been running for 5 minutes, open the dryer door and feel for heat. If you feel heat, cancel cycle and close door. If you do not feel heat, turn off the dryer and check that the gas supply line shutoff valve is open.

• If the gas supply line shutoff valve is closed, open it, then

repeat the 5-minute test as outlined above.

• If the gas supply line shutoff valve is open, contact a

qualified technician.

DRYERUSE

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from dryer.

Do not dry anything that has ever had anything

flammable on it (even after washing).

Failure to follow these instructions can result in death,

explosion, or fire.

This manual covers several different models. Your dryer may not have all of the cycles and features described.

The following is a guide to starting your dryer. Please refer to specific sections of this manual for more detailed information.

f. Clean lint screen before each load. See "Cleaning the Lint

Screen."

2. Place laundry in dryer and shut door.

3. Press the POWER button then rotate the dial to select either an Automatic or Manual Cycle. The preset settings and drying

time for the cycle chosen will be displayed. NOTE: A default time is displayed when an Automatic Cycle

is selected. During the first few minutes of the drying process, the cycle time may automatically vary from the default time based on the size and fabric type of the load. Toward the end of the drying process, the estimated time display will adjust again, showing the final drying time.

Fire Hazard

No washer can completely remove oil. Do not dry anything that has ever had any type of oil on

it (including cooking oils).

Items containing foam, rubber, or plastic must be dried on a clothesline or by using an Air Cycle.

Failure to follow these instructions can result in death or fire.

To use an Automatic Cycle NOTE: A light next to each feature will glow green when the

feature is selected or will glow amber when the feature is selectable. The light will not glow when the selection is unavailable with the cycle or option combinations selected.

• Press the POWER button.

• Rotate the dial to select an Automatic Cycle.

• Select DRYNESS LEVEL to adjust how dry you want the load to be. As the cycle runs, the control senses the dryness of the load and adjusts the time automatically for the selected Dryness Level.

NOTE: Most loads may be dried using Normal, which is shown in boldface type on your control panel. Normal is the energy preferred dryness level and will use the least energy.

Noll"naJ More Less

The default dryness setting is Normal when an Auto Dry Cycle is selected. You can select a different dryness level, depending on your load, by pressing DRYNESS LEVEL and choosing More, Normal or Less. Selecting More, Normal or Less automatically adjusts the dryness level at which the dryer will shut off. Once a dryness level is set, it cannot be changed without stopping the cycle.

The Dryness Level can be changed only with Automatic Cycles.

• Press the WRINKLE SHIELD TM feature button if this option is desired.

• Press the CYCLE SIGNAL button to set end of cycle signal volume to desired level.

• Press the DAMP DRY CYCLE SIGNAL button to set damp dry signal volume to desired level.

• Press and hold START button until dryer starts (about

1 second).

Once an Automatic cycle has started, the WRINKLE SHIELD TM feature and cycle signals can be adjusted. Press the PAUSE/CANCEL key twice to clear the settings, allowing you to select another cycle and Dryness Level.

NOTE: Time and Temperature are not adjustable for Automatic Cycles. Pressing the DRY TIME or TEMPERATURE buttons will cause a triple beep, indicating that the time cannot be changed.

How Automatic Cycles Work The AccelerCare TM function improves drying performance

with Auto Moisture Sensing Plus, which advances the cycle as moisture is extracted from clothing. A thermistor (electronic temperature sensor) and moisture sensing strips in the dryer drum help measure the amount of moisture in the clothes as they tumble. An electronic control determines the load type to help save time, avoid overdrying, and increase the accuracy of the end dryness level. After the first 5 minutes of an automatic cycle, the estimated time display will adjust based on the approximate load size, cycle, dryness level

selected and amount of moisture left inthe clothes. When the clothes have reached approximately 80% of the dryness level

selected, the estimated time display will adjust again, showing the final drying time. The AccelerCare TM feature takes the guesswork out of drying time and enhances fabric

care.

To use a Manual Cycle

NOTE: A light next to each feature will glow green when the feature is selected or will glow amber when the feature is selectable. The light will not glow when the selection is unavailable with the cycle or option combinations selected.

• Press POWER. Rotate the dial to select a Manual Cycle.

Press the DRY TIME up or down buttons until the desired drying time is displayed. Press DRY TIME, and the time will change by 1-minute intervals. Press and hold DRY TIME, and the time will change by 5-minute intervals. The initial time displayed is the actual drying time.

AdjustManual

DryTime

Press TEMPERATURE until the desired temperature glows green.

High

Medium

Low

ExtraLow

Air Only

Temperature

AdjustManual

Cycles0nly

Temperature settings can be changed only with Manual Cycles.

• Press the WRINKLE SHIELD TM feature button if this option is desired.

• Press the CYCLE SIGNAL button to set end of cycle signal volume to desired level.

• Press and hold START button until dryer starts (about

1 second).

NOTE: Dryness Level is not adjustable for Manual or Steam Cycles. Pressing the Dryness Level button will cause the triple beep indicating that this option is not selectable.

While a Manual Cycle is running, you cannot change the cycle until you clear the settings. You can change the settings for Time, Temperature, the WRINKLE SHIELD TM feature and the cycle signals. Press the PAUSE/CANCEL key twice to clear the settings, allowing you to select another cycle.

To use a Steam Cycle

• Press the POWER button. Rotate the dial to select either the Enhanced Touch Up or

Quick Refresh cycles. Press the DRY TIME up or down buttons until the desired

drying time is displayed. Press DRY TIME, and the time will change by 1-minute intervals. Press and hold DRY TIME, and the time will change by 5-minute intervals. The initial time displayed is the actual drying time

NOTE: The More Time and Less Time buttons can be used only with Manual Cycles and the Enhanced Touch

Up Cycle.

AdjustManual

DryTime

®®

• Press TEMPERATURE until the desired temperature glows green.

NOTE: During the Enhanced Touch Up Cycle, you can change the settings for Time, Temperature, the WRINKLE SHIELD TM feature and Cycle Signal. During the Quick Refresh Cycle you can change the WRINKLE SHIELD TM feature and the Cycle Signal. Press STOP twice to stop the dryer and clear the settings. Select another cycle or option.

®®

The Dry Time feature can be used only with Manual Cycles and the Enhanced Touch Up Cycle.

+ 36 hidden pages